Se-Kure Controls Vantage II SK-584P User manual

Installation Instructions for the
SK-584P Vantage II Stand
w/Angled Sensor & Power Connection for T-Series + Power Alarms
Se-Kure Controls,
®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-[phone] • [phone] • Fax: [phone]
Rev. 11/12/09 SCI-9936©2009 Se-Kure Controls,
®Inc.
Optional Parts & Accessories
ASSEMBLY INSTRUCTIONS:
On the Web: www.se-kure.com
E-Mail: [email protected]
1. Remove the Security Screws
at the base of the Vantage II
Stand with the SK-11-309 Handle
Driver & SKP-190 Driver Bit or the
SKP-190T Security Wrench.
2. Remove the Base Plate
from the bottom of the
Vantage II Stand and place it
over the hole on the display.
3. Mount the Base Plate to
the display (Use the appro-
priate fasteners for your dis-
play surface).
4. Plug the SK-122-PWR-25
Alarm cable into the phone
jack in the base of the
Vantage II Stand.
To find the Adapter for
your device, contact your
Se-Kure Controls
Customer Service
Representative.
Fits Driver Above
SK-585
Angled Sensor Adhesive
SK-PS-126-S (shown)
Power Adapter
SKP-190
Security Screw Driver Bit
SK-11-309
Driver Bit Handle
SKD-584P
Vantage II Stand w/Angled
Sensor & Power
SK-122-PWR-25
2' Connecting Power Cable
SKP-190T
Security Wrench
SK-295P
12 Volt Power Supply
SK-T12P
T-12 Alarm Module w/Power
Follow the Battery
and Installation
Instructions that
come with your
Alarm Module.
Provides Power to the T-Series
Alarm & 5v to Connected
Devices

Se-Kure Controls,
®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-[phone] • [phone] • Fax: [phone]
Rev. 11/12/09 SCI-9922©2009 Se-Kure Controls,
®Inc.
On the Web: www.se-kure.com
E-Mail: [email protected]
5. Run the SK-122-PWR-25
Connecting Cable and the
power wire (from the bottom
of the stand) down through
the base plate & hole.
6. Replace the Stand onto the
mounted base plate and secure
it with the 3 security screws you
removed earlier. Use the security
bit driver or SKP-190T wrench.
7. Plug the SK-122-PWR-25
connecting cable into one of
the ports on the Alarm
Module.
8. Plug the SK-295P
Adapter into a standard 110v
live outlet somewhere nearby.
Standard
110v
Outlet
9. Clean the area on the
device where the sensor will
be applied with Alcohol Prep
Pads.
10. While the
Alcohol is still wet,
Dry the area
with a clean
paper towel.
11. Remove the Clear
Backing Sheet from the
Sensor Adhesive.
13. Plug the
Power Adapter
into power jack on the device.
14. Connect the power
cable on the sensor to the
Power Adapter you just
installed on the device.
Then place the device on
the stand.
12. Press the Sensor firmly
onto the device so it will align
properly on the stand.
SK-PS-126-S
Adapter
Follow the Battery
& Installation
Instructions
that came with your
Alarm Module.
To find the Adapter for your
device, contact your
Se-Kure Controls Customer
Service Representative.
Display Shelf
SK-T12P
Alarm
Module
SK-122-PWR-25
2' Connecting Power
Cable from the
Vantage II Stand
to the SK-T12 Alarm
Module
SK-295P Adapter
SK-584P
Vantage II
Stand with
GPS Unit
Completed Display

Installation Instructions for the
T-Series Alarm Systems w/Power
Se-Kure Controls,
®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-[phone] • [phone] • Fax: [phone]
Rev. 11/12/09 SCI-9936©2009 Se-Kure Controls,
®Inc.
Other Models Available
SK-T6P
T6 Alarm with
Power
SK-T12P
T12 Alarm
with Power
SK-295P
12 Volt Power Supply
Provides Power to the T-Series
Alarm & 5v to Connected
Devices
Sold Individually
Available on
SK-T6P-R & SK-T12P-R
Remote Keyway
Available on
SK-T6PK & SK-T12PK
T-Series w/Power & Keypad
Available on
SK-T6XP & SK-T12XP
Remote Horn
SK-110
Double Bit Keys
(6) “AA” Alkaline Batteries
(Not Included)
On the Web: www.se-kure.com
E-Mail: [email protected]
Battery Installation:
1. Remove the screw at the upper
right that holds the cover closed,
and unlock the cover with the key.
Special Note: Remote key units
only need to have the tamper screw removed.
2. Open the cover and install (6)
new “AA” Alkaline batteries, (3) on
each holder following the polarity
indicated on the battery holders.
3. Close the cover, lock the box,
and replace the screw that holds the cover.
Special Note: The AC/DC Power Supply is the pri-
mary power source and provides power to the
devices on the display. If power is cut off: the
alarm transfers to battery operation. Devices on the
display will lose power, but the alarm remains active
and will )))sound((( in an Alarm Condition if the bat-
teries are good.
(Optional)
Remote Key
Installation:
1. Determine the location on the display where
the remote key will be positioned.
IMPORTANT: (IN DETERMINING THE LOCATION)
The Remote Key Switch cable must be able to
reach from the Alarm Module to the Remote
Location.
2. The Key Cylinder fits
through a 3/4” hole
in the display surface,
and has a hex nut to
tighten it to the display
surface.
3. Plug the other end of remote key
switch into a T-Series Alarm
Module that has been equipped
with a remote key jack.
3/4" Hole
Hex Nut
Display
Factory Installed Optional Items

Installation Instructions for the
T-Series Alarm Systems w/Power
Se-Kure Controls,
®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-[phone] • [phone] • Fax: [phone]
Rev. 11/12/09 SCI-9936©2009 Se-Kure Controls,
®Inc.
On the Web: www.se-kure.com
E-Mail: [email protected]
Install the
AC/DC
Power Supply:
Plug the SK-295P AC/DC Power
Supply into a standard 110v AC
outlet and the other end into the
Alarm Module. The AC/DC Power
Supply is the primary power
source for the alarm and also pro-
vides power to the devices on the display.
Alarm Module Testing:
Install a sensor into any of the 6 or 12 sensor ports,
making sure the sensor is properly attached to a dis-
played device. Turn the key to the LEFT “ON” position.
WHEN THE UNIT IS TURNED ON: each port that
has a sensor plugged into it will flash for about 5 sec-
onds. At the end of 5 seconds, the green light at the
top of the Alarm Module will flash once and remain
on if AC Power is available.
The Red Light(s) Flashing for 5 Seconds
Indicates: that the unit located that sensor and it is
“Working Correctly”. In the Battery Mode the Green
Light that Flashes every 5 seconds Indicates: that
the unit is constantly checking the condition of the
batteries, and they are in GOOD Condition.
Low Battery Indication: The GREEN indicator Light
will continually flash along with a “BEEP” from the
horn, approximately every 10 seconds.
T-6/T-12 Alarm Operation:
Follow the Sensor installation instructions that came
with the Security Display Stands before setting up
the T-Series Alarm System. All of the Alarm Cables
should be connected to devices and ready to install
into the Alarm Module.
1. Turn the T-6 or T-12 Alarm Module Key to the
“Stand-By” Position. This is the position that you
cannot remove the key.
2. Connect the cables from displayed devices into
each of the 6 or 12 ports on the Alarm Module: (this
will be either SK-122-PWR-25 or SK-122-PWR45-25
cables).
3. When all of the cables have been connected, turn
the key to the LEFT “ON” position. The Alarm
Module will independently scan all (6) or (12) Sensor
ports for tampering. The unit also checks the AC and
battery power condition with a GREEN Light to show
it is operating.
The RED LED Lights on protected Sensors and the
corresponding RED LED Lights on the Alarm
Module Ports they are connected to will remain lit.
Tampering is the removal of Sensors from the Alarm
Module, from Merchandise, inserting Metal Objects
into Open Sensor Ports, or the attempt to short out a
sensor.
4. To Add or Remove a Device: insert the key into
the lock and turn it to the RIGHT “Stand-By” posi-
tion. While the unit is in the “Stand-By” mode, it will
“BEEP” once every 30 seconds to warn employees
to rearm the unit.
5. Add or Remove the Device Cable, and Turn the
key back to the LEFT “ON” Position. The Alarm
Module will re-scan all of the Sensor Ports and arm
itself.
During an “Alarm Mode”: Insert the key and turn it
to the RIGHT “Stand-By” Position. The RED
Indicator Lights will continue to flash, indicating
which sensor caused the alarm. Correct the problem
sensor that caused the alarm and turn the key back
to the LEFT “ON” Position. The T-Series Alarm will
always search through its ports and check battery
condition when turned to the “ON” Position.
SK-295P