Satco STARFISH 65/900 Manual

1© Copyright 2022 Satco Products, Inc. 7/22, v2.1
LED SMART SECURITY FLOODLIGHT
& CAMERA
Models: 65/900, 65/901, 65/902
Satco Products, Inc.
Brentwood, NY 11717
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
Thank you for choosing our Starsh Security Floodlight with Camera.
Getting started is easy.
1. Parts Included
WARNING: Risk of Fire or Electric Shock.
• This xture must be wired in accordance with the National Electrical Code and applicable local codes and ordinances.
Proper grounding is required to insure personal safety. Carefully observe grounding procedure under installation section.
• Make certain power is OFF before starting installation or attempting any maintenance. Risk of re/electric shock. If not
qualied, consult an electrician.
• For proper weatherproof function, all gaskets must be seated properly and all screws inserted and tightened rmly. Apply
weatherproof silicone sealant around the edge of the Back Box and/or Junction Box. This is especially important with an
uneven wall surface. Silicone all plugs and unused conduit entries.
• Be sure xture temperature is cool enough to touch. Do not clean or maintain while xture is energized. Clean glass lens
with non-abrasive glass cleaning solution. Do not open xture to clean the LED. Do not touch the LED.
2. Product Details
3. Safety Instructions
Security Flood
Camera
Gasket
M4*14 Bracket
Screws
Wire Nuts
1900 Lm Output
Light Lock Collar
Microphone
Lens
LED Indicator
Speaker
PIR Motion Detector
LED Bullet Head
Adjustment Locknut
Camera Lock Collar
Micro SD Card Slot
Reset
WIRING: If wiring does not include a ground wire, consult your local electrical code for approved grounding methods.
For proper connection, place wire nut over wires and twist clockwise until tight.

2© Copyright 2022 Satco Products, Inc. 7/22, v2.1
4. Optimal Installation Height
The best installation height is around
2.5M or 8ft, which will optimize the motion
sensor performance.
STEP 1: Disconnect power supply.
Remove (2) plastic plugs. Remove
inserted screws and mounting plate.
STEP 4: Secure xture onto mounting
plate with screws and plastic plugs.
STEP 2: Drill (2) holes on the wall and
insert expansion screws. Attach gasket
and x mounting plate with screws.
STEP 5: Check xture and connect
power supply.
STEP 3: Connect the wires,
refer to the Wiring Diagram.
5. Installation
For installation in Wall Mount or Eaves Mount Recessed Junction Box Applications.
6. Turn ON Power at the Breaker
Motion
Detection
Zone
Up to 10m (32ft) 1m (3.28ft) 2.5m (8ft)
Mounting Plate
(2) M5*12
Screw
Gasket
(2) M4*14
Screw
L
N
G
L
N
G
Wiring Diagram
L
(Black)
N
(White)
N
(White)
L
(Black) G
(Yellow & Green)
G
(Yellow & Green)
Input Output
After connecting power supply, the lights will turn on and your Starsh Security Floodlight Camera will make a sound to
indicate that it’s in pairing mode.
TROUBLESHOOTING
1. Check your power source.
2. Check electrical connections.
3. Check that the motion sensor is working properly.
Mounting
Plate
(2) Plastic
Plugs

3© Copyright 2022 Satco Products, Inc. 7/22, v2.1
7. Connection Preparation
Please install the Starsh Security Floodlight Camera in an area that has adequate Wi-Fi signal to ensure the best
product performance.
Download the Starsh APP and set up your account
from the Apple App Store or Google Play Store.
You can also scan the QR Code below.
NOTE: The switch must remain in the ON position to
function properly.
• Power the device on and make sure the
indicator is red and flashing quickly or a
prompt tone is heard.
• If the indicator is not quickly ashing red,
press the reset button on the back of the
camera for 5 seconds, and then release.
The red LED should begin to blink.
• Follow App’s instructions to complete
network pairing process, the device will
connect to your Wi-Fi network successfully.
• Once the blue LED light is on, the camera
is successfully paired and ready to be used.
Launch the app from your smartphone
and click to register and then sign in.
Follow the on-screen instructions.
NOTE: Please refer to Starsh User Guide for detailed product pairing instructions. This product requires a 2.4GHz Wi-Fi
connection for proper operation.
Router
Camera Smartphone
8. Get the APP and Account
9. If the Security Floodlight is controlled by an in-wall switch, move the switch to the
ON position
10. Set Up the Camera
Red light
blinks
In the back of the camera, press the
Reset button for about 5 seconds to
start Reset processing.

4© Copyright 2022 Satco Products, Inc. 7/22, v2.1
11. Micro SD Card
• The camera includes a 32GB Micro SD Card that is pre-formatted.
• This camera is capable of using up to a 128GB Micro SD Card
for additional storage. To ensure the Micro SD Card can record
properly. We recommend a Class 10 or higher speed Micro SD
Card.
• The Micro SD Card must be formatted to FAT32, if that is not the
default formatting.
• Only insert or remove the SD card when power is removed from
the device, or else there is a risk of le corruption.
12. APP Details
You’re done! Congratulations, your camera is ready to use.
Micro
SD
Alarm Manually Active the Floodlight Alarm
Full Screen Switch Live View to Full Screen
History Review all past video
Light Manually Turn the Floodlights On/Off
Motion Notications Enable/Disable Motion Notications
Mute Mute/Unmute the Floodlight Microphone
Night Vision Set Night Vision to Auto/On/Off
Notications Review past Motion Notications
Picture in Picture See Live View outside of APP
PIR Settings Adjust PIR Sensitivity & Light On Time
Private Mode Remotely Enable/Disable Camera Recording
Record Record the Live View to Mobile Device
Resolution Set between HD/SD
Screenshot Screenshot the Live View to Mobile Device
Settings Main Settings
Talk Speak through the Floodlight Speaker
Zoom Zoom in on the Live View
Settings
Zoom
Private Mode
Motion Notications
Record
Light
Night Mode
Mute
Resolution
Full Screen
Alarm
PIR Settings
Screenshot
Talk
Notications History
Picture in Picture

5© Copyright 2022 Satco Products, Inc. 7/22, v2.1
APPENDIX: Camera LED Guide
All trademarks are used for reference purposes only.
Thanks again for choosing our Floodlight camera. Make life safe in your hands. Boost security mobility in your smartphone.
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (5) years
from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application.
The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color
and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units
must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt
showing date of purchase.
Call 1-866-994-4148 to obtain a return authorization number and an address where to ship your defective product.
NOTE: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the
defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is
caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury
which is (1) to person or property or otherwise; (2) incidental or consequential in nature; (3) based upon theories of warranty,
contract, negligence, strict liability, tort, or otherwise; or (4) directly, or indirectly related to the sale, use, or repair of the
product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
FAQ:
5-YEAR WARRANTY
1. Do the oodlights turn on automatically?
These oodlights have been designed to trigger based on motion in the designated areas, when it is dark outside.
2. Can you upgrade the SD Card to a larger size?
Yes, this oodlight is capable of using up to a 128GB MicroSD card. We recommend at least a Class 10 MicroSD card
for best performance.
3. How do you view the camera feed?
After pairing, simply open the app and select the Floodlight that you would like to view. Make sure that the camera is
within range of your Wi-Fi router for best performance.
4. When do I get alerts?
This oodlight can provide alerts to notify you when there is motion in a designated area. You can adjust the sensitivity
and motion zone to increase or decrease the number of recordings. You can also turn motion alerts on or off, or even
set the time of day that they will be sent to your phone.
For more questions, please send from the APP “Settings” – “FAQ & Feedback”
NO. LED Status Camera Status
1 Red LED on System starting up
2 Red LED blinks Standby for conguration
3 Blue LED blinks Network pairing
4 Blue LED on Camera online

USER GUIDE
START HERE
DOWNLOAD
THE
STARFISH
APP
System Requirements
Minimum iOS 9.3 or Wi-Fi 4.4
• Dedicated 2.4GHz Wi-Fi Network •
TECHNICAL SUPPORT
Support@satcostarsh.com
1
0
0
0
•• 0 ••
•• 0 ..
0 • 0 • 0
ooo • • ooo
OQ 00
••• • ••
... o.o ...
0 • 0
0 • 0
0 • 0
0 • 0
0 • 0
STARFISH™
•
live life enUghtened
llllllii.... GET IT ON
,,.... Google Play

Create a Password then tap “Done”
4
Launch the App and tap “Register” for new accounts
or “Login” for existing accounts.
Enter E-Mail address, then tap “Get verication code”.
2
3
,JI f1Zlli'i LU
<
!Register
lki" ed st tes of America
<
Set Password

Create a Home
Create/Share
a Home
Tap the "Me" button on the bottom of the screen,
and then tap "Home Management". Tap the "Create
a home" button to setup your home.
5
IJ Mere Sefvice5l
® SeJ ' gs
H
C.mc::, II create a
home
Home LocadOf'I
SATCO ~
IEdgawo ~Heartland IBM:11
L.iiJlngRoom
Se<:o!ld BedIOom

Share a Home
From the Home Management screen, select the Home
that you would like to share.
Tap "Add Member" and select the way that you would
like to send the invitation
6
Enter the user information and select if the new member
will be an "Administrator" or a "Common Member" in
the Home. Tap "Save" to send the invitation
7
johnsmith
[email protected]
ill
I
ritoo L T[
<
SA T CO
- cl M mber
.11 I ill1 L J[
N I
n
ounl
8: ,.,..
Hom Manag@ffl 11 1
8: 22AM
A<dd Momber
ni t ed States o Amer i

Tap the (+) button on the top right corner to access
the action menu, then select "Add Device".
8
Add Devices
First make sure your phone is connected to a 2.4GHz
Wi-Fi Network, then select the type of device you
would like to connect. If you have a BLE enabled
device, make sure that you have Bluetooth turned ON
for connection.
If your device is BLE enabled, you may see a pop-up
indicating that there are unpaired devices in the
area. Click "Add" and select the devices you would
like to connect.
9
'\ I II
. ... o ··· . ...
- 1 . -
1 ;/f ·_ '
t' I
S F
+
Clear
Add IDevfoe
I Sc n
~ p
Dev, 11:e!;ii tg , be added ;1
Dll!lnal dd Ga ' iO cl'd

Enter your 2.4GHz Wi-Fi Network name and
password, and click "Next".
10
11
Note: If the devices are not ashing, turn devices On
and Off 5 times to enter pairing mode.
Ensure that your Starsh device is installed and
powered ON.
Put the Device into pairing mode by turning OFF
and then ON 5 times. Please wait about 3 seconds
between switching OFF and ON each time.
For pairing strings, strips, switches, plugs or
controllers, hold the power button for approximately
10 seconds until indicator starts blinking.
Cancel
Select 2.4 GHz Wi - Fi !Network
.a d enter password.
.,,; -F - 2.. 4G hz
8 P rnd

If correctly put into pairing mode, the device will be
blinking quickly. Conrm that the device is blinking
quickly and click "next". The pairing status screen
will appear.
12
To rename the device, tap the “Pen” icon, enter the
new name and tap “Completed”. The device is now
ready to be controlled with the starsh App.
13
Note: If unsuccessful, please refer to the FAQs on
Satco.com/Starsh
I Reset the, device first. Adtlilfl device.•.
i,. jiOW'Cfll(I 111'1
Ad d.
5 rf15.h 9.5W Sme b.J

Individual Bulb On/Off
Individual Bulb Setting
Features
Tap the Power Button to turn the device On or Off
Tap the device icon for additional device features
14
15
Si rfl h9.5W Sm r l:lu 3
S r -sh 9.5WSma l bu 2
A!ll 1I O.Wcfl Living Room thtc n
Si Ifl h 9.5W Sm r l:liu 3
s r h 9.5W Sman bu 2

Dimming
Slide the dimming bar left or right to set the
brightness level
16
Note: Screen shown for "dimming only" product.
Please Note: Starsh products cannot be used with an
in-wall dimmer. These products can only be used with
a standard ON/OFF switch. For proper operation, all
dimming must be done through the Starsh devices.

Tunable White
Tap on any part of the wheel or one of the preset
colors to adjust color temperatures from Warm to Cool
Slide the dimming bar left or right to set the
brightness level
17

Color Changing
Tap on any part of the color wheel or one of the preset
colors to select your desired color
Use the slide bars to adjust the brightness and
color saturation
18

Effects
Tap on a preset effect, or create a custom effect by
tapping on the edit button
Some Starsh devices also include a “Music” function.
Tap the music tab to have the color of light change
based on the sounds in the room.
Please note that this functionality utilizes the micro-
phone of the mobile device to determine sounds.
19
20

Tap on the "Schedule" button
21
At device control panel, tap the Timer Button to
create a countdown timer. Select time and conrm
to start the timer.
Select a time for the event to occur
Tap "Repeat" to repeat on certain days of the week,
otherwise the event will only occur once. Select the
days that you would like the schedule to repeat.
Select if you would like the device to turn on or off.
23
22
Schedule
Timer
, ill 'J- f lHiii -=a="'
(
Repeat
Not
Sw it ch
- 15 PM
Save
....
14

Advanced Settings
Additional settings are available in the device
settings menu.
Tap the pen icon in the upper right corner to access
the menu screen
24
<
St msh 9,, sw Sman!bulb3
RQQm:i<itd'len
0 ,.iac tnform Ton
iap~w-Fhm arid Autorna ·
t, -Plr1 Qr, •··
~□
Ale-x
Gat19l
Ania 111
n
Offlln Notlflcelion
O h
C eGroup
FAQ&Feedba

From the "Home" screen, select the (+) button from
the top right corner, and select "Create Group".
25
Enter the group name and click "Save"
28
Select the devices you want to group and then
tap “Conrm”
27
Select the type of devices that you would like to group
26
NOTE: To create groups you will need at least 2 devices.
Create Groups
Ei Create Gro -1> ~
<
~ Oownli.~iihlls
• Outl Ls
C Ci
AIM VCil!Di ca111M ca Id ■ '"'
St rfl!i.h S.5W Srnart bu lb 2
St rfil!ti 9.5W Smart bulb