Sathero SH-400HD User manual

USER'S MANUAL
Digital Satellite Finder
We operate a policy of technically change without prior notice,
the picture of outlook and color is for a reference only, the actual item is the
standard.
SATHERO

FRONT PANEL
USB-Port
MINI USB-Port
HDMI-Port
LNB-IN
LCD-Display
LOCK-LED
POWER-LED
Power-keys
Function -keys
Menu-keys
Exit-keys
LED-keys
Navigation-keys
OK-keys
Connect to U Disk
USB port for PC connection and power supply connection
Connect to TV through HDMI cable
Satellite signal input
Display the TV program, the operation menu and the
detailed parameters
LED lights when satellite signal is locked
Operation:
Red: the finder is on Off: the finder is off
Charging:
Green: The battery is being charged
Switch finder on/off
F1: Switch LCD on/off F2: Mute
F3: To switch between TV program and Radio program
F4: Information
Display the main menu
Leave the current menu, cancel operation
Switch the LED on/off
switch programs ▲, ▼
volume control ◄, ►
OK keys: confirm for selection
8
9
10
11
12
13
1
2
3
4
5
6
7
2
3
6
4
5
7
8
11
12
13
No. Item Description
10
9
1
SATHERO

INSTRUCTION
Charging
If the finder is being used for the first time, it may be necessary to charge
for no longer than 12 hours. If the battery runs low during use, you should
recharge it for 5 or 6 hours, it will be full when the power light turns to
orange from green.
Fully rechargeable Li-on batteries can last approximately 4 hours.
It may be necessary to turn off the finder while charging. A universal
charger operating on 110vac/60Hz or 220vac/50Hz makes it usable
anywhere.
Turn on/off
Press and hold the POWER button for 2 seconds, the finder will turn on.
Press and hold the POWER button for 2 seconds again to turn off.
Language setting
From the system setting menu, you can find the language setting item.
Select your language and press the OK button.
Restore factory setting
From the system setting menu, you can find the factory Reset item.
You can choose “Factory Reset”. Press the OK button to confirm.
After a factory reset, all modified and saved contents will be lost.
Input Local Longitude and Latitude
From the system setting menu, you can find the local position item.
Local Longitude: Input your local longitude.
Local Latitude: Input your local latitude.
SATHERO

INSTRUCTION
Satellite Finding
Select Satellite
From the finding menu, move the cursor to Satellite, you can browse the
satellites list, use [◄][►] buttons to switch between different satellites, select
the one you want, press the OK button.
Select LNB
From the finding menu, move the cursor to LNB Type, Use [◄][►] buttons to
choose LNB Type between Single, Universal and MDU, then move the cursor
to the next bar, Use [◄][►]buttons to select the default LNB frequency. The
LNB frequency must be the same as the LNB on the antenna.
Select parameter
From the finding menu, move the cursor to Frequency, use [◄][►] buttons to
select the parameter that you want.
If no default parameters, press the OK button to edit, you can key in the
frequency, symbol rate and switch the polarization by using direction buttons
and pressing the OK button.
Detect satellite signal
After signal detected, the finder will display signals at the signal bar and
beeps. View the PWR,C/N,MER, a.BER and NIT on the screen, if the value of
POWER is higher, the strength of signal is better and stronger. You can also
search the satellite channel list by pressing the OK button.
From the finding menu, move the cursor to search, Use [◄][►] buttons to
choose search Type between TP, Satellite and Blind.
:
SATHERO

INSTRUCTION
Detect satellite signal
After signal detected, the finder will display signals at the signal bar and
beeps. View the PWR,C/N,MER, a.BER and NIT on the screen, if the value of
POWER is higher, the strength of signal is better and stronger. You can also
search the satellite channel list by pressing the OK button.
From the finding menu, move the cursor to search, Use [◄][►] buttons to
choose search Type between TP, Satellite and Blind.
Value
0.00E： show the longitude of the chosen satellite
DiSEqC：show the DiSEqC port of the chosen satellite
Az：show the azimuth angle of the chosen satellite
El： show the elevation angle of the chosen satellite
Pol：show the polarity angle of the chosen satellite
LAT：show the local latitude of the chosen satellite
LONG：show local longitude of the chosen satellite
NIT：show the longitude of the locked satellite
C/N：show the C/N value of the locked satellite
MER：show the MER value of the locked satellite
a.BER：show the a.BER value of the locked satellite
Software & Parameters upgrade
Copy the software or parameters to the USB stick, insert the USB, the system
will display" USB Device connected", navigate to the USB menu, Press [OK]
to enter the upgrade menu, Use [◄][►] buttons to choose Upgrade Type
between USB Upgrade and Backup Data, move the cursor to Section, Use
[◄][►] buttons to select the mode that you want, to upgrade software select
Software, to upgrade parameters select CSV.
Then move the cursor to File Path, Press [OK] to select upgrade files. Press
Start to upgrade the files. During upgrading, do not power off the finder.
SATHERO

NOTES
Warning
Only qualified personnel may dismantle device and charger.
Do not drop device and charger into water or fire.
Do not shock or vibrate the device and charger.
Make sure that the battery is full charged while upgrading. Do not switch off
the device or pull out the cable while upgrading.
Battery & charger:
Only use original batteries and chargers. The use of any other types may be
dangerous or damage to device.
Dispose of batteries according to local regulations.
Do not crush,puncture the battery. Avoid extreme temperatures and high
pressure.
If left unused, a full charged battery will lose it's charge over time, please
recharge before using.
Unplug the charger from the electrical plug when not in use.
Notice:
Before being ready to seek satellite signal, make sure that the cable is
properly connected first.
While installing the antenna, make sure that the LNB in port of finder is well
connected to the tuner of the antenna with tested cable. Turn the antenna in
the approximate direction, beep when the antenna close to the satellite.
Continue to turn the antenna in the direction that makes the finder beep
quicker. View the PWR value on the screen, continue to turn the antenna until
the finder shows the maximum value of PWR, lock in the best position of
antenna.
Through this function, user can quickly and easily find the right satellite and
accurately set the dish.
SATHERO

LNB Input
F-type connector IEC 169 - 24
Frequency range 950MHz ~ 2150MHz
Input level -65dBm ~ -25dBm Input
Input Impedance 75Ω
LNB power supply 14/18V, Max 650mA
LNB switch control 22kHz
Demodulator
Demodulator front end QPSK, 8PSK, 16APSK,
32APSK
Symbol rate 2Mbps ~ 45Mbps
Measurement Unit dBm, dBuV
Connectors
Serial data interface USB 2.0 Port
Video/audio interface HDMI 1.4
Power supply
Supply voltage DC10.0V 1A
Li-on battery 2600mA
Battery working time about 4 hours
Supply voltage (charger) AC 110 ~ 250V, 50/60Hz
Dimensions
Length x width x height 21 x 12.5 x 3.5 cm
Weight 0.35 Kg
Gross weight 0.65Kg
Temperature
Operating temperature 0°C to + 40°C
Storage temperature -10°C to + 50°C
TECHNICAL SPEC
SATHERO