SECURECOM V-4072 User manual

V-4072 MINI DOME INDOOR/OUTDOOR
WI-FI HD VIDEO CAMERA
Installation Guide
DESCRIPTION
The V‑4072MD is a 2 Megapixel
indoor/outdoor Wi‑Fi video camera
that allows users to view live and
recorded HD video clips in Virtual
Keypad™.
To activate the camera, you need
an active Dealer Admin account at
dealer.securecomwireless.com.
Compatibility
• Any active Virtual Keypad
account with SecureCom
Cameras & NVRs enabled
• V‑4000‑EXT10‑12V 10 foot
extension cable
What is Included?
• One V‑4072MD camera
• 12 VDC power supply
• Hardware pack
2MOUNT THE PLATE
1. After running the power
and/or network wires to
the location of the camera,
thread the wires through the
mounting plate.
2. Attach the mounting
plate to the ceiling using
the included screws and
standos from the small
hardware bag. See Figure 3.
Figure 1: Mini Dome Camera
ADJUST THE CAMERA
3Loosen the adjusment screw to turn the lense in the desired
direction of view using the lense adjustment wrench. Do not
remove the screw completely.
Figure 3: Mounting Plate
Adjustment
Screw
Figure 4: Camera Range of Motion
Lense
Adjustment
Wrench
1REMOVE THE COVER
Using the included L‑key to remove
the cover from the camera. Leave
the screws in the cover.
Figure 2: Remove Cover

2 V-4072MD INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
PLUG IN THE CAMERA
5Remove the cap from the end of the power
supply.
Standard Power Connection
Connect the included 12 VDC power supply and
optional extension cable to the camera power
connector. See Figure 6.
If you are not using Wi‑Fi, connect a network
cable to the camera Ethernet connector.
PoE Connection
Connect a network cable to the camera Ethernet
connector. On the other end of the connector,
connect the cable to a PoE switch or injector.
WIRE THE CAMERA
4Before connecting the Ethernet cable or PoE cable, install
the waterproof Ethernet cap if desired. Refer to Figure 5.
Figure 6: Ethernet and Power Supply
Ethernet/Wi-Fi
Power to Camera
Camera
Mounting Plate
Reset/WPS Button
Cap
Power Supply
MOUNT THE CAMERA
6Attach the camera to the mounting plate with
three included screws. See screw hole locations in
Figure 6.
Figure 5: Installing the Waterproof
Ethernet Cap
a
b

V-4072MD INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3
After you’ve connected the camera to Wi‑Fi or network, activate it in
Dealer Admin.
1. Log in to Dealer Admin.
2. Find the customer and select the system. Select Edit.
3. Verify that, in Video, SecureCom Cameras & NVR is enabled,
then press Save.
4. On the System Information page, press the Add Camera button
and enter the camera’s serial number. Press Next.
5. Enter a name for the camera.
6. Select the camera’s time zone and DST setting.
7. If the camera image needs to be inverted due to mounting position, toggle Flip Image.
8. Choose the desired video quality:
a. High = 1920 x 1080
b. Medium = 1280 x 720
c. Low = 640 x 480
9. To configure clip recording options, select Clips.
a. If you don’t want this camera to record video clips any time it detects motion, choose Never.
b. If you want this camera to record video clips any time it detects motion, choose Always.
c. If you want the camera to record motion‑triggered clips only when the system is armed, choose Only
When Armed.
10. To record video clips continuously during the first minute after the system triggers an alarm, enable
Record on Alarm.
11. Press Save.
Select one of the following connection methods and complete the appropriate steps to configure the camera.
Note: SecureCom recommends marking the Ethernet cable from the customer’s router to the WAP to help
with network troubleshooting.
Connect to a SecureCom WAP
Verify that the WAP is powered. Plug the camera’s 12 VDC power supply into a standard 120 V electrical
outlet. The camera starts auto‑pairing when powered.
Connect to a Router with WPS
You can also connect the camera to the WAP using WPS. See the following instructions:
1. Press and hold the Reset/WPS button on the camera for 3 seconds. See Figure 6 for button location.
2. Refer to the router’s instruction manual to place the router in WPS mode.
CONNECT THE CAMERA TO WI-FI
7
ATTACH THE COVER TO THE CAMERA
Attach the cover with the three screws already in the cover.
See Figure 7.
8
Figure 7: Attach Cover
ACTIVATE THE CAMERA
9

Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-2212 20322
V-4072 MINI DOME
INDOOR/OUTDOOR HD
VIDEO CAMERA
Specifications
Sensor and Lens
Image Sensor 2MP, 1/2.7” CMOS
Network
IP Protocol IPv4
Wi-Fi
Standard 802.11 B/G/N
Range Max 165 feet
Security WPA, WPA2
Hardware
Power Consumption
12 VDC Max 8.5 W
PoE (802.3af) Max 10.0 W
Weight 0.90 lbs (0.4 kg)
Dimensions 4.3” x 2.2” (11 cm x 5.64 cm)
Housing Material
Front cover Plastic
Mounting plate Plastic
Camera base Metal
Environmental
Operating Temperature -22° to 140° F (-30° to 60° C)
Operating Humidity 95% or less (non-condensing)
Ordering Information
V-4072MD Mini Dome Indoor/Outdoor HD
Video Camera
Accessories
371-500B-W Replacement 12 VDC Power Supply
V-4000-EXT10-12V Extention Cable (10 feet)
Compatibility
Any active Virtual Keypad account with SecureCom Cameras
& NVRs enabled
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803‑8877
800.641.4282 | DMP.com
© 2020
ADDITIONAL INFORMATION
Enable Email Clips
If the user would like to be emailed video clips, enable Email Video Clips in Dealer Admin. When this feature is enabled,
video clips are emailed to the app user.
1. Find the customer and select their name.
2. In App Users, find the user’s row, select the More icon, then select Edit.
3. Select Email Video Clips, then press Save.
Alternative Wiring Option
If you are running wires along the ceiling, instead of through it, remove the
knockout in the mounting plate before mounting.
Knockout
Figure 8: Knockout Location