ICW T2P2020 User manual

If you have any questions please call Toll Free 1-800-558-4435
ICWUSA.com, Inc.
t2P2020 installation
T2P2020 INSTALLATION 9/8/15 pjmPage 1 of 4
 MAXUMUM
LOAD 28 LBS
(12.7 KG)
Mount Arm to Track
When mounting to studs, ICW recommends using only wood or metal studs. This is the basic method to
mount the arm on a stud. Check building code regulations in your area for additional requirements.
The plastic straps and cap washer are positioning and
retention elements only. They do not otherwise function as
anchoring elements. Holding is dependent only on a metal
bolt to metal channel connection. The SnapToggle anchor
complies with all existing re codes for critical applications.
Handle Cap Straps Anchoring
Channel
Drill 1/2” hole. Hold metal
channel at alongside
plastic straps and slide
channel through the hole.
Minimum clearance behind
wall is 1-7/8”
Hold ends of straps together
between thumb and fore-
nger and pull toward you
until channel rests behind
wall. Ratchet cap along straps
with other hand until ange of
cap is ush with wall.
Place thumb between straps
at wall. Push thumb side
to side, snapping off straps
level with ange of cap.
Place track over ange.
Insert provided bolt and
tighten until snug against
track, then stop.
Snap Toggle Instructions
FOR WOOD STUD
Center mounting option
Locate the wall stud and mark the top center hole of the wall track. Drill a 11/64
pilot hole, insert a #14 screw and tighten slightly. Using a level, mark the lower
holes in the center of the track, drill pilot holes and then insert the #14 screws. Use
all screws.
Right or left mounting option
• Locate the wall stud. Align either right or left side of track with stud and mark one
hole in the upper corner for track placement. Drill 11/64” pilot hole. Insert #14
screw and tighten slightly.
• Using a level, mark the remaining holes on the same side, drill pilot holes into
stud. Insert #14 screws and, with the unit level, tighten screws.
• Insert provided Snap Togglers into outer corner holes on opposite side.
FOR METAL STUD
#14 wood screws are supplied with unit. If installing into metal studs you will
need to replace these with proper metal stud fasteners or provided snap toggles.
All hardware used to secure track mount must have a proper countersunk head.
MD tRaCK (also UsED FoR titan aRM)
attaCH BEaUtY CaP
After track installation
is complete, attach the
beauty cap using a
Phillips screwdriver.

If you have any questions please call Toll Free 1-800-558-4435
Page 2 of 4 T2P2020 INSTALLATION 9/8/15 pjm
t2P2020 installation
iF UsinG Wall MoUnt iF UsinG PolE MoUnt
iF UsinG DEsK MoUnt
attaCH Wall PlatE to Wall
Locate stud and mark top
hole, drill 11/64 pilot hole
and insert #14 screw and
tighten slightly. Using a
level, mark lower hole and
drill pilot hole, insert #14
screw and, with unit level,
tighten both screws. Insert
and tighten middle screw.
ICW supplies #14 wood
screws. If installing onto
metal studs, you will need
to replace with proper
metal stud fasteners.
attaCH PolE MoUnt to PolE
Detach the pole mount from arm using
the provided 5mm hex key. Separate
the two sections of the pole mount using
the provided 5/32 hex key. Place around
the pole you are mounting to and rmly
reassemble the pole mount.
Mount Arm to Wall, Pole or Desk
attaCH DEsK MoUnt to DEsK
Cords lay in groove
Detach desk mount
from arm. Feed cords
through the arm,
bearing and rotation
limiter, then through
the groove in the desk
mount.
Re-attach desk mount
to arm by screwing
button head bolt into
center hole of mount
from underneath.
Screw 3/8 All Thread
bolt into offset hole in
base of desk mount.
The bolt is included in
the hardware bag.
Drill a 3/8 hole through the horizontal
mounting surface. Push the All Thread
bolt on desk mount assembly through
the hole in the horizontal surface.
Slide large mounting washer over the
bolt from underneath and secure in
place with the 3/8 nylock nut.
Please follow cord management instructions before securing
desk mount to surface.
Use
offset hole
for All Thread
bolt
Mounting surface
Nylock nut
Mounting surface
Washer
Replace bolt in mount

If you have any questions please call Toll Free 1-800-558-4435
Page 3 of 4 T2P2020 INSTALLATION 9/8/15 pjm
t2P2020 installation
iF attaCHinG to UltRa FliP-UPiF attaCHinG to PaRalinK
Mount the Monitor
Attach Keyboard Tray
Attach VESA
to monitor
using four
4mm screws
in the
hardware
bag.
attaCH VEsa to
MonitoR (PaRalinK)
• Remove beauty cap
on Paralink.
• Remove screw using
3/16” hex key.
• Slide keyboard tray
into Paralink.
• Replace screw and
tighten.
• Replace beauty cap.
Beauty cap
Screw
attaCH PaRalinK
• Remove screws from
drop extension using
5/32” hex key.
• Align holes in
keyboard tray with
screw holes in drop
extension.
• Attach keyboard tray
using the provided
screws.
attaCH FliP UP
aDJUst PaRalinK tilt
Adjust monitor to
desired position with
ball VESA. Tilt monitor
50° in any direction.
Adjust monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
attaCH PaRalinK KEYBoaRD to MonitoR
Attach the paralink keyboard mount to the
monitor mount by using the 3/8-16 screw
and lock washer provided.
aDJUst Ball VEsa
tEnsion & HEiGHt
Use the slider knob to loosen the
slider to adjust the height of the
monitor on the Paralink.
Adjust the pivot tension of the ball
by gently and evenly tightening
or loosening the 4 screws on the
back of the ball VESA.
Slider Knob
Pivot tension
adjustment
screws

If you have any questions please call Toll Free 1-800-558-4435
Page 4 of 4 T2P2020 INSTALLATION 9/8/15 pjm
t2P2020 installation
Cord Management
• Using the Chrome 7/32 hex key
provided, disassemble arm as
shown and lay out on a at surface.
• Feed computer monitor cords and
any other cords through upper
arm, lower arm, wall mount and
all bearings. When feeding cords
through arms, keep them all to one
side of bolts at arm joints.
NOTE: When measuring for length
of cords, be sure to allow enough
extra cord to accommodate tilt and
rotation of monitor.
• Pass cords through slots in monitor
mount base plate and re-attach
monitor mount to front arm.
• Once all cords have been passed
through the arms, reattach arms
in the same order as they were
disassembled using the Chrome
7/32 hex key.
• Torque bolts down to 204 in/lbs
(17 ft/lbs).
NOTE: CORDS CAN BE DAMAGED IF
JOINTS ARE ROTATED MORE THAN
360º.
Bearing
Bearing
ManaGE CoRDs tHRoUGH aRM
WARNING: When disassembling the arms, the Chrome
7/32 hex key must be used. If a smaller hex key is used,
the bolt will strip.
Stop Pin
Stop Pin
Stop Pin
Rotation
Limiter Ring
aDJUst Rotation liMits
The rotation limits for the arm are
set by placing a stop pin in the
hole corresponding to where the
arm should stop. The stop pin
then bumps into the stop screw
under the arm segment, stopping
the arm. The stop pins can be
removed and set by hand.
Monitor with Paralink
keyboard tray
Monitor with Flip up
keyboard tray
Monitor only