SCORPION Sky Strider 280 User manual

Scorpion Sky Strider 280 Assembly Manual
 "
1

Thank you for purchasing Scorpion Sky Strider 280
FPV racing frame.
Please, prepare the following tools and materials before
assembly.

3mm phillips 1.5mm hex 2mm hex Thread locker
Parts
UPPER FRAME ＊2 ALUMINIUM CROSS MEMBER ＊2
LOWER DECK ＊1 UPPER DECK＊1
FRONT FRAME MOUNT ＊1 TRANSMITTER BOARD ＊1
FIXING PLATE BRACKET ＊4 LENS FIXING BOARD ＊1
LENS UPPER BOARD ＊1 LENS LOWER BOARD ＊1
DECK CROSS MEMBER ＊6 SIDE STRAIGHTENER ＊4
FRONT/REAR STRAIGHTENER ＊2 UNDERCARRIAGE＊4
MOTOR ARM ＊4 LANDING GEAR *4 SUSPENSION BALL ＊4
UPPER ANGLED ARM CLAMP ＊4 MOTOR GUARD ＊4
LOWER ANGLED ARM CLAMP ＊4 ANTENNA TUBE ＊2
Screws
M3 *4 set screw x4
M2 * 4 round Phillips’ x 8
M2.5 *6 hexagonal round
head x26
M2.5 *6 hexagon head x2
M2.5 *12 hexagon head x4
M2.5 *14 hexagon head x8
M3 *6 flat head x2
x4
2

There are two carbon fibre
decks (upper and lower
deck) inside the box. The
upper deck is the one pre-
assembled with nuts.
Assemble the deck crossing member on the lower deck board
with M2.5 *6 round screw at the appropriate position.
As shown below:
3

Insert the side
straightener on
both sideways and
insert the front
straightener at the
front and rear
straightener at the
rear.
Position the upper deck properly
and tighten with M2.5 hexagon
round screw. After placing the
upper plate, tighten screws across
other parts.
Leave the two front screw slots empty
after which you mount the aluminium
alloy parts.
4

This section shows how to assemble the angled arm clamp.
The picture below shows the two modules of the angled arm
clamp, which are upper and lower.
Position the upper and lower
modules in between the decks
using M2.5 *14 hexagon head to
go through the frame and the
clamp but do not tighten at this
stage.
Slot in the 3mm carbon
motor arm into the clamp (front
motor arm).
Use M2.5 *12 hexagon
screw fix through the
motor arm and tighten
the screws along with
the additional two M2.5
*14 screws.
5

When installing the rear arm, please note that the direction of
the holes near the frame is for undercarriage.
The two holes should be parallel with the frame.
!!
The direction of the holes should
be as shown in the picture.
6

This section shows how to
assemble the camera
damping system. Insert the
damper in between the lens
upper and lower board.
Use M2 *4 Phillips’ head to fix
the camera mounted on the L
type arm.
Then attach the other side to
the damping plate(lens upper
board) with the aid of M3 *6 flat
head screws.
Put on the
fixing plate bracket. Please,
take note of the direction of the
thread side.
With above
instruction
in place, you
are done
with the
dampener.
7

To assemble the upper frame,
use M2.5 *6 hexagon round
heads to cross between
member frames. The member
frame with holes is for the
antenna tube and should be
placed at the rear.
Use M2 * 4 round Phillips’ screw,
fixed to the frame, to mount
between two frames.
Slot the upper frame into the
rear channel on the upper
deck.
Use M2.5 *6
hexagon
round screw
to tighten the
frame
mounted on
the deck.
8

To assemble the camera damping system on the upper frame.
Use M2.5 *6 round hexagon screw
in the front but do not tighten.
Then, use the M2.5 *6 hexagon
screw with cup washer screw in
the adjustable track, now you can
tighten the front screw when it is
in the position as required.
Mount the transmitter board
between both sides of the upper
frame.
Use M3 *6 set screw to lock the
landing gear on the undercarriage.
9

Use M2.5 *6 to
assemble the
undercarriage under
the motor arm.
Then, heat up the
antenna tube a little
bit and bend it, after
which you insert it
into the rear cross
member.
10