Santa & Cole Arne User manual

Includedcomponents INSTALLATIONPROCEDUREFORLIGHTPOLE:
1. Liftthelightpoleintopositionovertheinstalledanchors(refertoArneanchorkit
installationguide)asshowninFig.1.Ensurethatthebaseplateisrestingonallfour
washers.
2. InstallwasherandhexnutasshowninFig.2.
3. Plumbandlevelthepoleandtightenallanchors.
4. Installluminaire.Refertopage2forconnectionsteps.
5. Connectwiringtotheweatherproofconnectorintheluminaire.Refertowiring
diagramonpage2.
6. Installthetopcaponthepole(shippedwiththepole).Iftheunithasatwistlock
receptacle,assemblethereceptacleandthetopcapasshowninFig.3andconnect
wiringbeforeinstallingthetopcap.
7. InstallthenutcoversasshowninFig.4.
ToolsRequired
•Safetyglasses
•Wrenches,1‐1/4”for4.5m,6mor8m(5in/6in)poleor1‐5/8”for10m(5in/8in)pole
•Wiringtoolsandconnectors
•Properpersonnel,craneorliftforhoistingunitontoanchors
•Level
•Dimmingcontrol,ifrequired
•Hexkey5/32”fornutcovers
•Twistlockphotoeye,ifrequired
LandscapeFormsisnotresponsibleforsitepreparationandfootings.Refertothe
installationguidefortheArnelightanchorkitforinstallingtheanchorbolts.
CAUTION! Thisunitisheavy.Toavoidinjuryordamagetothefinish,werecommendusing
acraneorliftforhoistingtheunitontotheanchors.
WARNING! Polemountedluminairesmustbeattachedeitherbeforeorimmediately after
poleinstallation. Failuretodosomaycausevibrationdamagetothepoleandwillvoidthe
polewarranty.
ASSEMBLEWITHCARE! Toprotectthisfinishduringassembly,placeunwrappedpowdercoated parts
onpackagingfoamorothernon‐marringsurface.Donotplaceorslidepowdercoated partson
concreteorotherhardortexturedsurface– thiswilldamagethefinishcausingrusttooccur.Use
touch‐uppaintonanygougesinthefinishcausedbyassemblytools.
4X‐ Nutcoverwith
1/4‐20x5/8”button
headcapscrew
Polewithbaseplate
4.5m 6m 8m 10m
Twistlockreceptacle
Polecap
Standard Fortwistlock
Fig.2– Installpole
Fig.3– Installtwistlock
receptacletotopcap
Installation Guide
Arne Column mount LED Light
www.landscapeforms.com Ph: 800.521.2546
Date: March 3, 2015
Page 1 of 2
Column
mount
Shortingcapfor
Twistlock
Fig.1–Poleorientation
HANDHOLE
ORIENTEDON
SIDEOPPOSITE
OFLUMINAIRE
SETBACK
SIDEWALK
Fig.4– Installnutcovers

LEDWIRINGDIAGRAM:withouttwistlock
PROCEDUREFORWIRINGARNELEDLUMINAIRES:
TheArnelightluminaireisassembledatthefactory.OpeningtheLEDareaoftheluminairewillvoid
thewarranty.
Thewiringschematicsaretobeusedtoconnecttheunittolinevoltage.Itistheresponsibilityof
theinstallertomakesurethatallconnectionsaremadeinaccordancewiththeNECandlocal
buildingcodes.Connectionhardwarenotincluded.
Line‐inwiresshouldbeconnectedtotheweatherproofconnectorasshown.Optionaldimming
controlisnotincluded.
Installation Guide
Arne Column mount LED Light
www.landscapeforms.com Ph: 800.521.2546
Date: March 3, 2015
Page 2 of 2
Columnmountstep1Columnmountstep2
ANGULAR
LOCKING
EVERY10°
Columnmountstep3
OPENGROMMET
Columnmountstep4
MAXTIGHTENING
TORQUE27Nm
MAXIMUM
TIGHTENING
TORQUE27Nm
Columnmountstep5
DONOTDISASSEMBLE
THELOWERPART
CABLE:MAXTIGHTENING
TORQUE8Nm
SCREW:MAXTIGHTENING
TORQUE6Nm