Scytek electronic A777 User manual

VEHICLE SECURITY AND REMOTE
ENGINE START SYSTEM
PRODUCT MANUAL
FOR REMOTE START
SOME CARS MAY REQUIRE
SARTLINK RELAY PACK

A777, A20, G777, G27 Page 2
This vehicle security system is warranted to the original purchaser, to be free from defects in
material and workmanship. The manufacturer will repair or replace at its option, and free of
charge for the first twelve (12) months, any part that proves defective in material or workmanship
under normal installation, use, and service, provided the product is returned to the manufacturer
freight prepaid. After the first 12 month warranty period there will be a maximum service charge
of $50.00 per calendar year (if required) for repair and/or replacement of any defective parts.
A copy of the original purchase and installation receipt must accompany any products
returned for warranty service. Warranty is limited to defective parts and/or replacement parts
only and excludes any incidental, and consequential damages connected therewith.
The manufacturer of this theft deterrent system makes no warranty against the theft of the vehicle
or its contents. This warranty is not to be construed as an insurance policy against loss.
WARRANTY OF INSTALLATION LABOR, REMOVAL AND RE-INSTALLATION CHARGES ARE
NOT THE RESPONSIBILITY OF THE MANUFACTURER.
Note: This Warranty is voided if the product was not installed by an
Authorized ScyTek Dealer.

Page 3 - A777, A20, G777, G27
T5-2W-KIT
Two Way Pager upgrade kit
Easy Plug and Play upgrade to a complete two way system.
Increases range
MobiLink
Smart phone upgrade
Easy Plug and Play upgrade through the DBP (Data Bus port)
2 Way confirmation
Arm/Disarm
Remote Start On/Off
Trunk Release
Tracking
Alert Notification by SMS and Email

Button 1 Lock/Arm
Button 4 Start
Button 3 Trunk Release
Button 5 Conf/Shift
Button 2 Unlock/Disarm

Page 2 - A777, A20, A15, G777, G27
Remote Transmitter Description
The G777,G27,A777,A20 is supplied with 5-button Remote Transmitter used to control system
operations.
Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic
feature. Button 1 also locks the doors when the system is in Valet Mode.
Button 2 Disarms and Unlocks* the system. Pressing Button 2 again operates the Passenger Unlock
feature (if installed). Button 2 also unlocks the doors when the system is in Valet Mode.
Button 3 Activates the Auxiliary 1 output. This output will remain on for as long as the button is
pressed.
Button 4 press for 2 seconds Activates remote starter.
Shift then button 4 Activates the Auxiliary 2 output. This output will remain on for as long as the
button is pressed.
Button 5 is the Page Shift button. The Page Shift button will change the function of Buttons 1
through 4 each time it is pressed, allowing access to additional features or multiple car operation.
Each time the Shift Button is pressed, the LED on the transmitter will illuminate and the
transmitter functions will shift to the next page, allowing access to another set of features. Once
shifted to another page (there are 4 pages total), the transmitter will remain on that page for 10
seconds or until a button is pressed, then return to page 1. Each time a transmitter button is
pressed and held, the LED will flash a number of times to indicate from which page it is
transmitting. Under normal operation, only pages 1 and 2 are used. Pages 3 and 4 are usually
used for 2 nd. Car Operation.
Shift then Button 1 Arms and Locks* the system silently.
Shift then Button 2 Disarms and Unlocks* the system silently.
* If the Optional Keyless Entry Feature is installed.
Button 1 Arm
Button 3 Trunk release
Button 2 Disarm
Button 4 Start
Button 5 Shift

A777, A20, A15, G777, G27, A15 Page 3
Adding/Replacing One-Way Transmitters
To replace lost or stolen transmitters or to add additional transmitters into the system, have all
desired transmitters ready and follow the steps below.
Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously
stored transmitter code will be erased if it is not programed within the following sequence.
To program the transmitter(s):
1. Turn on the ignition key On, Off, On, Off, and back On.
The siren will chirp 3 times.
2. Press and hold the Override switch for 5 seconds.
The siren will chirp 5 times.
The LED will illuminate.
3. Press Button 1 on the first transmitter.
The siren will chirp once.
4. Repeat step 3 for each transmitter (up to 4).
5. Turn off the ignition key.
Battery Replacement
Your one way Remote Transmitter uses one battery type CR2032 for G777,G27,A777,A20,A15
which will require replacement in time. Depending on the amount of use, the battery may last up
to 48 months or more before it needs replacement.
When the battery needs replacing, the system’s operating range will decrease or the transmitter
LED may be off or not be as bright.
In order to change the battery, first remove 2 screws from the back of the transmitter and
separate the top and bottom halves of the case.
While replacing the battery make sure that the positive and negative terminals are positioned
correctly, then carefully reassemble the transmitter case.

Page 4 - A777, A20, A15, G777, G27
Remote Arming
The system monitors 4 independent areas (zones) while armed: doors, hood/trunk, shock sensor
and optional sensor input.
To Arm the System:
1. Turn off the ignition.
2. Press Button 1.
The siren will chirp once.*
The doors will lock.
The parking lights will flash once.
The LED will turn on, to indicate the starter defeat is activated.
3. 8 seconds after Arming:
The LED will start blinking to indicate that the doors and hood/trunk inputs are being
monitored.
* During Arming, if the system detects a bad sensor or an open zone, the system will chirp 4 additional times
and ignore that input, but keep all other areas protected.
Once Armed, the alarm will trigger when any of the following occurs:
The doors are opened.
The hood or trunk is opened.
The shock sensor detects an impact to the vehicle.
The optional sensor is disturbed.
When the alarm triggers, the siren will sound, the horn will honk, and the parking lights will
flash. If the system is triggered by the doors, or hood/trunk, the system will alarm for 45
seconds. If triggered by the shock sensor or optional sensor input, the system will alarm for
30 seconds.
In the event the alarm is triggered and remains triggered continuously by the same sensor
or input during a single arming cycle, that sensor or input will be automatically bypassed
until the next time the system is armed.
If the Shock Sensor detects a light impact to the vehicle, or the Optional Sensor’s warn-
away zone is disturbed, the siren will chirp 5 times as a warning indication.
Remote Disarming
To Disarm the System:
Press Button 2
The siren will chirp twice.*
The doors will unlock.
The parking lights will flash twice and remain on for 30sec..
The dome light will turn on.**
The LED will turn off.

A777, A20, A15, G777, G27 Page 5
If the system was triggered while away, the LED will flash to indicate which zone triggered the
system after disarming and turning on the ignition. The LED indication will repeat 8 times.
LED Flashes:
Silent Arming/Disarming
The system can be programmed to operate without Arm and Disarm chirp indications. When
programmed for full-time silent operation, the siren will sound only when the system is triggered.
The system is also capable of temporary silent operation if desired. Pressing the Shift button
before Arming or Disarming the system will bypass the chirp confirmations and allow one-time
silent operation.
Note: The open zone warning chirps will not be bypassed when the system is Armed or Disarmed silently.
Passive Arming
When programmed for the optional Passive Arming feature, the system arms itself automatically,
each time the ignition is turned off and all of the doors, hood, and trunk are closed.
To start the Passive Arming Process:
1. Turn off the ignition.
2. Open the door and exit the vehicle.
Once all doors are closed and the dome light is off, the LED will begin flashing rapidly.
Parking Lights will flash twice three seconds after passive arming cycle began.
3. After 30 seconds,
The siren will chirp.
The parking lights will flash.
The doors will lock.*
The status LED will begin flashing.
4. The system is now armed.
* If the Passive Locking feature is selected.
Panic Mode
In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly
trigger the alarm.
To activate the Panic Mode:
1. Press and hold Button 1 for 5 seconds.

Page 6 - A777, A20, A15, G777, G27
The alarm will sound.
The parking lights will flash.
The doors will unlock* allowing access to the vehicle.
2. Press Button 2 to stop Panic Mode.
* If the ignition is on when the Panic feature is activated, the doors will lock for personal safet
Emergency Override
If the transmitter becomes lost or inoperable, the system can still be disarmed using the following
procedure. Before beginning this procedure be sure to have the ignition key ready and know the
location of the override switch.
To Emergency Override the system:
1. Unlock the door using the key.
2. Enter the vehicle.
The system will trigger and the siren will sound.
3. Turn the ignition key on.
4. Press and hold the override switch until the system disarms.
5. The vehicle will now be able to start.
Optional Coded Emergency Override
As an extra measure of security, the system is equipped with an optional Coded Emergency
Override feature. Once an Emergency Override Code is chosen and programmed during
installation, the system can no longer be disarmed using the standard override procedure.
To Emergency Override the system using the Code:
1. Follow steps 1-3 above.
2. Press the override switch a number of times equal to the Disarm code, and continue
holding for 10 seconds on the last press.
The system will disarm. If the code is entered incorrectly, turn off the ignition and begin
again.
To set the Emergency Override Code:
1. Turn on ignition.
2. Within 5 seconds, press the valet switch 5 times.
The siren will provide one long chirp, indicating that you have entered Programming.
3. Press the valet switch 4 times.
The siren will chirp each time the valet switch is pressed.
4. Within 5 seconds, press Button 3 on the transmitter.
The siren will chirp 3 times.
5. Press the valet switch the number of time equal to the desired code (from 1-15).
6. Turn off the ignition then arm the system.
7. Disarm the system using the new Override Code to permanently store the new code.
Note: If the code set procedure is not properly performed, turn off the ignition and begin again. The override code will
not be permanently stored until the code is used to disarm the system.

A777, A20, A15, G777, G27 Page 7

Page 8 - A777, A20, A15, G777, G27

A777, A20, A15, G777, G27 Page 9
Validation/Brake Input Mode
Dome Light Output Mode.
Passenger Unlock Output Mode.

Page 10 - A777, A20, G777, G27

A777, A20, G777, G27 Page 11Page 11 - A777, A20, A15, G777, G27
FCC ID: OARRXAM2000
OARTXAM2000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation
19
20 Databus Input Triggers Enable Disable
21 Ignition2 Mode W/StartLink Ignition 2 Accessory 2 Starter 2
22 Starter Confirmation Chirps Disable Enable
23 Lock After Start On Off
24 Lock After Shutdown On Off
25 Unlock Before Start Disable Enable
26 Engine Run Timer 15 Minutes 25 Minutes
27 Automatic Start Mode 2 Hours 1 Hour
28 Crank Time Normal Extended Super Extended
29 Engine Sense Mode Smart sense/RPM Voltage sense only Smart Sense Monitor off
30 Engine Type Gas Diesel
31 Factory Alarm Upgrade W/park/L Enable
32 Factory Alarm Upgrade W/L/UNL Enable Enable with validation Disable
33 Validation/Brake Input Mode Validation Brake
34 Dome Light Mode Dome light Ignition Output
35 Passenger Unlock Mode Passenger Unlock Accessory Output

Page 12 - A777, A20, G777, G27
Positive Dome Light Activation Negative Dome Light Activation
Starter Defeat/Anti-Grind
Negative Horn Honk
Positive Horn Honk

A777, A20, G777, G27 Page 13
Negative Trigger
Reverse Polarity Vacuum
Adding Actuators
Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock
systems (separately unlocks driver and passenger doors) see following pages.
Positive Trigger

Page 14 - A777, A20, G777, G27
Two Stage Negative Trigger
Two Stage Positive Trigger
The Series is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock
operation. When connected as shown below, disarming the system will unlock only the driver’s
door. Pressing the disarm button again will unlock all doors.

A777, A20, G777, G27 Page 15
Two Stage Reverse Polarity
Two Stage Adding Actuators

Page 16 - A777, A20, G777, G27
FCC ID: OARRXAM2000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation
Built-in LED Light/Override/Valet/Call Switch into
the Antenna
Valet/Call/Override Switch
LED Light

11627 Cantara Street
North Hollywood, CA 91605
www.scytek.net
© ScyTek Electronics 2020 G777,G27,A777,A20,A15 7-15-20
Red (+) Constant Power Input
White (+)/(-) Selectable Light Flash Output
Brown (+) 2A Siren output
Blue/White (-) 500 mA Passenger Unlock Out (-)
White/Red (-) 500mA Channel 2 Output
Orange (-) 500 mA Armed Outpu
Brown/White (-) 500 mA Horn Output
Black/White (-) 500mA Dome Light Out
Blue (-) Hood/Trunk Trigger Input, (zone 5)
Gray (-) 500mA Channel 1 Output,Trunk
Yellow (+) Ignition In 12V
Black (-) Chassis Ground Input
Violet (+) Door Trigger Input, (zone 4)
Green (-) Door Trigger Input, (zone 4)
External Receiver Antenna G777/A777
Green Factory Alarm Upgrade Arm Input (+)
Red Factory Alarm Upgrade Disarm Validation Input (+)
Blue Factory Alarm Upgrade Disarm Input (+)
Remote Start: Some cars may require StartLink Relay Pack and
Data Bus Port: bypass Module, ADS ALCA
G777,G27
A777,A20,A15 Vehicle Security And Engine Starter Series.
Additional Optional Sensor (zone 2)
Valet /Override Switch (Blue Connector)
LED (Red Connector)
Green Lock Output (-) 500mA
Red Empty
Blue Unlock Output (-) 500mA
SCYTEK SECURITY/STARTER
BUILT-IN SMART SHOCK SENSOR
Harness Optional
For Detailed User & Installation Manual Refer To
www.scytek.net
For Built-In Scock Sensor adjustment refer to page 9