Satir PK-80 User manual

PK Series
User’s Manual
Trademark Acknowledgments
• SATIR is trademark of SATIR Europe (Ireland). LTD.
• Microsoft, Windows and Windows logo is either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
•Other names and products not mentioned above may be registered trademarks
or trademarks of their respective companies.
Copyright © 2017 SATIR. LTD. All rights reserved.
Handheld Thermal Tablet

0
Table of Contents
ReadThisFirst......................................................................................................................................................1
PartsIntroduction...............................................................................................................................................3
Back and left side........................................................................................3
Right side and top........................................................................................4
GettingReady........................................................................................................................................................4
Quick Start Guide........................................................................................5
Charge the battery.......................................................................................6
Install the battery.........................................................................................7
Turn the power on / off................................................................................9
Local setting ...............................................................................................10
Checking the Information on the LCD....................................................11
Parameter setting......................................................................................12
Pseudo-color selection & Image quality regulation .............................13
Features..................................................................................................................................................................14
Spot analysis tools ....................................................................................14
Area analysis..............................................................................................15
Line analysis...............................................................................................16
Image adjustment......................................................................................17
ISO mode....................................................................................................18
Save image.................................................................................................19
Record video ..............................................................................................20
File browser ................................................................................................21
Data transmission & Update....................................................................22
TroubleShooting.............................................................................................................................................23
Specification........................................................................................................................................................24

1
Read This First
The real Android based tablet thermal camera
PK 80/160 integrates tablet and thermal camera
technologies, which makes the device
multifunctional. Integrating infrared imaging
technology with telecommunications technology.
High quality infrared imaging in combination
with a tablet allows the user to communicate in
real time, and allows live image and video
transmission.
Do not use the device in a wet environment to
avoid liquid/moisture damage.
Before you try to snapshot important subjects,
we highlyrecommend that yousnapshot several
trial images to confirm that the IR camera is
operating and being operated correctly.
Only use chargers, batteries and cables
provided, as others may cause damage to
either/both the battery and device.
Connecting the charger incorrectlymaydamage
the device. Note: Any damage caused by
misuse is not covered by the warranty.
Do not remove the battery before removing the
charger. This may damage the device.
Please Read
Precautions
Introduction

2
Read This First
It is forbidden to disassemble the equipment,
and it is only allowed to be maintained by an
authorized organization.
Before using the camera, please ensure that
you read the safety precautions described.
Always ensure that the IR camera is operated
correctly.
Installing APP without our certification may
result in infrared thermal imaging failure, please
install and use with caution.
Use the following procedures to clean the camera
body, lens, LCD monitor and other parts.
Camera Body
Wipe the bodycleanwithsoftclothor eyeglass lens
wiper.
Lens
Firstuse alens blower toremove dustand dirt,then
removeany remaining dirt by wiping the lens lightly
with soft cloth. Never use synthetic cleaners on the
camera body or lens.
LCD monitor
Use a lens blower brush to remove dust and dirt. If
necessary, gently wipe the LCD monitor with soft
clothor aneyeglass lens wiper to removestubborn
dirt. Never rub or press forcefully on the LCD
monitor. These actions may damage it or lead to
other problems.
Please Read
Equipment
Maintenance

3
PartsIntroduction
Figure
.
Back and left side
1
Visual camera
2
Illuminator
3
Infrared camera
4
Shutter (NUC) button
5
Infrared image save button
6
Battery compartment
1
2
3
4
5
6

4
PartsIntroduction
Figure
Right side and top
1
Volume button
2
Power button
3
Micro USB
4
3.5 mm Headset jack
1
2
3
4

5
Getting Ready
1
Insert the battery to the imager's battery
compartment.
2
Hold the power key down for 3 seconds until the LCD
display is active.
3
Click the infrared App icon .
4
After opening the infrared App, please adjust the
distance between the camera and target. Set
parameters as needed. Analysis tools can be added to
suit your purpose.
5
After adding the analysis tools, we suggest you freeze
the image, and also you can click the Image icon to
save the image .You can click the File icon to find the
image you saved.
6
If you want to save a video, you can click the Video
icon. Then click the File icon to find the video.
7
Use the standard USB cable, you can copy your file to
the computer.
8
To power off the camera, hold the power key for 3
seconds until the device turns off. After that please
remove the battery out.
Quick Start Guide
Procedure

6
Getting Ready
General Before using the device for the first time or when the
battery has been unused for extended periods, you
must charge the battery fully.
Procedure
Charge the battery
1
Plug the small end of the charger into the
USB port of the device.
2
Plug the large end of the charger into an
electric socket.
3
When fully charged, disconnect the device
from the charger.
First unplug the charger from the device.
Then unplug it from the electric socket.

7
Getting Ready
General Chargethe batterypack fully before using it for the first time.
Procedure Follow this procedure to install/take out the battery pack.
Note Please replace the battery in 30 seconds, otherwise
Install the battery
1
Insert the battery pack into the slot and close the
back cover, and then push the locker to the right
to lock the cover.
1
Pull out the battery pack:
Push the locker to the left to unlock the cover, and
lift up the cover, then pull out the battery.

8
will result in the loss of the saved parameters.
Remove the battery pack when the camera is not in use.

9
Getting Ready
General The touch screen is lit while the power of the camera is on.
Procedure
Note
Turn the power on / off
1
Press and hold the power switch for 3 seconds.
•The screen will be power on.
2
A startup image will appear on the screen.
Click the infrared App icon to access the
infrared camera function.
3
Press power switch and then there will pop up a
prompt box and click the [Power off].
You can download the IR Wizard APP installation
package from our website www.satir-eu.com or find out
the package in the built-in storage directory /file1/file2,
then install the APP for editing thermal image and
creating temperature measurement report.

10
Getting Ready
General You need to set the local language and time when the IR
camera is turned on for the first time.
Procedure Follow this procedure to set your local language.
1
Find out and click Settings icon .
2
Slide up tofindout Language & input / Date & time
option.
3
Click to set the local language and time.
Local setting

11
Getting Ready
General The following displays in information view.
Main interface
Explanation This table explains the figure above.
Checking the Information on the LCD
1
Battery status
2
Main page
3
Main tool
4
Toolbar
5
Auto Shutter Time & Device Info
6
Temperature scale
7
Shortcuts
8
File browser
1
2
4
3
6
5
7
8

12
Basic Settings
Parameter Setting
General Click the icon , the menu will pop up as below.
Figure
Explanation This table explains the figure above.
Procedure Modify the parameters according to work field.
Parameter setting
1
Parameters Set up
2
Pseudo-color Select
3
Image quality regulation
1
Click the main page .
2
Click parameter setting icon .
3
Click one option of the list, then slide to set
the value.
4
Click Confirm to save the changes, if you do
not want to save the changes, click Cancel.
5
Click to return and hide the menu.
1
2
3

13
Basic Settings
Pseudo-color Select
General You can select IRON, IRON INV, RAINBOW,FEATHER
GRAY or GRAY INV according to the work field.
Procedure Follow this procedure to select the pseudo-color.
1
Click the main page .
2
Click pseudo-color setting icon .
3
Click the pseudo-color you want to select.
4
Click to return and hide the menu.
Image quality regulation
General Select Original Image, Image Smooth or Detail Enhance.
Procedure Follow this procedure to adjust the quality of image.
1
Click the main page .
2
Click icon .
3
Click the image mode you want to select.
4
Click to return and hide the menu.
Pseudo-color selection & Image quality regulation

14
Features
Spot analysis tools
General This topic briefly explains how to set the analysis tools on
the thermal image.
Procedure Follow this procedure to set Spot analysis.
Spot Analysis tools
1
Click the Analysis button .
2
Click the icon to add a spot.
3
Warning Mode Settings
Press and hold the spot you want to set for a
while, then the warning mode interface will
pop-up.
In this mode, you can set the warning
temperature and warning mode.
After you finish the settings, click the Confirm
to save you settings.
4
Moving the spot
Press and drag the spot directly to anywhere of
the image.
5
Removing the spot
Move the spot to the icon to remove the
spot.

15
Features
Area analysis
Procedure Follow this procedure to fulfill Area analysis.
Area analysis
1
Click the Analysis button .
2
Click the or icon to add a
rectangle or oval analysis.
3
Setting the analysis area
Press and hold the area you want to set for a
while, then the area display settings will pop-
up.
After you finish the settings, click the Confirm
to save your settings.
4
Moving the area
Drag the line analysis directly to anywhere of
the image.
5
Removing the area
Move the rectangle or oval to the or
icon to remove the rectangle or oval.
6
Changing the shape of the analysis area
Hold and drag the corner or edge of the area to
change the shape of the analysis area.

16
Features
Line analysis
Procedure Follow this procedure to fulfill line analysis tool.
Line analysis
1
Click the Analysis button .
2
Click the line icon to add a line analysis.
3
Moving the line
Drag the line analysis directly to anywhere of
the image.
4
Removing the line
Drag the line to icon to clear it.

17
Features
Image adjustment
General You can adjust the Level (brightness) and Span (contrast)
of the image captured by IR camera, manually or
automatically. The default setting is automatic adjustment.
Procedure Follow this procedure to adjust the L/S manually.
About Image
1
Click the Image button .
2
Click the L/S icon to open Level/Span
setting menu.
3
The L/S mode selection interface will pop up.
When you choose the manual regulation mode,
click the number you want to change to call the
Level or Span adjustment menu. Then you can
slide to select the value or click the number and
input the value directly. After you finish the
settings, click “Confirm” to save your settings.
You can also slide on the screen directly as the
screen prompt to adjust Level & Span.
Slide up or down to adjust the level.
Slide left or right to adjust the span.
4
You can click Settings which on the top right
corner to set the auto shutter time or click
and left side button of the device for shutter.

18
Features
ISO mode
Procedure Follow this procedure to set the ISO mode.
About image
1
Click the Image button .
2
Click the ISO icon .
3
Select Between/Above/Below ISO mode.
4
Click ISO Color Picker.
Pick up one color from the ring color plate and
then click the center of the ring color plate to
confirm.
5
Click Confirm to save the settings.
Click Cancel to cancel the settings.