Santa & Cole Candela User manual

Included components
8m and 10m
pole heights
1x –wooden drill template
INSTALLATION PROCEDURE FOR ANCHOR BOLTS:
1. Prepare footing as required by local codes.
2. Install anchor hooks, hex nuts, washers and wooden template as shown in Fig 3.
Level template in all directions. Note: template thickness is less than base plate
thickness. Dimensions given account for the difference.
3. After footing has properly cured, remove wooden template. Do not remove lower
hex nuts or washers.
Included: hardware is galvanized
8m and 10m pole: (4) anchor bolts, 1”-8 UNC x 36” x 4” hook,
(8) heavy hex nuts, 1”-8 UNC, (8) flat washers, 1.06” ID x 2.00” OD x 0.15” thick
Landscape Forms is not responsible for site preparation and footings. The following
chart gives necessary information for calculating proper footing size, depending on
the specified light pole.
WARNING! Pole mounted luminaires must be attached either before or immediately
after pole installation. Failure to do so may cause vibration damage to the pole and
will void the pole warranty.
7” diameter base pole
Fig. 2 –Base plate orientation
to luminaire
Pole Size
Base Overturning
Moment (ft-lbf)
Base Shear
(lbf)
7"x.188“/5”x.250”x8m 11,682 567
8"x.250“/5”x.250”x8m 20,161 761
Tools Required
•Safety glasses
•Wrenches, 1-5/8” for 8m (5in/7in) pole
•Level
Fig.3-Anchor install detail
LIGHTING LAYOUT RECOMMENDATIONS:
Refer to the product data sheet available at www.landscapeforms.com for
recommendations for light pole spacing.
Installation Guide
Candela Area Light Anchor Kit and Pole
www.landscapeforms.com Ph: 800.521.2546
Date: December 17, 2019
Page 1 of 2
Fig. 1 –Sidewalk setback
HANDHOLE ORIENTED
ON SIDE OPPOSITE
OF LUMINAIRE
SETBACK
SIDEWALK
8” diameter base pole
4 PLACES
CONDUIT
OPENING

Included components
INSTALLATION PROCEDURE FOR LIGHT POLE:
1. Lift the light pole into position over the installed anchors (refer to Candela anchor kit
installation guide) as shown in Fig. 1. Ensure that the base plate is resting on all four
washers.
2. Install washer and hex nut as shown in Fig. 4.
3. Plumb and level the pole and tighten all anchors.
4. Refer to luminaire installation guide for attaching arms and luminaires.
5. Install the top cap on the pole (shipped with the pole). If the unit has a twist lock
receptacle, assemble the receptacle and the top cap as shown in Fig. 5 and connect
wiring before installing the top cap. Install provided shorting cap or photo-electric
control.
6. Install the nut covers as shown in Fig. 6.
Tools Required
•Safety glasses
•Wrenches, 1-5/8”
•Wiring tools and connectors
•Proper personnel, crane or lift for hoisting unit onto anchors
•Level
•Dimming control, if required
•5/32” Hex key for nut covers
•Twist lock photo eye, if required
Landscape Forms is not responsible for site preparation and footings. Refer to the
installation guide for the Candela light anchor kit for installing the anchor bolts.
CAUTION! This unit is heavy. To avoid injury or damage to the finish, we recommend
using a crane or lift for hoisting the unit onto the anchors.
WARNING! Pole mounted luminaires must be attached either before or immediately
after pole installation. Failure to do so may cause vibration damage to the pole and
will void the pole warranty.
ASSEMBLE WITH CARE! To protect this finish during assembly, place unwrapped powdercoated parts
on packaging foam or other non-marring surface. Do not place or slide powdercoated parts on concrete
or other hard or textured surface –this will damage the finish causing rust to occur. Use touch-up paint
on any gouges in the finish caused by assembly tools.
4X -Nut cover with
1/4-20 x 5/8” button
head cap screw
Pole with base plate
10m
8m
Twist lock receptacle,
optional
Pole cap
Standard For twist lock
Fig. 4 –Install pole
Installation Guide
Candela Area Light Anchor Kit and Pole
www.landscapeforms.com Ph: 800.521.2546
Date: December 17, 2019
Page 2 of 2
Shorting cap for
Twist lock,
optional
Fig. 6 –Install nut covers
Fig. 5– Install optional twist
lock receptacle to top cap