Santa & Cole Rama User manual

Included components
8m, 9m Pole Height
5in/7in dia
4.5m, 6m
Pole height
8m
Pole height
5in/6in dia
1x –wooden drill template
INSTALLATION PROCEDURE FOR ANCHOR BOLTS:
1. Prepare footing as required by local codes.
2. Install anchor hooks, hex nuts, washers and wooden template as shown in Fig 3 and
Fig. 4. Level template in all directions. Note: template thickness is less than base
plate thickness. Dimensions given account for the difference.
3. After footing has properly cured, remove wooden template. Do not remove lower
hex nuts or washers.
Included: hardware is galvanized
4.5m and 6m pole: (4) anchor bolts, 3/4”-10 x 17” x 3” hook ,
(8) heavy hex nuts, 3/4” x 10, (8) flat washers, .81 ID” x 1.5” OD x 0.13” thick
8m (5in/6in) pole: (4) anchor bolts, 3/4”-10 x 17” x 3” hook ,
(8) heavy hex nuts, 3/4” x 10, (8) flat washers, .81 ID” x 2” OD x 0.13” thick
8m and 9m (5in/7in) pole: (4) anchor bolts, 1”-8 x 36” x 4” hook,
(8) heavy hex nuts, 1” x 8, (8) flat washers, 1.06” ID x 2.00” OD x 0.15” thick
Landscape Forms is not responsible for site preparation and footings. The following
chart gives necessary information for calculating proper footing size, depending on the
specified light pole.
WARNING! Pole mounted luminaires must be attached either before or immediately
after pole installation. Failure to do so may cause vibration damage to the pole and will
void the pole warranty.
7” diameter base pole
5” diameter pole 6” diameter base pole
Fig. 1 –Sidewalk setback
Fig. 2 –Base plate
orientation
to luminaire
Pole Size Base Overturning Moment (ft-lbf
)
Base Shear (lbf)
5” x .125“ x 4.5m 4037 353
5” x .188“ x 6m 5874 400
6”/5” x .188” x 8m 8633 455
7”/5” x .188” x 8m 11,826 566
7”/5” x .188”x 9m 10,636 494
Fig. 3 –Anchor install detail, 5in or 6in pole
Tools Required
•Safety glasses
•Wrenches, 1-1/4” for 4.5m, 6m or 8m (5in/6in) pole
•Wrenches, 1-5/8” for 8m or 9m (5in/7in) pole
•Level
Fig.4-Anchor install detail, 7inpole
LIGHTING LAYOUT RECOMMENDATIONS:
Refer to the product data sheet available at www.landscapeforms.com for
recommendations for light pole spacing.
Installation Guide
Rama Area Light Anchor Kit and Pole
www.landscapeforms.com Ph: 800.521.2546
Date: September 30, 2021
Page 1 of 2
*Calculations per AASHTO 1994, assuming base of the pole is at
grade level, with 90mph fastest mile wind speed with 1.3 gust max.

Included components INSTALLATION PROCEDURE FOR LIGHT POLE:
1. Lift the light pole into position over the installed anchors (refer to Rama anchor kit
installation guide) as shown in Fig. 5. Ensure that the base plate is resting on all four
washers.
2. Install washer and hex nut as shown in Fig. 5.
3. Plumb and level the pole and tighten all anchors.
4. Install luminaire. Refer to separate luminaire installation guide for mounting
luminaire to pole.
5. Install the top cap on the pole (shipped with the pole). If the unit has a twist lock
receptacle, assemble the receptacle and the top cap as shown in Fig. 7 and connect
wiring before installing the top cap. Install provided shorting cap or photo-electric
control.
6. Install the nut covers as shown in Fig. 6.
Tools Required
•Safety glasses
•Wrenches, 1-1/4” for 4.5m, 6m or 8m (5in/6in) pole or 1-5/8” for 8m (5in/7in) or 9m pole
•Wiring tools and connectors
•Proper personnel, crane or lift for hoisting unit onto anchors
•Level
•Dimming control, if required
•Hex keys, 8mm for luminaire, 5/32” for nut covers
•Twist lock photo eye, if required
Landscape Forms is not responsible for site preparation and footings.
CAUTION! This unit is heavy. To avoid injury or damage to the finish, we recommend using
a crane or lift for hoisting the unit onto the anchors.
WARNING! Pole mounted luminaires must be attached either before or immediately after
pole installation. Failure to do so may cause vibration damage to the pole and will void the
pole warranty.
ASSEMBLE WITH CARE! To protect this finish during assembly, place unwrapped powdercoated parts
on packaging foam or other non-marring surface. Do not place or slide powdercoated parts on
concrete or other hard or textured surface –this will damage the finish causing rust to occur. Use
touch-up paint on any gouges in the finish caused by assembly tools.
4X -Nut cover with
1/4-20 x 5/8” button
head cap screw
Twist lock
Receptacle,
optional
Pole cap
Standard For twist lock
Fig. 5 –Install pole
Installation Guide
Rama Area Light Anchor Kit and Pole
www.landscapeforms.com Ph: 800.521.2546
Date: September 30, 2021
Page 2 of 2
Fig. 7 –Install optional twist
lock receptacle to top cap
Shorting cap for
Twist lock,
optional
Fig. 6 –Install nut covers
Pole with base plate
4.5m 6m 8m 8m,
Spiral pattern
9m