sanus accents ASF110 User manual

ASF 110
INSTRUCTION MANUAL
Our US-based
install experts
are standing
by to help.
Call us at:
800-359-5520
Or, chat at:
SANUS.com/chatSA
Get it right the
first time.
HeightFinder™
shows you
where to drill.
Check it out at:
SANUS.com/1170
Want to watch
a video that
shows how
easy this DIY
project will be?
Watch it now at:
SANUS.com/363
WE’RE HERE TO HELP

2
35 lb
(15.8 kg)
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before getting started, let’s make sure this mount is perfect for you! Para Español ver página 20
No — Perfect!
Yes — This mount is NOT compatible. Visit MountFinder.Sanus.com or call
1-800-359-5520 to find a compatible mount.
Do you have
all the tools
needed?
1
2
3
4
What is your
wall made of?
Ready to begin?
Does your TV
(including accessories)
weigh more than
35 lb (15.8 kg)?
Drywall with
wood studs?
Solid concrete or
concrete block?
Perfect!
Unsure?
Call Customer Service: 1-800-359-5520
Requires Concrete kit CMK1 (not included)
CAUTION:
DO NOT
install into
drywall alone
Wood Stud Install
Concrete Install
Awl
Pencil Level Stud Finder Screwdriver
Tape
Measure
7/32 in.
(5.5 mm)
Wood
Drill Bit
Electric
Drill Hammer
1/2 in.
(13 mm)
Socket
Wrench Drill Bit
3/8 in.
(10 mm)
Concrete
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use
of this product, contact Customer Service at 1-800-359-5520.
CAUTION: Avoid potential personal injury or property damage!
●This product is designed for use in wood stud, solid concrete, and concrete block walls - DO NOT install into drywall alone
●This product is designed for INDOOR USE ONLY
●The wall must be capable of supporting five times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

3
Before getting started, let’s make sure this mount is perfect for you!
2.95
[75.0]
3.94
[100.0]
2.95
75.0
3.94
100.0
7.87
200.0
7.87
200.0
10.42
264.8
6.40
162.5
16° 16°
0.86
21.9
OFFSET
3.16
80.3
8.50
215.9
3.03
77.0
3° ROLL LEFT
3° ROLL RIGHT
TV INTERFACE
WALL PLATE
FULLY ASSEMBLED MOUNT
TOP VIEW - EXTENDED
TOP VIEW - RETRACTED
SIDE VIEW - EXTENDED
SIDE VIEW - RETRACTED
3-D
in.
[mm]
Dimensions

4
M4 x 8mm
M4 x 12mm
M6 x 12mm
M4 x 35mm
M6 x 35mm
M5 x 12mm M5 x 35mm
M8 x 20mm
M4/M5 M6/M8
NOTE: Not all hardware included will be used.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to
your dealer; contact Customer Service. Never use damaged parts!
Supplied Parts and Hardware
STEP 1 Parts and Hardware
04
05
06
07
08
09
10
x4
x4
x4
x4
x4
x4
x4
TV Screws
Washers
Spacers
11 12
13
x4 x4
x4
22 mm
TV Bracket
Extenders
TV Bracket
TV Bracket
Extender
Screws
02 03 x8
x4
01 x1

5
THIS WAY UP
5/16 x 2 ½ in. 8-32 in.
8-32 x 3⁄8 in.
7/32 in.
5/16 x 2¾ in.
Fischer UX10 x 60R Anchor
STEP 2 Parts and Hardware STEP 3 Hardware
Additional Hardware
Wall Plate
Assembly
Wall Plate Template
14
Lag Bolts
16 x2
x1
15 x1
x1
17 x1
18
Washer
Hex Key
Cable Ties
x1
20
x3
19
Locking Screw
STEP 2B: CONCRETE INSTALLATIONS
Concrete Installation Kit CMK1
[NOT INCLUDED]
Lag Bolt
Concrete Anchor C2 x2
C1 x2
Contact Customer Service at 1-800-359-5520
to inquire about the addition hardware.

6
M4/M5 WASHER
Qty 4
M6/M8 WASHER
Qty 4
SPACER
Qty 4
M4 x 12mm SCREW
Qty 4
M8 x 20mm SCREW
Qty 4
M4 x 35mm SCREW
Qty 4
M5 x 12mm SCREW
Qty 4
M5 x 35mm SCREW
Qty 4
M8 x 35mm SCREW
Qty 4
M6 x 12mm SCREW
Qty 4 M6 x 35mm SCREW
Qty 4
M4/M5 M6
M4 x 12mm
M6 x 12mm
M4 x 35mm
M6 x 35mm
M6 x 20mm
M5 x 12mm
M6 x 12mm
M5 x 35mm
M4 x 8mm
M6 x 14mm
1/4 x 2 ½ in.
A
cm
inches
STEP 1 Attach TV Bracket to TV
These smaller hole patterns only use TV bracket 01 .
Do not use the four TV bracket extenders 02 and eight screws 03 .
75 x 75
100 x 100
01
100
75
100
75
1.1 Measure Your TV Hole Pattern 1.2 Assemble Your TV Bracket
Measure the width and height of your TV hole pattern in mm.
Record your measurements:
Determine which TV bracket configuration to use, A, B, or C
based on your TV hole pattern measurements.
75 mm = 7.5 cm = 3 in.
100 mm = 10 cm = 4 in.
200 mm = 20 cm = 7 7/8 in.
cm
inches
xHeight
Width mm mm
inch dimensions approximate
02
03
Dimensions in mm
TV Hole Pattern
Measurement

7
BC
Assemble TV bracket extenders 02 onto TV bracket 01 as illustrated.
Secure using eight screws 03 in the corner holes shown.
Assemble TV bracket extenders 02 onto TV bracket 01 as illustrated.
Secure using eight screws 03 in the corner holes shown.
200 x 200 200 x 100
01
200
200
200
100
01
02
02
02
02
02
02
02
02
03
03
Dimensions in mm Dimensions in mm
TV Hole Pattern
Measurement TV Hole Pattern
Measurement

8
M5 M6 M8
FLAT BACK ROUND BACK CABLES
Too Short
Correct
Too Long
INSET HOLES
M4
1.3 Select TV Screw Diameter 1.4 Select TV Screw Length
If your TV has a flat back, use the shorter screws.
Spacers and longer screws are supplied to accommodate:
●irregular / round back TVs
●TVs with inset mounting holes
●extra space needed for cables
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M5, M6 or M8) to use.
CAUTION:
Verify adequate thread
engagement with the screw or
screw/spacer combination.
-Too short will not hold the TV.
-Too long will damage the TV.
If your TV included
spacers or wall mount
adapters, see
Troubleshooting
on PAGE 19.

9
Flat Back
Round Back / Extra Space
1.5 Attach TV Bracket
Position your TV bracket configuration over your TV hole pattern - making sure the brackets are vertically centered and level.
Install using either the screw/washer (Flat Back) or screw/washer/spacer (Round Back / Extra Space)combination you selected for your TV.
IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.
13
02
01
04
08
05
09
06 07
10
11
11
12
12
01
NOTE: For 200 x 200 or
200 x 100 hole patterns, you may
need to loosen the screws 03 to
align the bracket extenders 02 .
After bracket extenders 02 are
secured to the back of your TV,
re-tighten screws 03 .
TV Bracket Configurations Band C
(from page 7)
Configuration B Illustrated, with spacers
TV Bracket Configuration A
(from page 6)
Illustrated with spacers

10
1. Locate your stud. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.
2. Position the wall plate template 14 at your desired height and line up the holes with your stud center line. Level the template and tape in place.
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. Remove wall plate template 14 .
IMPORTANT: Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth of 2½ in. (63.5 mm).
THIS WAYUP
THIS WAYUP
STEP 2A Attach Wall Plate Wood Stud Installation
THIS WAY UP
THIS WAY UP
2
THIS WAYUP
THIS WAYUP
3
14 14
≤ 16 mm
(5/8 in.)
1
NOTE: TV shifts 21.9 mm (7/8 in.) to the right
or left when in the home position. Consider this when
selecting the location of your wall mount.
CAUTION: Avoid potential personal injury or property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½x 3 ½in. (38 x 89 mm)
2½in. (63.5 mm)
7/32 in.
(5.5 mm)

11
Wood Stud Installation
THIS WAYUP
THIS WAY UP
54 6
15
16
15
4. Slide the cover to expose the mounting holes in wall plate assembly 15 .
5. Install wall plate assembly 15 using two lag bolts 16 . Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
6. Reattach the cover onto the wall plate assembly 15 .
Cover Cover
Tighten
Loosen
16
NOTE: If needed, you can make small level adjustments to the wall plate by loosening the bottom lag bolt 16
and shifting the wall plate until level. Tighten the bottom lag bolt when adjustments are complete.
15
THIS WAY UP
THIS WAY UP

12
1. Position the wall plate template 14 on the wall at your desired height. Level the wall plate template and mark the hole locations.
2. Drill two pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.
3. Remove the wall plate template 14 and insert two anchors C2
(Fischer UX10 x 60R- included in the Concrete Installation Kit CMK1).
CAUTION: Be sure the anchors C2 are seated flush with the concrete surface.
THIS WAYUP
THIS WAYUP
STEP 2B Attach Wall Plate Solid Concrete / Concrete Block Installation
THIS WAYUP
THIS WAYUP
2
THIS WAYUP
THIS WAYUP
3
14
14
1
NOTE: TV shifts 21.9 mm (7/8 in.) to the right
or left when in the home position. Consider this when
selecting the location of your wall mount.
Concrete Installation Kit CMK1 is not included
Contact Customer Service at 1-800-359-5520
to inquire about the additional hardware.
CAUTION: Avoid potential personal injury or property damage!
●Mount wall plate assembly 15 directly onto concrete surface (no wall covering)
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
3/8 in.
(10 mm)
3 in. (75 mm)
C2

13
Solid Concrete / Concrete Block Installation
THIS WAYUP
THIS WAYUP
54 6
15
15
4. Slide the cover to expose the mounting holes in wall plate assembly 15 .
5. Install wall plate assembly 15 using two lag bolts C1 . Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt C1 . DO NOT over-tighten the lag bolts.
6. Reattach the cover onto the wall plate assembly 15 .
Cover Cover
Tighten
Loosen
NOTE: If needed, you can make small level adjustments to the wall plate by loosening the bottom lag bolt
C1 and shifting the wall plate until level. Tighten the bottom lag bolt when adjustments are complete.
15
THIS WAY UP
THIS WAY UP
C1
C1

14
3
2
1
HEAVY! You may need assistance with this step.
STEP 3 Hang TV onto Wall Plate
1. Position the arm of wall plate assembly 15 so the elbow is bent 90 degrees and pressed against the wall.
2. Hang the TV onto the arm of wall plate assembly 15 by first hooking the top support, then resting the TV into place.
3. Lock the TV to the wall plate assembly 15 with locking screw 17 and washer 18 .
CAUTION: Avoid potential personal injuries and property damage! This locking screw 17 must be installed to secure the TV onto
the wall plate assembly 15 .
18
17
15
15 15
Top Support

15
Manage Cables
If desired, thread the supplied cable tie 19 through the loop provided on the arm of the wall plate assembly 15 , and secure your TV cables
along the arm for a clean look.
IMPORTANT: Fully extend the arm of wall plate assembly 15 to ensure you have enough slack in the cables for full TV movement.
19
15

16
TV Adjustments
TILT ADJUSTMENT
Your TV should adjust easily when moved, then stay in place.
If your TV is too loose or too tight, adjust the tilt tension
knob by hand.
NOTE: Once your TV is in place, tighten the tilt tension
knob to prevent unwanted movement.
LEVEL ADJUSTMENT
To adjust the leveling of your TV, loosen the locking screw 17 , level
your TV, then tighten locking screw 17 .
IMPORTANT: This locking screw 17 must be installed to secure
the TV onto the wall plate assembly 15 .
Tighten
Loosen 17
Tilt Tension Knob
Tighten
Loosen

17
Arm Tension
Screw
14 mm (9/16 in.)
socket
REMOVING THE TV
To remove your TV from the
wall plate assembly 15 ,
disconnect all cables and then
reverse the
procedures in STEP 3.
SWIVEL ADJUSTMENT
Your TV should adjust easily when moved,
then stay in place.
If your TV is too loose or too tight, adjust
the arm tension screws using hex key 20
and a 14 mm (9/16 in.) socket.
EXTENSION/RETRACTION ADJUSTMENT
Your TV should adjust easily when moved,
then stay in place.
If your TV is too loose or too tight, adjust
the arm tension screws using hex key 20 .
15
20
Arm Tension
Screw
20
Loosen
Loosen
Tighten Tighten
HEAVY! You may need
assistance with this step.

18
Features
Fully articulating arm with 3
pivot points creates optimal
viewing positions
TV tilts up or down for the
perfect viewing angle
Cable tie hook
holds cables
along mount arm
for a clean look
Level
adjustments
create a
worry-free
installation
Adjustments allow fingertip control
of TV or restriction of TV movement
TV bracket expands
to fit TV hole patterns
from 75 x 75 mm up to
200 x 200 mm

19
Troubleshooting
TV Supplied
Spacer TV Supplied
Spacer
TV supplied spacers
CAUTION: Avoid potential injury or property damage!
Use the correct screw length for adequate thread engagment.
CAUTION: Avoid potential injury or property damage!
Use the correct screw length for adequate thread engagment.
TV Supplied
Spacers
ab
FLAT BACK ROUND BACK CABLES
a:Use your TV supplied spacer for flat back TVs (AND you want
your TV closer to the wall).
b:Use your TV supplied spacer and spacer 13 for:
●Round (irregular) back TVs ●Extra space needed for cables
– Too short will
not hold the TV.
– Too long will
damage the TV.
– Too short will
not hold the TV.
– Too long will
damage the TV.
Too Short Too Short Too Long Too Long
Correct Correct
13
NOTE: The M8x20mm screw will not work with the TV supplied
spacer. Verify with your TV manual that you can use the M8x20mm
screws without the TV supplied spacer.
NOTE: The M8x20mm screw will not work with the TV supplied spacer
or spacer 13 . Verify with your TV manual that you can use the M8x20mm
screws without the TV supplied spacer.
If you are uncertain about your hardware selection,
contactCustomer Service at 1-800-359-5520.

20
(15.8 kg)
35 libras
Antes de comenzar, verifiquemos que este soporte sea el ideal para sus necesidades.
INSTRUCCIONES DE SEGURIDAD IMPORTANTES. CONSÉRVELAS. LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO.
No — ¡Perfecto!
Sí — Este soporte NO es compatible. Visite MountFinder.Sanus.com o llame al
1-800-359-5520 para encontrar un soporte compatible.
¿Su televisor pesa
más de 15.8 kg (35
libras), incluidos
los accesorios?
¿Tiene
todas las
herramientas
necesarias?
1
2
3
4
¿De qué está
hecha su pared?
¿Listo para
comenzar?
5,5 mm
(7/32'')
Madera
10 mm
(3/8'')
Hormigón
Lea estas instrucciones en su totalidad para estar seguro de sentirse cómodo con este fácil proceso de instalación. Consulte
también el manual del usuario de su televisor para ver si existe algún requisito especial para instalar su televisor en la pared.
Si no entiende las instrucciones o si tiene dudas acerca de la seguridad de la instalación, del ensamblado o del uso del
producto, póngase en contacto con el servicio de atención al cliente al 1-800-359-5520.
13 mm
(1/2”)
¿Tabiques
de yeso con
montantes de
madera?
¡Perfecto!
DestornilladorCinta métrica Broca Broca
Taladro
eléctrico MartilloLlave de tubo PunzónLápiz Nivel Localizador
de montantes
PRECAUCIÓN:
NO lo instale
en tabiques
únicamente
de yeso
Paredes con
montantes de madera
paredes con de
hormigón
¿Hormigón sólido
o bloques de
cemento?
Llame al 1-800-359-5520
Concrete kit CMK1 (not included)
¿No está
seguro?
PRECAUCIÓN: Evite posibles lesiones personales y daños materiales.
●Este producto incluye instrucciones y elementos de sujeción para su instalación en paredes con montantes de madera,
en superficies de hormigón y sobre bloques de cemento. NO lo instale en tabiques únicamente de yeso.
●Este producto está diseñado para USO EN EL INTERIOR SOLAMENTE
●La pared debe soportar cinco veces el peso del televisor y del soporte juntos.
●No utilice este producto para ningún otro propósito que no sea el explícitamente especificado por el fabricante.
●El fabricante no se responsabiliza por ningún daño o lesión resultante del montaje incorrecto o de uso indebido.
ESPAÑOL