Securitytronix ST-NVR4CH-I User manual
1
Thank you for your purchase of this SecurityTronix Network Video
Recorder (NVR). This Quick Start Guide covers the most essential
information for getting the NVR up and running. For more in-depth
information on the NVR’s functions the full manual is available in PDF
format at http://www.securitytronix.com/products
Getting Started
MAKING CONNECTIONS.................................................pg02
POWERING ON and SHUTTING DOWN.............................pg03
FIRST STARTUP............................................................pg04
LOGGING IN and LOGGING OUT......................................pg05
General Settings
SETTING DATE AND TIME..............................................pg07
CHANGING PASSWORDS................................................pg08
Record Settings
CAMERA DISCOVERY.....................................................pg10
SCHEDULING RECORDING..............................................pg11
CHANGING RECORD MODES...........................................pg13
Motion Detection
SETTING UP MOTION DETECTION...................................pg15
ADJUSTING MOTION REGIONS.......................................pg16
Playback and Backup
PLAYING BACK VIDEO...................................................pg17
BACKING UP VIDEO FILES.............................................pg19
Networking
NETWORKING THE NVR.................................................pg21
HOW TO ENABLE P2P....................................................pg22
MOBILE APPS...............................................................pg23
SOFTWARE..................................................................pg26
Troubleshooting
CONTACTING SUPPORT................................................pg28
2
Getting Started
MAKING CONNECTIONS
8 channel NVR shown. Identical configuration for 4/8/16/32CH NVR
1. Connect the network cable from the back of the NVR to
Network switch or PoE switch. (#1 in the image above)
2. Connect a monitor to the NVR using either the VGA port (#2 in
the image above) or the HDMI port (#3 in the image above) and the
appropriate cable.
3. Connect the included USB mouse to the rear USB port of the
NVR. (#4 in the image above)
4. Connect the included 12VDC power supply’s AC plug into an
appropriate AC power outlet which supplies between 110
and 120 volts AC. Then plug the power supply’s DC connector
into the NVR’s DC power input port. (#5 in the image above)
NOTE: An uninterruptable power supply is recommended
for the NVR and any power supplies for the cameras, both
to protect against damage from sudden power loss, and to
maintain video surveillance in the event of a power outage.
3
POWERING ON and SHUTTING DOWN
POWERING ON
Once all necessary connections to your NVR are made, toggle the
power switch on the back of the NVR to the ON position.
If the NVR does not automatically start, press the button on the
front panel of the NVR.
The POWER indicator light will be displayed on the NVR’s front panel.
It is normal for the NVR to sound a beep during startup.
SHUTTING DOWN
In the event that the NVR needs to be powered down, perform one of
the following to ensure a safe shutdown:
1. Enter the MAIN MENU (see page 5), select SHUTDOWN in the
OPERATION section, then select SHUTDOWN from the popup
window.
2. Alternately, press and hold the button on the front panel
of the NVR. The screen will show a progress bar for
shutdown.
4
Continue holding the button until the progress bar fills and
the NVR shuts off.
NOTE: In rare cases it may be necessary to remove power to the NVR
by disconnecting the power supply. However, this should be avoided
if possible, as removing power without properly shutting down the
NVR may corrupt and/or damage the hard drive. Only remove power
from the NVR if it will not respond to a shutdown through the
methods described.
FIRST STARTUP
The first time that your NVR is powered on, it will perform necessary
functions, such as properly formatting an unformatted hard drive for
recording, and it will display the STARTUP WIZARD. It is recommended
that you follow the steps in the popup window to simplify the NVR’s
initial setup.
5
The STARTUP WIZARD will take you through:
General Settings (more on page 7)
Network Settings (more on page 21)
Remote Device (IPCAM) Settings (more on page 10)
Recording Schedule (more on page 12)
The STARTUP WIZARD will be displayed each time the NVR is started.
If you do not wish for the STARTUP WIZARD to be displayed, click to
uncheck the STARTUP option before proceeding. You can also find this
option in the GENERAL SETTINGS (see page 7).
LOGGING IN and LOGGING OUT
LOGGING INTO THE NVR & MENU
From the NVR’s main screen, right-
click the mouse and choose MAIN
MENU from the drop-down menu.
The SYSTEM LOGIN window will
appear to prompt you to log in. Click
in the PASSWORD field or on the
keyboard icon to bring up the input
keyboard.
6
The default administrative accounts and passwords are:
USERNAME: admin PASSWORD: admin
USERNAME: 888888 PASSWORD: 888888
Using the mouse, enter the NVR’s password, then click ENTER or the
keyboard icon to close the input keyboard, then click OK to log in and
enter the menu.
It is strongly recommended to change the default passwords after
logging in the first time. (see page 8)
NOTE: If the password has been changed and forgotten or misplaced
it will be virtually impossible for the user to log into the NVR. In this
case please contact SecurityTronix at:
(610)429-1821, Press 3for Tech Support, then press 2.
In order to use the password reset service you must provide
credentials to verify that you are the authorized installer of this NVR.
LOGGING OUT
It is recommended to log out of
the NVR each time after use, to
prevent unauthorized access or
tampering.
From the MAIN MENU, select
SHUTDOWN in the OPERATION
section, then select LOGOUT from
the popup window.
7
General Settings
SETTING DATE AND TIME
From the MAIN MENU, select SYSTEM in the Setup section, then
select GENERAL from the options on the left side of the window, and
then select DATE&TIME from the tabs at the top.
Under SYSTEM TIME, click the Year to bring up the input keyboard,
then enter the current year using the mouse. When you are finished,
click outside the input keyboard to close it. Repeat these steps to set
the current Month and Day.
The same process is used to enter the current Hour, Minutes and
Seconds. This is necessary if video is ever offered up as evidence
against a corresponding cell phone tied to a global clock system.
8
Be sure to click SAVE next to the SYSTEM TIME to save Date and Time
settings before navigating away from the DATE&TIME menu.
If desired, the NVR can be set to automatically adjust the time for
Daylight Savings Time if your locality uses it. This is done by clicking
DST checkbox, then entering the dates Daylight Savings Time becomes
active in your area using the method described to set Date and Time
above.
When finished, click APPLY and then SAVE at the bottom of the
screen. This will return you to the MAIN MENU.
CHANGING PASSWORDS
From the MAIN MENU, select SYSTEM in the SETUP section, then
select ACCOUNT from the options on the left side of the window.
Click the pencil icon in the MODIFY column for the user account you
wish to change. This will open the MODIFY USER menu, which enables
9
you to make changes to an account’s permissions, name, group, and
password.
Click the MODIFY PASSWORD checkbox to select it, and then click in
the OLD PASSWORD field to bring up the input keyboard. Using the
mouse, enter the account’s current password, then click ENTER or the
keyboard icon to close the input keyboard.
Next, click in the NEW PASSWORD field, and enter a new password
using your mouse, then click ENTER or the keyboard icon. It is
recommended to use a combination of letters and numbers that is
hard to guess, easy to remember, and has not been previously used.
Once your new password has been created and entered, click in the
CONFIRM PASSWORD field and enter your new password once more
using the method above. The NEW PASSWORD and CONFIRM
PASSWORD fields must match exactly.
10
Once the new password is entered and confirmed, click SAVE at the
bottom of the MODIFY USER window to lock in the new password and
return to the ACCOUNT menu.
NOTE: It is strongly recommended to write down the new password
and keep it in a secure location. If the password has been changed
and forgotten or misplaced it will be virtually impossible for the user
to log into the NVR. In this case please contact SecurityTronix at:
(610)429-1821, Press 3for Tech Support, then press 2.
In order to use the password reset service you must provide
credentials to verify that you are the authorized installer of this NVR.
Record Settings
CAMERA DISCOVERY
NOTE: For this feature explanation, it is presumed that the NVR is
already properly connected to the network, and there are no data
restrictions in place preventing the NVR from communicating both
across the network, and outside to the WAN.
From the MAIN MENU, select CAMERA in the SETTING section, and
then select REMOTE on the left side of the window.
11
From this menu, you can search across the network for available video
sources. When using Securitytronix Eye View IP cameras, devices not
within the NVR’s network segment will be detected, and simply need
to be re-addressed to communicate properly with the NVR.
Click on to begin the Search process.
Cameras detected on the network will begin to populate. Form here
you can either double click the Camera IP to add it to the NVR channel
lineup, or you can click on the button to modify that IP
camera’s network settings.
Once the device is attached, you will see a green dot on the STATUS
field.
Repeat these steps until all IP cameras have been added to your NVR.
When all desired changes have been made, click APPLY at the bottom
of the screen, and then click SAVE to return to the MAIN MENU.
SCHEDULING RECORDING
From the MAIN MENU, select STORAGE in the SETTING section, then
select SCHEDULE on the left side of the window.
12
Select a channel number to edit using the CHANNEL drop-down menu,
or edit all channels at once by selecting ALL.
Select the type of recording you want to edit (REGULAR for constant
recording or MD for motion detection recording only), then click and
drag with the mouse to highlight the periods you want to add in the
24-hour timeline for each day.
If multiple days will share the same schedule, you may edit those days
all at once by clicking on the checkboxes to the left of the window. If
all days will share the same schedule, then select ALL. A chain link icon
will appear to confirm that the selected days are linked.
Once selections are made, any changes in one of the linked days’
timelines will affect all linked days.
To erase sections of schedule, select a recording type as described
above, then click and drag of highlighted areas on the timeline to
remove.
Areas with colored lines will record in their designated modes. Areas
without any colored bars will not record at all. For example: in the
schedule pictured below, Sunday will record constantly, Monday
through Friday will record only motion between 9AM and 5PM while
recording constantly all other hours, and Saturday will not record at
all.
13
When all desired changes have been made, click APPLY at the bottom
of the screen, and then click OK to return to the MAIN MENU.
CHANGING RECORD MODES
From the MAIN MENU, select STORAGE in the SETTING section, then
select RECORD on the left side of the window.
14
Use the mouse to select the desired recording type for each channel
number under the MAIN STREAM and SUB STREAM sections.
Alternately, you can select ALL next to the desired recording type to
set all channels to that record mode.
SCHEDULE will set cameras to record per a user-defined schedule. (see
page #)
MANUAL will set cameras to record constantly, regardless of any
recording schedule.
STOP will prevent recording altogether. Cameras will still be visible on
the main screen, or on remote live stream, but no data will be
recorded.
When all desired changes have been made, click APPLY at the bottom
of the screen, and then click OK to return to the MAIN MENU.
15
Motion Detection
SETTING UP MOTION DETECTION
From the MAIN MENU, select EVENT in the SETTING section, then
select DETECT on the left side of the window.
Note: Changes in this menu must be made per channel to avoid
possible recording conflicts.
Select a channel number to edit using the CHANNEL drop-down menu,
then click the ENABLE checkbox. Next click the RECORD CHANNEL
checkbox, then click the corresponding RECORD CHANNEL number to
highlight it (ie: if editing channel 1, select RECORD CHANNEL 1).
Repeat this process for all channels on which motion detection is
desired. When finished, click APPLY at the bottom of the screen, and
then click SAVE to return to the MAIN MENU, or continue on to the
next section to edit motion detection regions.
16
ADJUSTING MOTION REGIONS
From the DETECT menu (see page 15),select a channel number to edit
using the CHANNEL drop-down menu, then click the REGION SETUP
button.
Items in the REGION SETUP section will need to be adjusted to meet a
balance of recording needs and environment, and therefore no exact
numbers or recommendations will be given.
By default, the entire screen will be red (enabled for motion detection,
REGION1). You can turn off areas of motion detection by left-clicking
on grid squares to remove the region color in any areas of the
camera’s view where motion detection is not desired.
Note: motion will not be detected by any portion of the screen not
covered by one of the region colors (red, yellow, blue or green).
By moving the mouse to the top of the screen, the REGION tabs and
sensitivity settings can be accessed. Each color corresponds to a
separate motion detection zone.
If multiple regions are desired, be sure to remove any other region’s
color from the new region’s area before adding the new region’s color.
For example: left-click to remove red (REGION1) from an area before
17
switching to yellow (REGION2) and filling in the new region. If regions
overlap, the region with the higher sensitivity setting will take priority
over the area.
Adjust SENSITIVITY (amount of change needed to trigger motion) by
left-clicking on the SENSITIVITY slider and moving left or right as
needed, with the left side being the lowest sensitivity, and the right
side being the highest sensitivity.
Adjust THRESHOLD (amount of time over which change must occur to
trigger motion) by left-clicking on the THRESHOLD slider and moving
left or right as needed, with the left side being the lowest amount of
time (instant), and the right side being the longest amount of time.
When all desired changes have been made, right-click to return to the
DETECT menu, click APPLY at the bottom of the screen, and then click
OK to return to the MAIN MENU.
Playback and Backup
PLAYING BACK VIDEO
From the NVR’s main screen, right-
click the mouse and choose SEARCH
from the drop-down menu OR from
the MAIN MENU, select SEARCH in
the OPERATION section.
At the top of the screen make sure
FROM R/W HDD is selected, then
click the button for REC.
18
In the calendar on the right side of the screen, select the date of the
video you wish to view. Days that have recorded video available will
have a light-blue background.
Next, select a channel number to view from the drop-down menu
below the calendar. You can switch between single camera and
multiple camera views by clicking the tabs above the channel drop-
down menu.
If there is recorded data on the selected day, portions of the timeline
at the bottom of the screen will appear colored according to the type
of recordings present.
Press the button to begin playback of the earliest recording in the
timeline.
Note: if viewing multiple channels, it is recommended to click the
SYNC checkbox, so that all channels always play the same time
periods.
19
You can navigate to other portions of the timeline by left-clicking
along the colored portions of the timeline to skip to that time.
To zoom in on a specific time period, click the approximate period on
the timeline you wish to view, then click one of the ZOOM buttons on
the bottom-right of the bottom of the screen to switch to the 24HR,
2HR, 1HR or 30MIN views.
When finished, simply right-click anywhere on the screen to exit
PLAYBACK and return to the main screen or MAIN MENU.
BACKING UP VIDEO FILES
From the PLAYBACK screen, locate the video files that you wish to
back up (see page 17), then click the VIDEO CLIP button (#1 in the image
below).
Then left-click and drag the BEGINNING TIME INDICATOR (#2 in the
image above) until it is approximately at the beginning of the video clip
you want to save. Next, left-click and drag the ENDING TIME
INDICATOR (#3 in the image above) until it is approximately at the end of
the video clip.
Note: moving the BEGINNING TIME INDICATOR and ENDING TIME
INDICATOR is not necessary if you wish to backup larger portions of
time, such as 30-minute or hour-long clips. If this is desired, simply
click the desired ZOOM button before clicking the VIDEO CLIP
button, and the entire visible timeline will be selected for backup.
Next, insert a USB thumb drive with into the front USB port on the
NVR. It is recommended to use a USB thumb drive without any files on
it. Once this is completed, click the BACKUP button at the bottom-
right of the screen (#4 in the image above).
1
2
3
4
This manual suits for next models
3
Table of contents
