SECURECOM V-4030PT-1 User manual

V-4030PT-1 INDOOR PAN/TILT
VIDEO CAMERA
Installation Guide
DESCRIPTION
The V-4030PT-1 is an indoor video
camera that allows for viewing live
and recorded video clips using
the Virtual Keypad™ App and
VirtualKeypad.com. The camera
can be connected using Wi-Fi or a
wired connection.
The camera can be set up to
automatically record when armed,
when motion is detected, or when
the system is in alarm, giving
immediate notification to the user.
Compatibility
• Any DMP system with an active
Virtual Keypad account
• V-IP1006RR SecureCom Wireless
Access Point (WAP)
What is Included?
• V-4030PT-1 Camera
• Camera Mounting Base
• Hardware Pack and Mounting
Template
• 5 V Power Supply
1MOUNT THE CAMERA
1. Use the included template to mark the screw holes for the
camera mounting base.
2. Secure the camera mounting base onto the surface using
the supplied screws.
3. Route any power and network cables through the mounting
base and connected them as necessary.
4. Secure the camera to the mounting base. See Figure 2.
Figure 1: V-4030PT-1 Video Camera
Figure 2: Mounting the Camera
Pan
Tilt
Open
Lock
Mounting
Base
POWER AND CONNECT THE CAMERA
2Using a SecureCom Wireless Access Point
Wireless Connection
1. Plug the 5 V power supply into the port on the back of the
camera, then connect it to a power outlet.
2. Press and hold the WPS button on the back of the WAP
for 2 seconds.
3. Press and hold the WPS button on the side of the
camera for three seconds. Once the camera and WAP are
connected, the LED on the WAP turns on steady.
Auto Pair
Verify the WAP is powered. Plug the 5 V power supply into the
port on the back of the camera, then connect it to a power outlet.
Auto-pairing begins immediately. Once the camera and WAP are
connected, the LED on the WAP turns on steady.

LT-1416 20151
V-4030PT-1 INDOOR PAN/
TILT VIDEO CAMERA
Specifications
Sensor and Lens
Image Sensor 1/3” CMOS
PIR Sensor Range 30-60 ft.
Resolution 960p (1280 x 960)
Network
Wireless IEEE 802.11b/g/n; WEP64/128 bit;
WPA/WPA2 Personal, WPS
Frame Rate Up to 30 fps
Video Compression H.264, Mpeg4/MJPEG
Hardware
Power Consumption 5 VDC, Max 8 W
Weight 3.09 lbs
Dimensions 5.51” H x 4.49” W
Ordering Information
V-4030PT-1 Wireless Access Point
Compatibility
Any DMP system with an active Virtual Keypad™ App
V-IP1006RR SecureCom Wireless Access Point (WAP)
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | DMP.com
© 2020
31. Log in to Dealer Admin (dealer.securecomwireless.com).
2. To open the System Information page, locate the customer and select their system account number.
3. To enable video, select Edit. Enable SecureCom Cameras & NVR, then press Save.
4. Press the Add Camera button and enter the 12-digit MAC Address located on the back of the camera.
Press Next.
5. Enter a name for the camera.
6. Select the camera’s time zone. If necessary, select Observe Daylight Savings Time.
7. If the camera image needs to be inverted due to mounting position, at Flip Image?, select Yes.
8. To allow this camera to record motion-triggered video clips, select Clips.
a. If you only want this camera to oer a live camera view through the Virtual Keypad app, choose
Never Record Motion.
b. If you want this camera to record video clips any time it detects motion, choose Always Record on
Motion.
c. If you want the camera to record motion-triggered clips only when the system is armed, choose
Record Motion When Armed.
9. To record video clips continuously during the first minute after the system triggers an alarm, select
Record on Alarm.
10. Press Save.
The device status is displayed next to the camera name. Refresh the page to display the latest status. When
the camera is active and communicating with SecureCom video servers, the status is displayed as Active and a
check mark is displayed in the Network Ready column.
To view the camera feed during installation, select the camera name under Video Devices on the System
Information page to display a live video feed for the first 60minutes after activation. This allows the user to
position the camera in the desired location. Once 60minutes has passed, the camera feed can only be seen
through the user’s Virtual Keypad app.
ACTIVATE THE CAMERA
Using a Non-SecureCom WAP
1. Plug the 5V power supply into the port on the back of the camera, then connect it to a power outlet.
2. Refer to the non-SecureCom WAP’s instruction manual to place the WAP in WPS mode.
3. After placing the non-SecureCom WAP in WPS mode, press and hold the WPS button on the side
of the camera for three seconds. Refer to the non-SecureCom WAP for connection confirmation
information.
Using a Hard-Wired Connection
1. Ensure there is Internet connection.
2. Plug an Ethernet cable into the LAN port on the back of the camera, then connect the other end to the
router or switch.
3. Plug the 5V power supply into the port on the back of the camera, then connect it to a power outlet.