Sanyo VPC-S885 User manual

INSTRUCTION MANUAL
Digital Camera
Please read these instructions carefully before using the camera.
Keep this manual in a safe place for later reference.

EN-1
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of
the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the manual. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail),
restart the application or disconnect and connect the communication cable (USB, etc.)
again.

EN-2
READ THIS FIRST
Trademark Information
 Microsoft
®
and Windows
®
are U.S. registered trademarks of Microsoft Corporation.
Pentium®is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Inc.
SD™ is a trademark.
SDHC™ is a trademark.
Other names and products may be trademarks or registered trademarks of their
respective owners.
Product Information
Product design and specifications are subject to change without notice. This
includes primary product specifications, software, software drivers, and user’s
manual. This User Manual is a general reference guide for the product.
The product and accessories that come with your Camera may be different from
those described in this manual. This is due to the fact that different retailers often
specify slightly different product inclusions and accessories to suit their market
requirements, customer demographics, and geographical preferences. Products
very often vary between retailers especially with accessories such as batteries,
chargers, AC adapters, memory cards, cables, pouches, and language support.
Occasionally a retailer will specify a unique product color, appearance, and internal
memory capacity. Contact your dealer for precise product definition and included
accessories.
The illustrations in this manual are for the purpose of explanation and may differ
from the actual design of your Camera.
The manufacturer assumes no liability for any errors or discrepancies in this user
manual.

EN-3
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the Camera, turn the power off
and remove the batteries.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the Camera has fallen or its case has been damaged, turn the power
off and remove the batteries.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the Camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Do not use the Camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow,
on the beach, or near the shore.
Do not place the Camera on inclined or unstable surfaces.
This might cause the Camera to fall or tilt over, causing damage.
Keep the batteries out of the reach of children.
Swallowing the batteries might cause poisoning. If the batteries are
accidentally swallowed, immediately consult a physician.
Do not use the Camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
Please use batteries with complete external seals.
Do not use batteries from which the seals have been damaged or removed.
This may cause leakage, explosion, or injury.

EN-4
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to
leak. If the internal fluid enters your eyes or comes into contact with your
body or clothes, rinse with fresh water. If the internal fluid has entered your
eyes, consult a physician to receive treatment.
Camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the Camera.
This might cause damage to the Camera.
Do not use the Camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous
use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the Camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the Camera in a well-ventilated place.
Do not leave the Camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the Camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and
electric shock.

EN-5
Warning:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
FOR AMERICAN USERS
The following advisory is included in accordance with the laws of the State of California
(USA):
WARNING:
This product contains chemicals, including lead, known to the States of California to
cause cancer, birth defects or other reproductive harm. Wash hands after handling.
 This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designated to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
 Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

EN-6
FOR CANADIAN USERS
 This Class B digital apparatus complies with Canadian ICES-003
FOR EU USERS
The symbol mark and recycling systems described below apply to
EU countries and do not apply to countries in other areas of the
world.
Your SANYO product is designed and manufactured with high
quality materials and components which can be recycled and/or
reused.
The symbol mark means that electrical and electronic equipment,
batteries and accumulators, at their end-of-life, should be disposed
of separately from your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this
chemical symbol means that the battery or accumulator contains a
heavy metal at a certain concentration.
This will be indicated as follows: Hg: mercury, Cd: cadmium, Pb:
lead
In the European Union there are separate collection systems for
used electrical and electronic equipment, batteries and
accumulators.
Please, dispose of them correctly at your local community waste
collection/recycling centre.
Please, help us to conserve the environment we live in!
Manufacturer and Address
SANYO Electric Co., Ltd.
5-5, Keihan-hondori, 2-chome,
Moriguchi City, Osaka, Japan
Authorized Representative and Address
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 Munich, Germany

EN-7
Symbols used in this manual
 Points giving some extended instructions or special points to pay attention to.
You many find the answers to questions or problems concerning camera operation in
the sections “Troubleshooting”.
This class B digital apparatus complies with Canadian ICES-003.
FCC information
Tested To Co m p l y
With FCC Standards
FOR HOME OR OFFICE USE
Model number: VPC-S885
Trade Name: SANYO
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street
Chatsworth, California 91311
Telephone No.: [phone]
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Declaration of Conformity
Canadian ICES-003 information

EN-8
Notes on Battery Usage
When you use the batteries, carefully read and strictly observe the Safety Instructions
and the notes described below:
Use only the specified batteries.
Avoid extremely cold environments as low temperatures can shorten the battery life
and reduce Camera performance. Therefore Ni-MH rechargeable batteries are
highly recommended.
When you are using a new rechargeable batteries or rechargeable batteries that
have not been used for an extended period of time (the batteries that passed the
expiry date are exception), it may affect the number of images that can be captured.
Therefore, to maximize their performance and lifetime, we recommend that you fully
charge the batteries and discharge them for at least one complete cycle before use.
The batteries may feel warm after a long period of continuous use of the Camera or
the flash. This is normal and not a malfunction.
The Camera may feel warm after a long period of continuous use. This is normal
and not a malfunction.
If the batteries are not to be used for a long period of time, remove them from the
Camera to prevent leakage or corrosion and store them after no battery power is left.
Stored for a long time in a fully charged condition, their performance may be
impaired.
Always keep the battery terminals clean.
There is a risk of explosion if the batteries are replaced by an incorrect type.
Dispose of used batteries according to the recycle instructions.
Charge the rechargeable batteries fully before using for the first time.
Never use batteries of different types (together) or mix old and new batteries.
Never use manganese batteries.
To prevent short-circuiting or fire, keep the batteries away from other metal objects
when carrying or storing.

CONTENTS
EN-9
10 INTRODUCTION
10 Overview
10 Package Contents
11 GETTING TO KNOW YOUR
CAMERA
11 Front View
12 Rear View
13 LCD Monitor Display
15 GETTING STARTED
15 Preparation
16 Initial Settings
18 CAPTURE MODE
18 Capturing Images
19 Setting the Scene Mode
21 Setting the Panorama Mode
22 Taking Images When the Smile
Feature Is On
23 Recording Shots into Multiple Image
Layout
23 Recording Shots using Face
Detection Technology
24 VIDEO MODE
24 Recording Video Clips
24 Playing Back Video Clips
25 PLAYBACK MODE
25 Playing Back Still Images
26 Thumbnail Display
26 Removing Red-eye
27 Attaching Voice Memos
28 Protecting Images
29 Erasing Images
30 MENU OPTIONS
30 Capture Menu
33 Video Menu
34 Playback Menu
35 Setup Menu
37 TRANSFERRING FILES TO
YOUR COMPUTER
37 Downloading Your Files
38 EDITING SOFTWARE
INSTALLATION
39 SPECIFICATIONS
40 APPENDIX
40 Possible Number of Shots
41 Troubleshooting
42 Connecting to a PictBridge Compliant
Printer

EN-10
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art smart
camera. Equipped with a 8.1-megapixel CCD, this camera is capable of capturing
images with a resolution of up to 3264 x 2448 pixels.
Package Contents
Carefully unpack your camera and ensure that you have the following items:
Common Product Components:
Digital Camera
Instruction manual
Software CD-ROM
USB cable
Camera strap
Camera pouch
2 x AA size batteries
Optional Accessory:
SD/SDHC memory card
Accessories and components may vary by retailer.

EN-11
GETTING TO KNOW YOUR CAMERA
Front View
1. Shutter button
2. ON/OFF Power button
3. Flash
4. Self-timer LED
5. Self-portrait mirror
6. USB terminal
7. Microphone
8. Lens
7
1 2 3 45
6
8

EN-12
Rear View
Item Function
Capture Mode Video Mode Playback Mode
1. Shutter button Record button Still image: to capture mode
Video clip: to video mode
2. :Zooms out
:Zooms in
:Zooms out
:Zooms in
:Thumbnail
:Zooms in
3. Playback mode Playback mode Still image: to capture mode
Video clip: to video mode
4.
Capture menu Video menu Playback menu
5. Compensation
>-- Previous image
6. Self-timer Self-timer --
7. Flash -- Next image
8. If any scene mode is set:
switches to scene mode
selection screen --
Still image: to display image
Records voice memo ( if
“Voice Memo” is “On”).
Video clip: to play video clip
9. Focus Focus --
10. -- -- Delete
11. Switches to:
Video mode > Scene
mode selection screen
Switches to:
Scene mode selection
screen> Capture mode
Still image: to capture mode
Video clip: to video mode
b
a

EN-13
LCD Monitor Display
Capture mode
1. Zoom status
2. Battery condition
[l] Full battery power
[o] Medium battery power
[n] Low battery power
[m] No battery power
3. Flash mode
[Blank] Auto
[a] Flash On
[d] Flash Off
[c] Red-eye
[`] Slow Sync
[_] Pre-flash
4. Storage media
[ ] Internal memory (no card)
[ ] SD/SDHC memory card
5. [ ] Histogram
6. Main focus area
7. Image quality
[ ] Fine
[ ] Standard
[ ] Economy
8. Image size resolution
[ ] 3264 x 2448
[ ] 2816 x 2112
[ ] 2304 x 1728
[ ] 1600 x 1200
[ ] 640 x 480
9. Available number of shots
10. ISO
[Blank] Auto
[ ] ISO 64
[ ] ISO 100
[ ] ISO 200
[ ] ISO 400
[ ] ISO 800
[ ] ISO 1600
11. Self-timer icon
[f] 2 sec.
[g] 10 sec.
[h] 10+2 sec.
12. Date and time
13. [ ] Exposure compensation
[ ] Backlight correction
(Adjust exposure value with the e/ f
buttons)
14. Capture mode icon
[Blank] Single
[ ] Continuous
[ ] AEB (Auto Exposure Bracketing)
[ ] Album Shot
15. Slow shutter warning
16. White balance
[Blank] Auto
[ ] Incand.
[ ] Fluoresc.1
[ ] Fluoresc.2
[ ] Daylight
[ ] Cloudy
[ ] Manual WB
17. Focus setting
[Blank] Auto
[ ] Face Detect
[ ] Macro
[ ] Infinity
18. Mode icon / Scene mode
[ ] Auto
[ ] Smile Detection
[ ] Anti-shake
[ ] Panorama
[ ] Portrait Man
[ ] Portrait Lady
[ ] Landscape
[]Sports
[ ] Night Portrait
[ ] Night Scene
[ ] Candlelight
[ ] Fireworks
[]Text
[ ] Sunset
[ ] Sunrise
[ ] Splash Water
[ ] Flow Water
[ ] Snow
[ ] Beach
[]Pets
[ ] Natural Green
[ ] Program AE
1 2
9101112
3
4
5
6
7
8
13
14
15
16
17
18
P

EN-14
Video mode
1. Zoom status
2. Flash mode
3. Battery condition
4. Storage media
5. Main focus area
6. Video quality
7. Video resolution
8. Available recording time/Elapsed time
9. Self-timer icon
10. Date and time
11. Focus setting
12. Mode icon
13. Sound off icon
Playback mode - Still image playback
1. Voice memo
2. Battery condition
3. Storage media
4. Histogram
5. Image quality
6. ISO
7. Image size resolution
8. File number
9. Folder number
10. Date and time
11. Exposure value
12. Aperture value
13.Shutter speed value
14. Protect icon
15. Mode icon
Playback mode - Video playback
1. Video status bar
2. Elapsed time
3. File number
4. Folder number
5. Sound off icon (When the c button is pressed
during video playback)
You cannot play sounds because the
camera does not support the speaker
function. Please use PC or other media to
play the videos/still images with sounds.
6. Play mode
7. Mode icon
8. Total recorded time
1 2 3
8910
4
5
6
7
11
12
E
100- 0001
100- 0001
:Play
:Play
10
11
12
13
14
15
1 2
6
9 8
3
4
7
5
R
100 - 0001
100 - 0001
100 - 0001
Total
Total
00 : 00 : 08
00 : 00 : 08
00 : 00 : 08
Play
Play
00 : 00 : 01
00 : 00 : 01
00 : 00 : 01
E
1
6
7
5
4 3
2
8
q
q
q
E
E

EN-15
GETTING STARTED
Preparation
1. Attach the camera strap.
2. Open the battery/memory card cover.
3. Insert the supplied batteries with correct orientation as
shown.
4. Insert an SD/SDHC memory card (Optional).
 The camera has 32MB internal me mory (26M B
available for image storage) , but you can load an
SD/SDHC memory card to expand the camera’s
memory capacity.
Be sure to format the memory card with this
camera before its initial usage.
5. Close the battery/memory card cover and make sure it is
locked securely.
 To prevent valuable data from being accidentally erased from
an
SD/SDHC memory card , you can slide the write protect tab
(on the side of the SD/SDHC memory card) to “LOCK”.
To save, edit, or erase data on an SD/SDHC memory card,
you must unlock the card.
To prevent damaging of an SD/SDHC memory card, be sure
to turn off the power when inserting or removing the SD/
SDHC memory card. If inserting or removing the SD/SDHC
memory card with the power on, the camera will automatically turn off.

EN-16
Initial Settings
Setting the Date and Time
The date/time needs to be set if and when:
The camera is turned on for the first time.
The camera is turned on after leaving the camera without the batteries for an
extended period of time.
When the date and time information is not displayed on the LCD monitor, follow these
steps to set the correct date and time.
1. Press the button, and set the camera
mode to [ ] or [ ]; or press the button .
2. Press the button.
3. Select [Setup] with the fbutton.
4. Select [Date/Time] with the c/ dbuttons, and
press the button.
5. Select the date format with the c/ dbuttons,
and press the button.
Select the item’s field with the e/ fbuttons
and adjust the value for the date and time
with the c/ dbuttons.
 The time is displayed in 24-hour format.
 After confirming all settings are correct, press
the button .
6. To exit from the [Setup] menu, press the
button.

EN-17
Choosing the Language
Specify in which language menus and messages are to be displayed on the LCD monitor.
1. Press the button, and set the camera
mode to [ ] or [ ]; or press the button.
2. Press the button.
3. Select [Setup] menu with the fbutton.
4. Select [Language] with the c / d buttons and press
the button .
5. Select the displayed language with the c / d
buttons and press the button .
The setting will be stored.
6. To exit from the [Setup] menu, press the
button.
Formatting the Memory Card or Internal Memory
This utility formats the memory card (or internal memory) and erases all stored images
and data.
1. Press the button, and set the camera
mode to [ ] or [ ]; or press the button .
2. Press the button.
3. Select [Setup] menu with fbutton.
4. Select [Format] with the c / d buttons, then
press the button .
5. Select [Execute] with the c / d buttons, and
press the button .
 To cancel formatting, select [Cancel] and
press the button .
6. To exit from the [Setup] menu, press the
button.

EN-18
CAPTURE MODE
Capturing Images
Your camera is equipped with a 2.4" full color TFT LCD monitor to help you compose
images, playback recorded images/video clips or adjust menu settings.
1. Press the button to turn the power on.
The status LED lights green and the camera is initiated.
2. Press the button, and set the camera mode to [ ].
3. Compose your image in the LCD monitor.
Pressing the button zooms in on the subject, and enlarges the subject on the
LCD monitor.
Pressing the button zooms out on the subject, and provides a wider angle
image.
4. Press the shutter button.
 Pressing the shutter button down halfway
automatically focuses and adjusts the
exposure, and pressing the shutter button
down fully captures the image.
The focus area frame turns green when
the camera is in focus and the exposure is
calculated.
When the focus is not suitable, the frame
of the focus area turns red.

EN-19
Setting the Scene Mode
By simply selecting one of the available 21 scene modes, you can capture the image
with the most appropriate settings.
1. Press the button until the scene mode
selection screen appears.
2. Select the desired scene mode with the e/ f
buttons, and press the button.
3. Compose the image and press the shutter
button.
The table below will help you choose the appropriate scene mode:
Scene mode Description
Smile Detection Select this mode to automatically capture an image when a smiling
face is detected.
Anti-shake This mode minimizes the influences of hand shaking when you
want to capture an image.
Panorama Select this mode when you want to capture a series of shots then
stitch them together with software to make a single photo on the
computer.
Portrait Man Select this mode when you want to capture an image that makes a
man stand out against a blurred background.
Portrait Lady Select this mode when you want to capture an image that makes a
lady stand out against a blurred background.
Landscape Select this mode when you want to capture an image with infinity
focus, hard sharpness and high saturation.
Sports Select this mode when you want to capture fast-moving subjects.
Night Portrait Select this mode when you want to capture people with an evening
or night scene background.
!