Satson HDMI-SPL-2008H User manual

HDMI-SPL-2008H
1x8 HDMI 1.3 Distribution Amplifier
User Manual
Made in Taiwan

~ 1 ~
Safety and Notice
The HDMI-SPL-2008H 1x8 HDMI 1.3 Distribution Amplifier has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like all electronic
equipments, the HDMI-SPL-2008H should be used with care. Please read and follow the safety instructions
to protect yourself from possible injury and to minimize the risk of damage to the unit.
zFollow all instructions and warnings marked on this unit.
zDo not attempt to service this unit yourself, except where explained in this manual.
zProvide proper ventilation and air circulation and do not use near water.
zKeep objects that might damage the device and assure that the placement of this unit is on a stable
surface.
zUse only the power adapter and power cords and connection cables designed for this unit.
zDo not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.

~ 2 ~
The HDMI-SPL-2008H 1x8 HDMI 1.3 Distribution Amplifier provides the most cost effective and
advanced HDMI 1.3 splitter solution on the market, by which the high definition video and high quality audio
can be transmitted to 8 different locations without losing quality. With built-in USB firmware update
mechanism, the compatibility among countless HDMI sources and receivers can be further guaranteed.
With 12 bit deep color video and high definition audio support, HDMI-SPL-2008H is suitable for high quality
A/V broadcasting, digital signage and education applications!
Features
zHDMI 1.3c and DVI 1.0 compliant
zHDCP 1.2 compliant
zWide Frequency Range: 25MHz~225MHz
zVideo bandwidth: 6.75GBPS
zSupports conversion of HDMI signaling to DVI
zResolution up to 1080p or WUXGA
zAutomatic EDID learning
zSupports xvYCC
zUSB firmware update for expanding compatibility
zSupports Dolby Digital, DTS-HD and Dolby True HD audio
zEasy installation
Automatic EDID learning will detect all the connected HDMI equipped monitors and analyze all the
content of EDID. The EDID with minimal resolution support will be the reference EDID for incoming
HDMI source players.
I
ntroduction

~ 3 ~
Specifications & Package Contents
Model Name HDMI-SPL-2008H
Technical
HDMI compliance HDMI 1.3c [Deep Color, xvYCC color space supported]
DVI compliance DVI 1.1
HDCP compliance Yes
Video bandwidth Single-link 225MHz [6.75Gbps]
Video support Up to WUXGA [1920x1200@60Hz] & UXGA [1600x1200@60Hz]
Audio support DTS-HD Master Audio, Dolby TrueHD
Dolby Digital, DTS, DVD-Audio, LPCM, SACD, MPCM
ESD protection [1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset — ±2kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
USB firmware
updatable YES
CEC Channel No
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
Input 1x HDMI [7.1ch audio & video]
Output 8x HDMI [7.1ch audio & video]
HDMI connector Type A [19-pin female]
Mechanical HDMI-SPL-2008H
Housing Metal enclosure
Dimensions
(L x W x H)
Model 340 x 95 x 45mm
Package 510 x 230 x 70mm
Carton 510 x 410 x 252mm
Weight Model 910g
Package 1.7g
Fixedness Wall-mounting case with screws
Power supply Interlocking 5V 2A DC
Power consumption 4 Watts [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents
1x HDMI-SPL-2008H
2x 1RU rack-mounting ear
1x 5V power adapter
1x User Manual

~ 4 ~
Input Panel
1. HDMI OUT1-OUT8: Eight distributed HDMI outputs to HDMI displays
2. HDMI IN: Connect to a HDMI input source
3. USB: For technical support only [firmware update]
4. Power: Lights on when power is on
5. +5V DC: Connect to the +5VDC 4A power supply unit
When the connected HDMI equipped monitor is verified as HDMI and HDCP compliant, the
corresponding green LED will blink.
Panel Descriptions
Hardware Installation
1 23
451

~ 5 ~
Broadcasts HDMI signal to 8 HDMI displays!
1. Switch off all devices, including monitors.
2. Connect to the receivers.
3. Connect an HDMI source (such as a Blu-ray Disc player) to the HDMI In.
4. Plug in 5V DC power supply.
5. Power on the HDMI monitors.
6. Power on the HDMI source.
HDMI source
HDMI-SPL-2008H
HDMI cable
HDTV
HDMI cable HDMI cable
HDMI cable
HDMI cable
HDTV HDTVHDTV HDTV HDTV HDTV HDTV

~ 6 ~
1. While connecting a new monitor to the splitter, experiencing a short period of time no display may be
expected. Automatic EDID learning will analyze the newly connected monitor to see if the EDID for the
HDMI input is necessary to update!
2. For long range high definition HDMI transmission applications, please adopt CAT-5 cable based HDMI
extenders.
3. For firmware update through USB, users MUST first turn off the power, plug USB cable connected to
your PC, and then power up the module! In this setup, the power LED indicator will NOT blink, and this
is normal! Execute the attached or download EPFlash.exe, and the following window will pop up. Click
on “OpenFile” button to direct to the new firmware HEX file, and keep PORT at USB 0! Meantime, keep
“Program With Verification” selected, and then click on “START” button on the bottom of the window!
Wait for seconds until the update process is completed! After firmware update is successfully
accomplished, please unplug USB cable and power off the splitter!
Notice

~ 7 ~