SANTA CRUZ SC-916-1 User manual

Santa Cruz Gunlocks LLC. 450 Tyler Rd. Webster, NH 03303 USA
Phone: [phone] • Fax: [phone]
E-mail: [email protected] • Web: www.santacruzgunlocks.com
08/2015
SC-916-1
Fixed Pump Shotgun Rack with SC-1 Lock
1/3
1xSC-1 Gun lock 1xSC-9302 Mounting Hinge
1xSC-1900 Butt Plate
1xSC-9903 L-Bracket
8xSC-8003 Nuts
8xSC-8004 Lock Washers
8xSC-8002 Allen Head Bolt
Components:
Exploded view:
1xSC-1 Gun lock
1xSC-9302 Mounting Hinge
1xSC-1900 Butt Plate
1xSC-9903 L-Bracket
8xSC-8003 Nuts
8xSC-8004 Lock Washers
8xSC-8002 Allen Head Bolt

2/3
1Install Gun Lock
2Install Butt Plate
3Adjust the parts
4Mark the holes
6Tighten the screws
Install gun lock on one leaf of the hinge (part
No. SC-9302) using the 2 screws and lock
washers provided with the SC-1 gun lock.
Install butt plate on L-bracket (butt plate No. SC-
1900 and L-bracket No.SC-9903), as illustrated,
using allen screws and
sheetmetal screws, provided
with the butt plate.
Slightly tighten all bolts and screws so you can
still move parts around. Put your actual weapon
in the gun lock and butt plate and position your
whole assembly at your intended location. Adjust
hinge height/angle and butt plate position until
your weapon is properly lined up.
Important: Weapon must have some (1/16") free
play in gun lock for gun lock mechanism to
operate correctly. Weapon should not press
against gun lock door.
Mark screw locations on wall/oor. Check back
side of wall for fuel or electric lines.
5Drill and install
Place your weapon in the setup, test and retest
your installation by repeatedly inserting and
removing the weapon from the assembly. When
satised, tighten all screws and test again.
B
Note:
Depending on your installation, the
butt plate can be attached directly
onto the oor, using sheetmetal
screws (in case of sheetmetal oor)
or wooden screws (in case of wooden
oor). In this case do not use the L
bracket.
A
SC-916-1
Fixed Pump Shotgun Rack with SC-1 Lock
Drill your holes and install assembly.

3/3
SC-916-1
Fixed Pump Shotgun Rack with SC-1 Lock
Tamper resistant hardware (optional)
Tools needed for installation
Nutdriver
Tape Measure 3/16" Hex Wrench
Ruler
Pencil
Drill
1/2”, 3/4”, 13/16” Wrench
Note:
8xTamper Resistant
Break Away Nut
5/16-18
TT-40 Torx Bit
8xTamper Resistant
Torx Head Bolt
5/16-18
1xTamper Resistant
Torx Head Bolt
1/2-13x3”
1xTamper Resistant
Break Away Nut
1/2-13
TT-55 Torx Bit
Drill bits
5/16", 21/64"
Important
S h o u l d y o u h a v e a n y p r o b l e m i n s t a l l i n g o r u s i n g S a n t a C r u z p r o d u c t s , w e a r e h e r e t o h e l p y o u e v e r y s t e p o f t h e w a y.
Just give us a call at our toll free number [phone] and we will be glad to help you with the installation, special part request or any other way you might need
assistance.
NOTE:
Santa Cruz Gunlocks, LLC (SCG) gun racks and gun locks are intended for temporary, secure storage of rearms. They are not substitutes for a permanent storage
enclosure and only act as limited theft deterrents. And they will not prevent accidental discharge/ring of a chambered round.
To properly and safely use the SCG gun rack and/or gun lock:
- Do not use if your rearm does not t the SCG gun rack and/or gun lock
- Never chamber a round while using a SCG gun rack and/or gun lock
- It is the responsibility of the user to operate the SCG gun rack and/or gun lock properly and safely
WARNING! SAFETY FIRST!
Gun Lock Safety Precautions
Santa Cruz Gunlocks, LLC. (SCG) warrants this product to be free of defects in material and workmanship under normal use for one year from the date of purchase.
SCG makes no other express or implied warranties of the product. The purchaser’s sole and exclusive remedy in the unlikely event of breach of warranty is expressly limited to, at SCG’s election, repair, refurbishment, or
replacement of the defective product with the same version or an upgrade or, if replacement is not possible, a refund of the purchase price.
Shipping cost to SCG must be paid by the user and SCG will pay return shipping charges. Repair parts and replacement products will be provided on an exchange base only and will be either reconditioned or new. This limited
warranty does not cover damage to the product resulting from accident, disaster, misuse, abuse, negligence, improper installation or modication or repair of the product other then by SCG. Limited warranty service may be
obtained by returning the product to SCG. THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Some states, do not allow the exclusion of implied warranties, so their exclusion above may not apply to you.
LIMITATION OF LIABILITY
NEITHER SCG NOR ITS AUTHORIZED DEALER(S) SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE AND STRICT LIABILITY), SUCH AS, BUT NOT LIMITED TO, LOSS OF ANTICIPATED PROFITS OR BENEFITS RESULTING FROM THE USE OR NOT USE OF THE PRODUCT OR ANY BREACH OF ANY WARRANTY, EVEN
IF SCG OR ITS AUTHORIZED REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL SCG OR ITS AUTHORIZED REPRESENTATIVES’ LIABILITY EXCEED THE PRICE PAID FOR THE
PRODUCT.