Schlage Link LE120 User manual
Max. 600W
Incandescent
1
2
3
-
+
-
+
Press
Hold
within1.8m
Press
Introduction
The Appliance Module (model LE120) works with the Schlage
LiNK system as both a lamp or small appliance controller and a signal
repeater to help extend the range of the Schlage Bridge.
Appliance Module
Model LE120
User Guide
Enrollment
1. Disconnect the bridge from power and Ethernet.
2. Install a 9-volt battery into the bridge (supplied).
3. Hold the bridge within 1.8 metres of the appliance module
throught all of the next steps.
4. Press and release the plus (+) button on the bridge.
5. Press the button on the appliance module.
6. Observe the lights on the bridge. The orange light will blink rapidly
while enrollment is taking place. Enrollment is complete when
the orange light becomes solid.
7. Uninstall battery from bridge.
8. Reconnect power and Ethernet to the bridge.
Installation
1. Plug the appliance module into any available outlet.
•The appliance module can be used to control a lamp or small
appliance.
•The appliance module repeats the Z-Wave™ signal. In some homes,
the appliance module must be used to improve communication
between the bridge and the lock. During the online portion of the
setup, the system will determine if it is communicating properly or not.
You can move the appliance module during online setup if necessary.
•The appliance module should be installed into any indoor, three-
prong, 220-240 volt A/C outlet.
2. (Optional) Plug a lamp (incandescent or CFL) or small appliance
into the front of the Z-Wave™ appliance module.
Press
Remote Operation
1. To control the lamp or appliance remotely from your PC
Log into your account at;
Australia: schlagelink.com.au
New Zealand: schlagelink.co.nz
Log in to the application, select the appropriate house tab.
To control the lamp or appliance remotely from your
mobile phone;
Download the phone application from;
Australia: link.schlage.com.au
New Zealand: link.schlage.co.nz
Open application. Click the lighting and automation tab.
The appliance module will be displayed.
2.
Manual Operation
•Press the button once to turn the lamp/appliance on or o.
WARNING
FOR INDOOR USE ONLY!
The device plugged into the Z-Wave™ controlled outlet on this module must
not exceed 2200 watts (50hz, 10A).
To reduce the risk of electric shock, this product has a grounding type
plug that has a third (grounding) pin.This plug will only t into a grounding
type power outlet. If the plug does not t into the outlet, contact a qualied
electrician to install the proper outlet. Do not change the plug in any way.
Any modication or use other than described may damage the unit and will void the warranty.
It could also result in:
RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS
Controlling Appliances:
Exercise caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a dierent room than the controlled
appliance, also an unintentional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be
powered on due to timed event programming. Depending upon the appliance, these unattended or unintentional operations could possibly
result in a hazardous condition. For these reasons, we recommend the following:
•DO NOT use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended
or unintentional or automatic power on control.
NOT FOR USE WITH
MEDICAL OR LIFE
SUPPORT EQUIPMENT
Z-Wave enabled devices
should never be used to
supply power to or control the
On/O status of medical or life
support equipment.
Specications
Power 220 - 240 VAC, 50Hz
Signal (Frequency) 921.42MHz
Maximum load for both outlets 10 Amps
Range: Up to 33 metres line of sight between the Wireless
Controller and the closest Z-Wave receiver module.
Operating Temperature Range: 0-55° C
For indoor use only.
Specications subject to change without notice due to
continuing product improvement
Customer Service: 1800 LiNK HELP ( Australia 1800 5465 4357)
0800 LiNK HELP (New Zealand 0800 5465 4357)
Warranty information is available at www.ingersollrand.com.au and www.ingersollrand.co.nz
All brand names shown are trademarks of their respective owners.
Table of contents
