dji MAVIC 2 PRO User manual

Mavic 2 Pro Quick Start Guide
V1.0 2018.07
Aircraft (L1P)
The DJITM MAVICTM 2 Pro features Omnidirectional Obstacle Sensing, an Infrared Sensing System*,
and a fully stabilized 3-axis gimbal with a 1” CMOS sensor camera that shoots 4K video and 20-
megapixel photos. DJI signature technologies such as Obstacle Avoidance and Intelligent Flight
Modes like HyperLapse, ActiveTrackTM 2.0, QuickShot, Panorama, and Advanced Pilot Assistance
Systems, help you capture complex shots effortlessly. The Mavic 2 Pro boasts a maximum flight
speed of 44.7 mph (72 kph) and a maximum flight time** of 31 minutes.
1. Gimbal and Camera
2. Forward Vision System
3. Downward Vision System
4. Lateral Vision System
5. Downward Infrared Sensing System
6. Fill Light
7. microSD Card Slot
8. Front LEDs
9. Motors
10. Propellers
11. Antennas
12. Aircraft Status Indicator

13. Upward Infrared Sensing System
14. Backward Vision System
15. Intelligent Flight Battery
16. Battery Level LEDs
17. Power Button
18. Battery Buckles
19. USB-C Port
20. Link Button/Linking Status Indicator
* The Vision Systems and Infrared Sensing Systems are affected by surrounding conditions. Read
the Disclaimer and Safety Guidelines and watch the tutorial in the DJI GOTM 4 app or on the official
DJI website to learn more. http://www.dji.com/mavic-2
** Maximum flight time was tested in an environment with no wind while flying at a consistent
15.5 mph (25 kph). This value is for reference only.
Remote Controller (RC1A)
Built into the remote controller is the DJI’s long-range transmission technology OCUSYNCTM 2.0,
offering a maximum transmission range of 5 mi (8 km) and displaying video from the aircraft to the
DJI GO 4 app on your mobile device at up to 1080p. An on-board LCD screen gives real-time aircraft
data information and the detachable control sticks make the remote controller easier to store.
Maximum run time: 2 hours and 15 minutes*

1. LCD Screen
2. Flight Pause Button
3. 5D Button
4. Control Sticks
5. Removable Power Button
6. Antennas
7. RTH Button
8. Control Sticks Storage Slot
9. Reserve Video-Downlink Port (USB)
10. Mobile Device Clamp
11. Flight Mode Switch
12. Gimbal Dial
13. Aperture/Shutter Adjustment Dial
14. Record Button
15. Focus/Shutter Button
16. Video-Downlink/Power Port (microUSB)
17. C1 Button (Customizable)
18. C2 Button (Customizable)
* The remote controller is able to reach its maximum transmission distance (FCC) in a wide-open
area with no electromagnetic Interference at an altitude of about 400 ft (120 m).
The maximum runtime is tested in a laboratory environment. This value is for reference only.
Specifications
Aircraft
Weight
907 g
Max Speed
44.7 mph (72 kph) in Sport mode without wind
Max Service Ceiling Above
Sea Level
19685 ft (6000 m)
Max Flight Time
31 minutes (0 wind while flying at a consistent 15.5 mph (25 kph))
Operating Temperature
14° to 104°F (-10° to 40°C)
GNSS
GPS + GLONASS

Operating Frequency
2.4-2.4835 GHz; 5.725-5.850 GHz
Gimbal
Controllable Range
Pitch: -90° to +30°
Yaw: -90° to +90°
Camera
Sensor
1’’ CMOS; Effective pixels: 20M
Lens
FOV: approx. 77°
35mm format equivalent: 28 mm
Aperture: f/2.8-f/11
Focus: 1 m to ∞
ISO Range
Video: 100-6400
Photo: 100-3200 (auto); 100-12800 (manual)
Electronic Shutter Speed
8-1/8000 s
Max Image Size
5472×3648
Still Photography Modes
Single shot
Burst shooting: 3/5 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7 EV
Bias
Interval
Video Recording Modes
4K: 3840×2160 24/25/30p
2.7K: 2688×1512 24/25/30/48/50/60p
FHD: 1920×1080 24/25/30/48/50/60/120p
Video Storage Bitrate
100 Mbps
Photo
JPEG, DNG (RAW)
Video
MP4, MOV (MPEG-4 AVC/H.264, HEVC)
Supported SD Cards
microSD™
Max Capacity: 128 GB (UHS-1 Speed Grade 3 rating required)
Remote Controller
Operating Frequency
2.4-2.4835 GHz; 5.725-5.850 GHz
Max Transmission Distance
(Unobstructed and free of
interference)
FCC: 8 km; CE: 5 km; SRRC: 5 km
Operating Temperature
32° to 104° F (0° to 40° C)
Battery
3950 mAh

Operating Voltage
1800mA @ 3.7 V (when charging the mobile device)
Supported Mobile Device
Size
Thickness supported: 6.5 - 8.5 mm, Max length: 160 mm
Supported USB port types: Lightning, Micro USB (Type-B)
USB-C
Charger
Voltage
17.6±0.1 V
Rated Power
60 W
Intelligent Flight Battery
Capacity
3850 mAh
Voltage
17.6 V (max)
15.4 V (typical)
Battery Type
LiPo
Energy
59.29 Wh
Net Weight
Approx. 297 g
Charging Temperature
Range
41° to 104°F (5° to 40°C)
Max Charging Power
80 W
For more information, read the User Manual:
http://www.dji.com/mavic-2
※ This content is subject to change without prior notice.
Download the DJI GO 4 App and Watching Tutorial Videos
Search “DJI GO 4” in the App Store or Google Play or scan the QR code below to download the app
on your mobile device.
Watch the tutorial videos at www.dji.com/mavic-2 or in DJI GO 4 by tapping the icon in the top
right corner of your screen.
DJI GO 4 is compatible with iOS 9.0 (or later) or Android 4.4 (or later).

Preparing the Aircraft
1. Remove the gimbal cover from the camera.
2. Match the propellers to motors.
Marked Unmarked
3. Press the propellers down firmly and rotate in the lock direction.
4. Unfold the front arms and the propellers.
5. Unfold the rear arms and the propellers.
6. Unfolded
Unfold the front arms and the propellers before the rear ones. All arms and propellers
must be unfolded before takeoff.

Charging the Batteries
Use the provided charger to fully charge the Intelligent Flight Battery before first use.
Remove the Intelligent Flight Battery
Charging Time:
~1 hour 30 minutes
Charging Time:
~2 hour 15 minutes
Remove the remote controller cable before charging.

Checking the Battery Levels and Powering On/Off
Press once to check the battery level.
Press, then press and hold to turn on/off.
Press once to check the battery level on the LCD screen.
Press once, then press and hold to turn on/off the remote controller.
Preparing the Remote Controller
1. Unfold the antennas and mobile device clamps, then attach the control sticks.

2. Place one end of the RC cable to the end of the slot.
3. Attach your mobile device within the clamps.
Ensure the control sticks are firmly mounted.
The remote controller cable with the Lightning connector is mounted by default.
Use the appropriate cable for your mobile device to connect to the remote
controller. When using an iPad or tablet, use the USB port on the remote
controller.
Do not use the Micro USB and the USB ports simultaneously for linking video.
Preparing for Takeoff
1. Power on the remote controller
2. Power on the aircraft

3. Launch DJI GO 4
Flight
Before taking off, make sure the Aircraft Status Bar in DJI GO 4 displays “Ready to Go.”