Seiko SII Teriostar LP-1030-MF User manual

Wide Format Printer
Teriostar LP-1030 Series
LP-1030-MF
User's Manual for Multifunction Printer Operation
U00123006300
「セットアップ」
メニュー
4章
Be sure to read this manual carefully before use. It will enable you
tohandlethe Printer correctly.
After reading the manual, keep it in a place where you can access it
whenrequired.
Chapter
1
Before Use
Chapter
2
Copy Function Preset Functions
Chapter
3
Submission
Function
Chapter
4
Chapter
5
Scan Function
Chapter
6
Troubleshooting

U00123006300 January, 2011
© Seiko I Infotech Inc., 2011
All rights reserved.
The contents of this manual may be changed without prior notice.
This product displays fonts created by Ryobi and ARPHIC TECHNOLOGY.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive,
is statutorily obliged to be axed to the products.
In each directive, the scope of directive to be applied to equipment is explicitly dened. Our company’s
product LP-1030 series conforms the EMC directive (2004/108/EC)) and low voltage directive (2006/95/EC).
Inquiry of CE mark:
Seiko Instruments GmbH, French branch
European Head Oce
20 rue Jean Rostand, 91400 Orsay France
Tel: [phone]
Fax: [phone]
Seiko Instruments USA Inc., Infotech Division
2060 Wineridge Place, Suite A, Escondido,
CA 92029, USA
Tel : [phone]
Fax : [phone]
Seiko I Infotech Inc.
8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan
Phone : [phone]
Fax : [phone]

3
LP-1030-MF User's Manual for Multifunction Printer Operation
Your Printer is a Teriostar LP-1030 Series wide format Printer (Referred to
as the Printer in this manual), and this manual describes how to operate
the Printer's copy, submission, and scan functions.
For details about the print function, paper setting, consumable
replacement, and paper jam clearance, see the separate User's Manual for
Basic Printer Operation.
To handle the Printer safely and correctly, be sure to read the Safety
Precautions carefully before use.
After reading the manual, keep it in a safe place where it is accessed easily
when required.
Preface

4LP-1030-MF User's Manual for Multifunction Printer Operation
Safety Precautions
In this manual, the following symbols are used to alert the user to information that
will prevent damage to the Printer, and ensure its safe and correct use.
These symbols are explained below. Make sure that you thoroughly understand
the information. Always follow the instructions marked by these symbols.
Symbol Examples
Warning
If this information is ignored and the Printer is
handled incorrectly, it may result in serious injury or
death.
Caution
If this information is ignored and the Printer is
handled incorrectly, it may result in injury or machine
damage.
UThis symbol indicates that caution is required (includes dangers and
warnings).
The example on the left indicates a safety Warning or Precaution.
This symbol indicates a prohibited action.
The example on the left means Do not disassemble.
This symbol indicates required actions or instructions.
The example on the left means Disconnect the power plug from
the outlet.

5
LP-1030-MF User's Manual for Multifunction Printer Operation
Warning
Be very careful not to touch the fuser unit labeled HIGH TEMPERATURE inside
the Printer.
Burn injuries may result.
Do not disassemble or modify the Printer.
An accident or malfunction may result.
Do not heat a toner cartridge or a waste toner bottle containing waste toner, nor
place it into a ame.
It may burst or ignite, resulting in an accident or re.
Never use the Printer in a location exposed to abnormally high humidity or
moisture.
A re, electric shock, or malfunction may result.
Do not drop metal pieces such as staples, or spill water, or other liquids inside
the Printer or through gaps.
A re, electric shock, or malfunction may result.
Do not connect or disconnect the power cord or other parts with wet hands. An
electric shock may result.
In the following situations, turn o the power, and disconnect the power plug
from the outlet. If you continue using the Printer in an abnormal condition, an
accident or re may result.
When cleaning
When an abnormal odor, noise, or smoke is emitted
When foreign matter such as metal pieces or water get inside the Printer
or through gaps
When a problem that must be repaired by the service representative
occurs
Connect the power plug separately to a power socket with a rated voltage
of 120V and a rated current of 12A or more, or to a power socket with a rated
voltage of 230V and a rated current of 8A or more. To prevent a re or electric
shock, avoid the sharing of power with other equipment.

6LP-1030-MF User's Manual for Multifunction Printer Operation
Be sure to remove the dust on the power plug and the socket. Do not use a
dusty plug as a current leak due to humidity on its surface may heat the plug
and result in re.
Do not x, twist, bind, modify, stretch, or bend excessively the power cord. Do
not put heavy object on it. A damaged power cord may heat and result in re or
electrical shock.
If the power cord is cut or if the wires are exposed, ask a service representative
for replacement.
Using a damaged power cord may result in re or electrical shock.
Caution
Do not disassemble or modify the toner cartridge.
The toner on your skin will have a negative eect.
If ink stains your skin or clothing, wash with soap and water immediately.
To prevent a toner leakage, do not drop the toner cartridge nor expose it to strong
impacts.
If toner gets into your eyes, do not rub your eyes, and wash the toner out. Visit a
doctor immediately.
As the roll paper is heavy, handle it carefully to make sure that you do not drop it.
Dropping the roll paper on your feet may result in injury.
When installing the roll paper, use the cutter to cut the end of the paper. At this
time, be careful not to injure yourself on the cutter.
Install the Printer close to a power outlet. Make sure the outlet is easy to reach in
case the power plug needs to be disconnected in an emergency.
When connecting and disconnecting the power cord, hold it by the plug or
connector.
To prevent a re, electric shock, or malfunction, avoid pulling the cord.

7
LP-1030-MF User's Manual for Multifunction Printer Operation
If you use a power strip, change it for a new one at least once a year.
Do not use an extension cable or an adapter plug.
Once a month, turn the power switch o and inspect the followings. Contact your
service representative if you detect any problem.
The plastic insulator at the base of the plug's pins does not suer from heat
deformation.
The plug's pins are not bent or covered by rust.
There is no dust between the plug's pins.
The power cord is not frayed and the energized wires are not exposed.
The plug is rmly plugged into the socket.
There is no dust on the plug or the socket.
Before moving the Printer from its current installation location to another location,
contact your service representative.
In addition to the items above, observe the warnings and precautions in each
section of the manual.

8LP-1030-MF User's Manual for Multifunction Printer Operation
Reading the Manual
Notations
Indicators
Warning
Describes information equivalent to a Warning in a safety precaution.
Caution
Describes information equivalent to a Caution in a safety precaution.
Note
Describes the information to be noted on handling the Printer.
TIP
The Tip indicator.
Indicates useful information, supplementary operation, or other information.
(&page) The Reference indicator.
The reference section or page is shown after this indicator.

9
LP-1030-MF User's Manual for Multifunction Printer Operation
Table of Contents
Preface
Chapter 1
Before Use
TCopy Restrictions.........................................................................................14
TAbout the Multiple Functions...................................................................15
Print Function ........................................................................................................................ 15
Copy Function....................................................................................................................... 15
Submission Function......................................................................................................... 15
Scan Function........................................................................................................................ 15
TMain Functions ............................................................................................16
TAbout Originals ...........................................................................................19
Scannable Original Conditions.................................................................................... 19
Unscannable Originals...................................................................................................... 19
Using Carrier Sheets with Originals ..........................................................................20
Guaranteed Image Scan Range.................................................................................. 21
TLoading the Original...................................................................................22
Loading the Original..........................................................................................................22
Canceling Original Scanning ........................................................................................24
TRegular Cleaning .........................................................................................26
Cleaning the Shading Guide and Scanner Glass..............................................26

10 LP-1030-MF User's Manual for Multifunction Printer Operation
Chapter 2
Copy Functions
TCopy Operation Flow..................................................................................28
TCopy Function Overview ...........................................................................30
TSelecting the Original Type.......................................................................31
TAdjusting the Density.................................................................................32
TSelecting the Paper Position.....................................................................33
TSelecting the Original Size ........................................................................34
TSelecting the Original Size Standard.......................................................38
TSelecting the Original Output Direction ................................................39
TPartial Copying ........................................................................................... 40
TAdjusting the Background ........................................................................42
TAdjusting the Original's Contrast.............................................................43
TAdjusting the Original's Sharpness......................................................... 44
TPerforming White on Black Reverse ........................................................45
TSetting the Scale......................................................................................... 46
TAdding Blank Space....................................................................................47
TSelecting the Paper Type .......................................................................... 48
TErasing the Frame .......................................................................................49
TSelecting the Paper Output Slot ..............................................................50
TPerforming Mirror Reverse........................................................................51
TEntering the Number of Copies................................................................52
TPerforming a Moderate Scan ....................................................................53
TCopying an Original with Text & Lines ....................................................54
TCopying a Blueprint Original ....................................................................55
TSorting...........................................................................................................56
TInitializing the Setting................................................................................57
THandling copy jobs .....................................................................................58