Attop W80 User manual

W80 Instructions For Use
(Please keep and read this manual carefully before using this product.)
4
Customer Service Email: [email protected]
www.attoptoys.com
Get 24/7 assistance at
Use camera or QR scanner to scan
Or Visit: https://attop.afterservice.vip

-01-
1. Please read this Disclaimer & Warning and Safety Guidelines carefully
before using our product. This product is not recommended for people
under the age of 14. By using this product, you hereby agree to this
disclaimer and signify that you have read it fully. You agree that you are
responsible for your own conduct and any damage caused while using this
product, and its consequences. You agree to use this product only for
purposes that are proper and in accordance with local regulations, terms
and all applicable policies and guidelines ATTOP may make available.
2. When using this product, please be sure to strictly abide by the specifica-
tion requirements and safety guidelines stated in this document. Any
personal injury property damage, legal disputes and all other adverse
events caused by the violation of the safety instructions or due to any other
factor, WILL NOT be ATTOP’s responsibility.
DISCLAIMER & WARNING
SAFETY GUIDELINES
Check Before Using:
① This product is a high precision drone that integrates various electronic
stability and control mechanisms. Please be sure to set up this drone careful-
ly and correctly to ensure safe, accident-free operation.
② Please be sure that the batteries of the drone and controller are clean,
undamaged and, fully charged.
③ Please be sure that all the propellers are undamaged and are installed in
the correct orientation.

-02-
④Please do a thorough check of the product before each use. Inspect the
integrity of the parts, any signs of cracks and wear of the propeller, battery
power and effectiveness of the indicator, etc. After doing a complete check,
if any issue is found, please stop using the product until the issue has been
solved.
Flight Environment:
Fly in Open Areas Maintain Line
of Sight
Fly Below
390 feet (120 m)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Avoid flying over or near obstacles, crowds, high voltage power lines, trees,
South Pole and North Pole, base station.
DO NOT fly near strong electromagnetic sources such as power lines and
base stations as it may affect the onboard compass.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Don’t use this drone in adverse weather conditions such as rain, snow, fog,
and wind.

-03-
Operation Requirements：
①Please don’t use this product to follow any moving vehicles.
②During the flight, only turn off the motor in case of an emergency.
③As battery becomes low return the drone back to your starting point.
④This product should not be used while drinking alcohol, if you are feeling
fatigued, taking medicine, or feeling any physical discomfort.
⑤Beware of the noise volume the drone produces. Keep your distance to
avoid ear damage.
Use of Battery:
Use of Gimbal:
①Please ensure batteries are fitted in the correct orientation as shown in
the instruction manual.
②Avoid short circuits by fitting the batteries incorrectly, and do not crush
or squeeze the batteries as this could carry the risk of an explosion.
③Do not mix new and old batteries as this can lead to a poor performance
of the product.
①The Gimbal is detecting rough 10 seconds after compass calibration.
When the Gimbal indicator light is solid on, it indicates that the detection
completes.
②Do not touch the Gimbal.
③If the Gimbal getting stuck 5 times or more, it will be out of running and
the Gimbal indicator light will be solid on. Please reboot the drone.
⑥Stay away from the
rotating propellers and
motors.
⑦Don’t fly in the
No-Fly Zone.
⑧Don’t touch the
Gimbal.

-04-
④Dispose of used batteries carefully. Do not litter.
⑤Please keep dead batteries away from heat and fire.
⑥If the device is not going to be used for an extended period of time,
remove batteries to prevent potential damage from battery leakage.
⑦It is recommended to only use the USB charging cable that comes with
the drone to charge the battery.
⑧Don't connect the battery directly to wall outlets or carcigarette lighter
sockets.
⑨Don't attempt to disassemble or modify the battery in any way.
⑩Don't use the battery if it gives off an odor, generates heat, becomes
discolored, deformed, or appears abnormal in any way. If the battery is in
use or being charged, remove it from the device or charger immediately
and discontinue use.
Don't pierce the battery casing with a nail or other sharp object, break it
open with a hammer, or step on it!
Always charge the batteries in a fireproof container and away from
combustible materials. Don't charge the batteries on surfaces that can
catch fire. This includes: wood, cloth, carpet, or in the application's device.
Don't immerse the battery in water or allow it to get wet.
Don’t solder battery terminal directly.
Keep the battery out of the reach of children or pets.
Don't short-circuit the battery by connecting wires or other metal objects
to the positive(+) and negative(-) terminals.
11
12
13
14
15
16
Li-Po Battery Disposal & Recycling
Waste Lithium-polymer batteries must not be placed with household trash.
Please contact local environmental or waste agency or the waste agency
or the supplier of your model or your nearest Li-Po battery recycling center.

-05-
×1 ×1 ×2
×8 ×1 ×1
MAINTENANCE
①Clean the product after each use with a clean, soft cloth.
②Avoid prolonged exposure to direct sunlight and avoid buildup of heat
on the drone.
③ This device is not waterproof and must not be submerged in water
under any circumstance. Failure to maintain the device completely dry will
result in the failure of the unit.
④Check the charging plug and other accessories for signs of damage
frequently. If any part of the device is damaged, refrain from flying until
maintenance can be carried out.
Drone Controller Drone Battery
Propeller USB Charging Cable
with Charge Hub Screwdriver
PACKAGE CONTENTS

-06-
DRONE’S DETAILS
TOP
BOTTOM
Lights
Battery
Propeller B
Propeller B
Propeller A
Propeller A
HD Camera
(Gimbal)
Power Switch

-07-
TOP
BACK
FRONT
CONTROLLER DETAILS
Controller Functions
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Left Joystick
Gyroscoper
Calibration
LED Screen
Right Joystick
Unlock Take off
Landing
Return to Home
Handgrip
Antenna
Phone Holder
Take Photo
Camera Angle
Adjustment
Low/Fast Speed
Record Video
Charge
Power Switch
OFF ON

-08-
•Left/Right Throttle Swift
To switch it to the right throttle, turn off the controller, then, long press
the ‘ ’ button and turn on the controller at the same time. ‘MODE 2’
showing on the LED screen means it switched successfully.
If need to change back to left throttle, just reboot the controller.
Screen
2. Flight signal 3. Compass calibration 4. Return to home1. Gyroscope calibration
5. Drone battery energy 7. Controller battery
energy
8. Height
6. Take photo/
video
9. Distance 10. GPS status 12. Low/Fast
speed
13. Throttle switch (Mode 1 left throttle/Mode 2 right throttle)
11. GPS signal
1234
567
8
9
10
11
12
13
The controller defaults the left throttle.

-09-
•Return to Home
Press the button to start the RTH. The controller emits a “beep-beep”
sound every 1.5 seconds as the drone flies back to the recorded Home
Point.
Press the RTH button again to exit RTH procedure and regain control of
the drone.
•Photo/Video
•Speed Switch
Push the gear “ ” to right on the Controller and you will hear a
“beep ”, indicating the drone is at low speed.
Push the gear “ ” to left and you will hear two beeps, indicating
the drone is at high speed.
Low speed is the default setting.
•GPS Mode Switch
•Unlock/Lock
Press the camera button on the Controller, the camera takes one
photo.
Press the same video button on the Controller, the camera will take
the video. Press again to exit shooting.
When turning on the controller, the default mode is the GPS Mode. Check
the icon on the controller screen to confirm GPS status.
Press the button ” “ then the motor will rotate.
Press the red button “ ” again, the motor will stop rotating and the
drone will be locked.

-10-
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Controller Operation
Left throttle
Ascend
Descend
Rotate Left Rotate Right
Up
Left Right
Down
Left Joystick
Forward
Backward
Up
Down
Left Right
Right Joystick
Fly to
Left
Fly to
Right

Right throttle
-11-
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Controller Operation
Ascend
Descend
Rotate Left Rotate Right
Up
Left Right
Down
Left Joystick
Forward
Backward
Up
Down
Left Right
Right Joystick
Fly to
Left
Fly to
Right

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
-12-
INSTALLATION
Installation: Push the battery into the battery compartment of the drone.
Make sure it “clicks” into place indicating the battery is firmly installed.
Attention:
The battery should be installed firmly. Failure to do so may affect the flight
safety of your drone. The drone may crash due to a power-cut during
flight.
Removal: As shown above, press and hold the locks on both sides of the
battery at the same time to remove the battery.
Drone Battery

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
-13-
1. Connect the USB cable to a USB socket such as a mobile power supply.
2. Connect the controller with the USB cable and controller handle emits a
"beep" sound. Flashing controller battery energy icon indicates charging
status. Charging is completed when the icon is solid.
Low battery warning
When the controller battery energy icon is flashing and controller
handle emits a "beep" alarm sound every 3 seconds, indicating that the
controller power is too low. The controller needs to be charged at this time.
Notes:
1. Charge only by USB cable of factory provided (Type C).
2. Use a power supply with standard output voltage 5V and current greater
than or equal to 2A, otherwise there is a risk of overloading the USB cable
and battery. A full charge takes approximately 90 mintutes.
Installing TF Card
Controller Battery
Charging Cable for Controller
Tips: Please turn off the controller before charging.
As shown in the above figure, please insert the TF card (needs to be
purchased separately) into the TF card slot. A “click” signifies it is inserted
correctly. It will indicate memory card capacity in “SD Card testing ” of
APP interface, that means the card was indentified.
1. Click the SD card testing will delete all contents in the SD card and connot
be recovered. Please be careful before confirmation.
2. The original pixel-sized pictures and videos will be stored on the TF card.
TF
USB Adapter
(5V/2.0A)
SD

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
AB
B A
-14-
Propellers
The drone will not fly unless the correct propeller is installed on the correct
motor shaft. See illustration above. An “A” or “B” is printed on the back of
each propeller. Lock the propeller to the motor shafts with screws rotating
each screw clockwise.
Installation
HEAD
Removal
For propeller removal, use the screwdriver (provided) to rotate counter-clock-
wise and remove propellers.

-15-
Phone Holder
①Separate the Mobile Device Holder by pulling out from of
controller.
②Adjust the Mobile Device Holder for a tight grasp of your phone.
2 1
1
2

-16-
CHARGING
①Connect the USB cable to a USB socket such as a mobile power supply
(Use a power supply with standard output voltage 5V and current
greater than or equal to 2A, otherwise there is a risk of overload-
ing the USB cable and battery). Connect the charger with the USB
cable, and then connect the battery with the charger. The charger's LEDs
begin flashing. When all four LEDs become solid, full charging is complet-
ed.
②The charging time of a single battery is 4~6 hours.
1. Charge only by USB cable of factory provided (Type C).
2. Before charging, please carefully review the “Use of Battery” section
contained in “SAFETY GUIDELINES”.
USB Adapter
(5V/2.0A)
Charging Cable for Drone Battery

-17-
Downloading App
OPERATION GUIDE
Scan the QR code, corresponding to either App Store™ or Google
™ Play Store and download the “ Attop View ” application for free.
Required Operating Systems: iOS v8.0 and later / Android v4.3 and later
Tip: Please use a smartphone that can support receiving 2.4G and
5G WiFi signals.
HEAD
To unfold the drone by following the steps below.
Step 1: Unfold the front arms.
Step 2: Unfold the rear arms and place the drone on a flat, level surface.
Head should face forward.
Unfolding the Drone
CONTACT US
Please do not hesitate to contact us if you need further support.
Customer Service Email:
[email protected]

-18-
Connecting to Wi-Fi
1. If pairing fails, please restart the drone, press and hold the
button and then turn on the power of controller.
2. Please operate pairing between drone and controller before
connecting WiFi signal.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
① Connect your smart phone to the Wi-Fi network created by the drone.
Check the drone’s status in the ”Attop View” app.
②Your smartphone will launch a search of the available Wi-Fi networks:
③Select the Wi-Fi network: W80-XXXXXX
④Wait for several seconds until your smartphone connects to the drone's Wi -Fi
network.
This connection is generally represented by the Wi-Fi logo appear-
ing on your smartphone’s screen.
W80-XXXXXX
Pairing
①First, press the drone Power Switch and quickly release. Then, press again
and hold for approximately 2 seconds. The drone will emit a sound and the
battery LEDs will brightly illuminate indicating it is now powered up.
Place the drone on a flat, level surface with the head facing forward.
②Turn on the switch on the controller by sliding it to the top. Once the
controller emits "beep-beep" sound, it confirms that the drone and controller
are now successfully paired.
OFF ON

-19-
Calibrating the Compass
After successful pairing, the drone LED lights flash rapidly. You can now
begin compass calibration.
Step 1:
Now, the app interface displays the above diagram and the Compass
calibration icon in controller screen is flashing. Hold the drone horizon-
tally and rotate the drone in approximately 3 complete circles. When
completed, the controller emits a “beep” sound and the drone's LED lights
flash slowly.
●Push Left Stick to top right corner and Right Stick to top left corner
simultaneously to activate Compass calibration (Pic), when operate
the drone and app at first time.
●Compass calibration will be activated automatically after rebooting
30 times.
●Retrun the drone when the app warns ”Geomagnetic anomaly,
please leave the source of interference and recalibrate the
compass!”.
Please move to open space without interference to operate the drone.
Push left stick to top right corner, right stick to top left corner simulta-
neously for activate compass calibration.
Attentions:
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Front lights
Rear lights
flash rapidly flash slowly
⑤Launch the Attop View application.
> The connection between your smartphone and the drone will be
established automatically.