Sanji ZX40-KPW User manual

Enter your 4 digit code to reset
the immobilizer, the keypad led
will turn off, the vehicle can now
be driven. If entered incorrectly,
the unit will sound rapid beeps,
the immobilizer will not be reset.
Once the immobilizer has been
reset the vehicle can be driven.
If the ignition is off for 60 sec,
the immobilizer will arm up
automatically.
When the driver’s door is
opened the numbers will light up
to make it easy to see the
numbers at night for easy
operation. The numbers will also
turn on when any button is
pressed. The numbers will turn
off automatically.
2) RESETTING
THE
IMMOBILIZER
To reset the
immobilizer.
Factory default
code 1111
3) DRIVE MODE Drive mode.
drive
mode
5) NUMBER
LIGHTING
door open
LED
FLASHING
1) IMMOBILIZER
ARMED
Immobilizer
armed mode.
The keypad led will flash a
short flash every 3 seconds.
The vehicle is immobilized.
LED
FLASHING
LED
OFF
1 2 345
If an incorrect code is entered 4
times, the unit will lock up for
+- 10 minutes. The led will flash
and the unit will
beep.
4) LOCK UP
MODE
Lock up timer.
1 2 345
lock up mode
LED
FLASHING
RAPIDLY
6) CHANGING YOUR 4 DIGIT CODE
THE UNIT WILL COME DEFAULT FROM THE FACTORY WITH CODE 1 1 1 1
LOADED INTO THE KEYPAD. FOLLOW THE DETAILS BELOW ON HOW
TO CHANGE THE CODE. NOTE : YOU CAN NOT ENTER CHANGE CODE
MODE WHILE IN SERVICE MODE.
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
1 2 345
led flashing
slowly
1 2 345
IMMOBILIZER ARMED
ENTER EXISTING 4 DIGIT CODE
IMMOBILIZER RESET
HOLD BUTTONS 1 & 5 TOGETHER FOR +/- 2 SECONDS TO ENTER
“OPTIONS MODE”, YOU WILL GET 1 CONFIRMATION BEEP AND THE
LED WILL FLASH RAPIDLY THEN, PRESS AND HOLD BUTTON 5
UNTIL THE KEYPAD SOUNDS A LOUD BEEP AND THE LED TURNS
ON SOLID.
1 2 345
led on
solid
1 2 345
PRESS & HOLD BUTTON 1&5
OPTIONS MODE
UNIT IS NOW IN CHANGE CODE MODE
ENTER YOUR NEW 4 DIGIT CODE, AFTER THE CODE IS ENTERED THE
KEYPAD WILL SOUND A LOUD BEEP.
1 2 345
ENTER THE NEW 4 DIGIT CODE
BEEP
NOW ENTER YOUR NEW 4 DIGIT CODE AGAIN, TO VERIFY THE NEW
CODE. AFTER THE CODE IS ENTERED THE KEYPAD WILL SOUND A
LOUD BEEP, THE KEYPAD LED WILL START TO FLASH. THE 4 DIGIT
CODE HAS NOW BEEN SAVED AND THE UNIT WILL GO INTO ARMED
MODE..
1 2 345
ENTER THE NEW 4 DIGIT CODE
IF THE FIRST NEW CODE DOES NOT MATCH THE SECOND CODE, THEN
THE KEYPAD WILL SOUND A RAPID BEEP TO WARN YOU THAT THE
CODES DID NOT MATCH. THE NEW CODE WILL NOT BE SAVED, THE
UNIT WILL EXIT CHANGE CODE MODE.
RAPID
BEEPING
1 2 345
EXIT CHANGE CODE MODE
IF NO NEW CODE IS ENTERED WITHIN 2 MINUTES OR THE
IGNITION IS TURNED ON, THE UNIT WILL AUTOMATICALLY EXIT
CHANGE CODE MODE.
led off
led on
solid
led on
solid
led flashing
slowly
1 2 345
IMMOBILIZER ARMED
BEEP
BEEP
USER INSTRUCTIONS
button press
Read these instructions for correct system operation. All
points marked are optional features.
*
1 2 345
PRESS & HOLD BUTTON 5
UNTIL YOU HEAR A LOUD BEEP
led flashing rapidly
BEEP
drive
mode
IMPORTANT NOTE: THE ZX40KPW IS FITTED WITH DEFAULT
CODE 1111 AND IF THIS IS NOT CHANGED BY THE USER TO A NEW
USER CODE THE UNIT WILL SOUND A SERIES OF
LOUD BEEPS EVERY TIME THE IGNITION IS
TURNED ON.
ZX40-KPW
WIRELESS KEYPAD IMMOBILIZER
REV2
This function will only work if connected to a compatible real time
tracking system. Press any button for 3 sec and a panic signal will
be sent to the tracking unit. Panic is disabled in service and Hi-
jack mode.
PANIC MODE
Numbers light
up.
Press any button for 3 sec
r
1
1
1
1 2 345
TO ENTER SERVICE MODE
ENTER YOUR 4 DIGIT CODE THEN PRESS AND HOLD BUTTON 2 & 4
UNTIL THE KEYPAD SOUNDS A LOUD BEEP AND THE LED TURNS
OFF. THE UNIT HAS NOW EXITED SERVICE MODE.
TO EXIT SERVICE MODE
OPERATION IN SERVICE MODE
THE KEYPAD LED WILL BE ON SOLID, THE IMMOBILIZER WILL NOT
ARM UP DURING SERVICE MODE. THE VEHICLE CAN BE DRIVEN AT
ANY TIME.
AUTO EXIT MODE : IF THE IGNITION IS ON (DRIVE MODE) FOR MORE
THAN 15 MINUTES CONTINUAL DRIVE, THE UNIT WILL
AUTOMATICALLY EXIT SERVICE MODE WHEN THE IGNITION IS
TURNED OFF. IF THE IGNITION IS TURNED OFF BEFORE THE 15
MINUTE TIMER IS UP, THE 15 MINUTE TIMER WILL RESET.
7) SERVICE MODE OPERATION
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
THEN, PRESS AND HOLD BUTTON 2 & 4 UNTIL THE KEYPAD
SOUNDS 2 LOUD BEEPS AND THE LED TURNS ON SOLID.
1 2 345
led on
solid
1 2 345
UNIT IS NOW IN SERVICE MODE
2 BEEPS
PRESS & HOLD BUTTON 2&4
LED
FLASHING
LED
OFF
1
1
led off
1 2 345
1 2 345
BEEP
UNIT HAS NOW EXCITED SERVICE MODE
PRESS & HOLD BUTTON 2&4
SANJI SECURITY SYSTEMS (PTY) LTD 106 16TH RD, MIDRAND,
GAUTENG, SOUTH AFRICA. TEL [phone] FAX [phone]
E-mail: [email protected] http://www.sanji.co.za
QUICK GUIDE
LED FUNCTIONS
Keypad Led quick flash: Immobilizer Armed Mode.
Keypad Led ON: Service Mode.
Keypad Led OFF: Reset / Drive Mode.
Keypad Led Rapid flashing: Program Mode
PROGRAM OPTIONS
* Enter Service Mode: user code 2 & 4
* Exit Service Mode: 2 & 4
* Change Code Mode: user code 1 & 5 then 5
enter code enter code
* Hi-Jack Drivers Door: user code 1 & 5 then 3
* Hi-Jack Drivers Door & Forced: user code 1 & 5 then 3
* Hi-Jack Cancel: user code 1 & 5 then 3
* Learn Master Code: user code 1 & 5 then 1
enter six digit enter six digit
* Use Master Code: 3 & 5 enter six digit code

To reset the
unit back to
normal
operation, in
delay mode.
14) RESETTING
HI-JACK IN
DELAY MODE
*
Enter your 4 digit code to reset
hi-jack, if entered correctly the
unit will sound a loud beep and
exit hi-jack mode. If entered
incorrectly, the unit will sound
rapid beeps.
11) HI-JACK
OPERATION
Hi-jack delay
mode.
The Hi-Jack countdown period is
1 min 45s. Once in Hi-Jack delay
period the counter will continue
to count down irrespective of the
state of the ignition. Refer to
point 14 to reset hi-jack.
12) HI-JACK
WARNING
PERIOD
Hi-jack
warning
mode.
After the countdown period the
unit will enter the 50 second
warning period. The keypad will
beep and flash the led and the
vehicle will begin to stall
intermitently*. At any point in
time you can reset hi-jack, refer
to point 15.
*
13) FINAL
HI-JACK
To confirm
what phase
the unit is in.
In final hi-jack the keypad will
beep and the led will be on solid.
The immobilizer will be armed. At
any point in time you can reset
hi-jack, refer to point 15.
9) FORCED
HI-JACK
MODE
Forced hi-jack
in drive.
*
When you start the vehicle, the
unit will enter hi-jack, the keypad
led will give a 1 second flash.
Refer to point 14 to reset hi-jack.
10) DRIVER’S
DOOR
HI-JACK
To activate
door hi-jack.
In drive ie ignition “on” open then
close driver’s door, the keypad
led will give a 1 second flash and
the unit will enter hi-jack delay
period. The keypad backlighting
will switch on.
*
driver’s door
opened driver’s door
closed
1 2 345
led flashing rapidly
1 2 345
led on solid
HI-JACK OPERATION
Ignition
turned on
To reset the
unit back to
normal
operation, in
warning or
final mode.
15) RESETTING
HI-JACK IN
WARNING
OR FINAL
*
Press any button on the keypad
to stop the unit from beeping
(silent mode). You then have 6
seconds to enter your 4 digit
code to reset hi-jack. If no code
is entered the unit will start to
beep again. If entered incorrectly,
the unit will sound rapid beeps.
1 2 345
ENTER 4 DIGIT CODE
THE UNIT WILL COME DEFAULT FROM THE FACTORY WITH THE
HI-JACK FEATURES DEACTIVATED.
AVAILABLE ON THE ZX40-KP :
1. DRIVER’S DOOR HI-JACK ONLY: - DRIVERS DOOR HI-JACK WILL
ACTIVATE WHEN THE DRIVERS DOOR IS OPENED AND THEN CLOSED
WITH IGNITION ON.
2. DRIVER’S DOOR AND FORCED HI-JACK: - FORCED HI-JACK WILL
AUTO ACTIVATE EVERY TIME THE IGNITION SWITCH IS TURNED ON.
THERE ARE 2 HI-JACK FEATURES
8) HI-JACK FEATURES
THERE ARE 2 HI-JACK FEATURES AVAILABLE ON THE ZX40-KP :
1. DRIVER’S DOOR HI-JACK ONLY
DRIVERS DOOR HI-JACK WILL ACTIVATE WHEN THE DRIVERS DOOR
IN OPENED AND THEN CLOSED WITH IGNITION ON.
2. DRIVER’S DOOR AND FORCED HI-JACK.
1 2 345
ENTER 4 DIGIT CODE
Vehicle engine stall feature
will depend on vehicle make
and model and fitment
options
TO ACTIVATE DRIVER’S DOOR HI-JACK
THEN, PRESS AND HOLD BUTTON 1 & 5 UNTIL THE KEYPAD
SOUNDS ONE LOUD BEEP IE OPTIONS MODE. NOW PRESS
AND HOLD BUTTON 3 UNTIL YOU GET 2 BEEPS.
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
1 2 345
led flashing
slowly
1 2 345
IMMOBILIZER ARMED
ENTER EXISTING 4 DIGIT CODE
IMMOBILIZER RESET
led off
DRIVER’S DOOR
HI-JACK FEATURE
ACTIVATED
1 BEEP
1 2 345
PRESS & HOLD BUTTON 1&5
1 2 345
PRESS & HOLD BUTTON 3
2 BEEPS
TO ACTIVATE DRIVER’S DOOR AND FORCED HI-JACK
THEN, PRESS AND HOLD BUTTON 1 & 5 UNTIL THE KEYPAD
SOUNDS ONE LOUD BEEP IE OPTIONS MODE. NOW PRESS
AND HOLD BUTTON 3 UNTIL YOU GET 3 BEEPS.
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
1 2 345
led flashing
slowly
1 2 345
IMMOBILIZER ARMED
ENTER EXISTING 4 DIGIT CODE
IMMOBILIZER RESET
led off
DRIVER’S DOOR
AND
FORCED HI-JACK
FEATURES ACTIVATED
1 BEEP
1 2 345
PRESS & HOLD BUTTON 1&5
1 2 345
PRESS & HOLD BUTTON 3
3 BEEPS
THEN, PRESS AND HOLD BUTTON 1 & 5 UNTIL THE KEYPAD
SOUNDS ONE LOUD BEEP IE OPTIONS MODE. NOW PRESS
AND HOLD BUTTON 3 UNTIL YOU GET 1 BEEP.
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
1 2 345
led flashing
slowly
1 2 345
IMMOBILIZER ARMED
ENTER EXISTING 4 DIGIT CODE
IMMOBILIZER RESET
led off
TO DEACTIVATE ALL HI-JACK FEATURES
NO HI-JACK
FEATURES
ACTIVATED
1 BEEP
1 2 345
PRESS & HOLD BUTTON 1&5
1 2 345
PRESS & HOLD BUTTON 3
1 BEEP
16) LEARN MASTER CODE
RESET THE IMMOBILIZER WITH YOUR 4 DIGIT CODE.
1 2 345
led flashing
slowly
1 2 345
IMMOBILIZER ARMED
ENTER EXISTING 4 DIGIT CODE
IMMOBILIZER RESET
RESET THE UNIT AND HOLD BUTTONS 1 & 5 TOGETHER FOR +/- 2
SECONDS TO ENTER “OPTIONS MODE”, YOU WILL GET 1 CONFIRMATION
BEEP AND THE LED WILL FLASH RAPIDLY THEN, PRESS AND HOLD
BUTTON 1 UNTIL THE KEYPAD SOUNDS A LOUD BEEP. NOW ADD THE
6 DIGIT MASTER CODE, IT MUST BE ENTERED IN TWICE AS
CONFIRMATION. IF NO MASTER CODE IS INPUTTED WITHIN 2 MINUTES,
THE UNIT WILL AUTO EXIT (NO NEW CODE SAVED).
led off
IN ARMED MODE, HOLD BUTTONS 3 & 5 TOGETHER UNTIL YOU HEAR A
RAPID BEEP, THE UNIT IS NOW IN MASTER CODE MODE. YOU HAVE 45
SECONDS TO ENTER THE 6 DIGIT MASTER CODE TO RESET THE UNIT.
IF NO CODE IS ENTERED THE UNIT WILL REVERT BACK TO NORMAL
ARMED MODE (WAITING FOR NORMAL 4 DIGIT RESET CODE). THE UNIT
WILL SOUND A RAPID BEEP TO WARN THE USER THAT THE UNIT IS
OUT OF MASTER CODE MODE. NOTE: THE UNIT WILL ONLY ENTER
MASTER CODE MODE IF A 6 DIGIT CODE HAS BEEN LEARNT IN TO THE
UNIT. THIS IS A ONCE OFF MASTER RESET FACILITY. THE NEXT TIME
THE UNIT NEEDS TO BE RESET IT WILL BE WITH THE NORMAL 4 DIGIT
CODE.
18) USING THE MASTER CODE IN FINAL HI JACK
IN HI-JACK FINAL MODE, PRESS ANY BUTTON TO STOP THE UNIT
FROM BEEPING, THEN PRESS AND HOLD BUTTON 3 & 5 TOGETHER
UNTIL YOU HEAR A RAPID BEEP, THE UNIT IS NOW IN MASTER CODE
MODE. YOU CAN NOW ENTER THE 6 DIGIT MASTER CODE TO RESET
THE UNIT FROM HI-JACK. WHEN THE UNIT STARTS TO BEEP AGAIN
THE UNIT WILL EXIT MASTER CODE RESET MODE AND WILL REVERT
BACK TO WAIT FOR THE NORMAL 4 DIGIT RESET CODE.
Rapid beeps
1 2 345
PRESS & HOLD BUTTON 3&5
ENTER SIX DIGIT CODE
17) USING THE MASTER CODE IN ARMED MODE
Rapid beeps
1 2 345
PRESS & HOLD BUTTON 3&5
ENTER SIX DIGIT CODE
1 2 345
PRESS ANY KEY TO STOP BEEPING