Seneca SURPRISE User manual

EN
INSTALLATION MANUAL
SURPRISE Smart Display
Display HMI touchscreen with IoT, Gateway built-in I/O
SENECA s.r.l.
Via Austria, 26 – 35127 – PADOVA – ITALY
Tel. [phone] - Fax [phone]
For manuals in other languages and conguration software, visit:
www.seneca.it/products/surprise-smart-display
MI00542-1-EN 1/6
DOCUMENTATION

192mm
127mm
32mm
MODULE LAYOUT
Dimensions (LxHxD) 192 x 127 x 32 Weight 420 g Protection rating IP 64
2/6
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualied electricians. Specic documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.
The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.

GENERAL SPECIFICATIONS
Smart Display is a 7-inch HMI touch-sensitive colour display (capacitive touch panel), with 800 x 480
resolution and LED backlight.
It is also an operator terminal designed to control and monitor the operation of devices, systems or
production lines.
Smart Display also offers extended connectivity thanks to the functionalities of Industrial Gateway, Serial
Device Server, Bridge and optional WIFI.
The preloaded software application allows the display of parameters, the sending of commands, the
conguration of tags, communication, individual video pages and alarm management.
TECHNICAL SPECIFICATIONS
STANDARDS
EN300 328 Wideband transmission systems.
EN301 489-17 EMC Specic conditions for Data Transmission Systems.
EN301 489-1 EMC Common technical requirements for radio equipment.
EN60368-1, EN62311 Safety
POWER SUPPLY
Voltage
Absorption
24 Vac/dc ± 10%
AC: Max. 16 VA, 10 W; DC: Max. 9W (maximum brightness)
N.B.: Arrange a power supply with at least 1.5 A inrush
DISPLAY
Resolution
Brightness
Contrast
Duration
Viewing angles
RTC
800 x 640, technology: TFT, 16 M colours
350 cd/m2
500 : 1
30000 h (backlight level = 5)
70° / 50° / 70° / 70° (Top, Bottom, Left, Right)
YES
CONNECTIONS
ELECTRICAL
1 removable terminal 3.5mm pitch 10-way, 1.5 mm2 max cable section
2 micro USB connectors
2 RJ45 connectors (Ethernet ports)
ENVIRONMENTAL CONDITIONS
Operating temperature
Humidity
Storage temperature
Protection rating
From -20°C to +55°C
10%– 90% non condensing.
From -30°C to +55°C
IP64 (referred to the front and with gasket installed)
COMMUNICATION PORTS
2 x Fast Ethernet 10/100Tx ports on RJ45
1 x RS232/RS485 software switchable serial port
1 x RS485 serial port
1 x USB OTG port
1 x USB serial port for debugging software
1 x Wi-Fi 802.11 b/g/n, band 2.4 ÷ 2,4835 GHz, max Output Power: 17 dBm (50 mW)
2 x General Purpose Input or Output channels
AUXILIARY VOLTAGE
INPUT/OUTPUT See explanatory diagrams on page 5
GENERAL PURPOSE I/O
Number of channels: 2
Input voltage: 0÷28 V Threshold ON > 9 V
Input impedance: 9 kΩ Threshold OFF < 4 V
ASSEMBLY Using xing brackets or wall bracket
The Declaration of Conformity ( DoC) is available at www.seneca.it/surprise-smart-display.
3/6

WAN LAN
TERMINAL BOARD 1-8
USB
OTG
USB
DEBUG
DISPLAY BACK
VIEW
DRILLED PANEL
FIXING
BRACKET
DRILLING THE PANEL
157mm
102mm
4/6
INSTALLATION REGULATIONS
For secure xing use all four brackets provided.
In case of use in environments with the presence of water, use the supplied gasket.
The minimum thickness of the panel is 1 mm and the maximum thickness is 15 mm.
For the assembly: make a rectangular opening on the panel measuring: W=157 mm x H=102 mm.
Place the display on a stable surface, screw the 4 studs into the threaded inserts of the display, insert the 4 brackets and
x them to the display using the 4 white knobs.
Fastening the brackets as in the gure allows the easy insertion into the opening made on the panel.
Insert the display into the panel opening and x it by turning the brackets as shown in the gure.
Be careful not to drop the panel during xing to avoid damaging it.
SW1
For wall mounting use the outer holes of the xing accessory as shown in the picture below
(N.B.: the wall mounting accessory is supplied already assembled to the instrument, in case of wall mounting it must be
removed avoiding to make levers in order not to damage the plastic):
N.B.: DO NOT INSTALL THE INSTRUMENT AT A HEIGHT EXCEEDING 2m.
WALL-MOUNTING REMOVAL OF THE ACCESSORY FIXING

Important: The upper power supply limits must not be exceeded, as this could cause
serious damage to the module. Switch the module off before connecting inputs and outputs.
To meet the electromagnetic immunity requirements:
- use shielded signal cables;
- connect the shield to a preferential instrumentation earth system;
- separate shielded cables from other cables used for power installations
(transformers, inverters, motors, induction ovens, etc...)
POWER SUPPLY
The power supply is connected to terminals 1 and 2.
The supply voltage must be:
24 Vdc (indifferent polarity) or 24 Vac.
Use a power supply with a minimum current of 1 A
GENERAL PURPOSE INPUT
The inputs are PNP type with internal power supply,
the gure alongside shows the connection.
To use the INPUT or OUTPUT function it is
necessary to congure the dedicated port through
the dedicated conguration page.
The inputs can also be activated in voltage,
ON > 9 V, OFF < 4 V
GENERAL PURPOSE OUTPUT
Connection with internal power
12 V / 50 mA per output.
Connection with external power
12÷24 V / 100 mA per output.
SERIAL PORTS
The device has a COM1 port congurable as RS232
or RS485 on terminals 7 and 8 and a COM2 RS485
port on terminals 9 and 10.
Power supply 1
Power supply 2
COM1 485B/232RX 7
COM1 485A/232TX 8
COM2 485 B 9
COM2 485 A 10
GND 4
Auxiliary voltage output 3
GND 4
GPIO1 5
GPIO2 6
GND 4
GPIO1 5
GPIO2 6
LOAD
LOAD
ELECTRICAL CONNECTIONS
5/6
GND 4
GPIO1 5
GPIO2 6
0 V
Auxiliary voltage input 3
GND 4
GPIO1 5
GPIO2 6
LOAD
LOAD
12÷24 V
0 V
12÷28 V

WARNING
A wired emergency stop button must be installed in any human-machine interface system such as this
display in compliance with ICS safety recommendations.
If used as an operator panel for machines, check the applicable safety standards.
CAUTION
Do not power the HMI display and DC inductive loads or controller input circuits, with the same power
supply. Some controllers generate 24 Vdc but do not provide enough current to be able to power this
HMI display which, when turned on, generates absorption peaks greater than 1 A.
CAUTION
a. The length of the power cable must be kept to a minimum
(Max: 500m shielded, 300m unshielded).
b. If wiring occurs outdoors, use appropriate surge suppressors.
c. Properly separate the power conductors from the signal conductors.
CONTACT INFORMATION
Technical support [email protected]
Product information [email protected]
6/6
This document is the property of SENECA s.r.l. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modied or supplemented for technical and/or sales purposes.