Senix Cspx5-m User manual

58V MAX LITHIUM ION

CORDLESS POLE SAW

Operator’s manual

Model: CSPX5-M

For customer support, please call 1-800-261-3981 or send email to:

[email protected]

SAVE THIS MANUAL FOR FUTURE REFERENCE.

1WWW.SENIXTOOLS.COM

TECHNICAL DATA

TABLE OF CONTENTS TECHNICAL DATA

Model Number: CSPX5-M

Motor: 58V brushless Motor

Guide Bar: 10 in.

Speed (no load): 4800 RPM

Max Reach: 10 ft.

Oil Tank Capacity: 3.4 oz.

Saw Chain Model: 91PJ040X

Guide Bar Model: 100SDEA041

Chain Pitch: 3/8 in.

Chain Gauge: .05 in.

Drive Links: 40

Battery/Charger: B25X5/CHX5

Battery: 58V Max Lithium Ion, 2.5 Ah

Weight (w/ Battery): 12 lbs

Product Dimensions: 111 x 5.1 x 6.3 in. (extended)

77 x 5.1 x 6.3 in. (shortened)

TECHNICAL DATA��1

SAFETY

SPECIFIC RULES FOR THE POLE SAW��3

REDUCING KICKBACK ��4

SAWING TECHNIQUES��4

COMPONENT LOCATION

KNOW YOUR POLE SAW��5

ASSEMBLY

ASSEMBLY OF GUIDE BAR AND SAW CHAIN ��6

TENSIONING THE CHAIN ��6

SAW CHAIN LUBRICATION��7

FILLING THE OIL TANK �� 7

ATTACH /REMOVE THE BATTERY��7

OPERATION

ADJUSTING THE TELESCOPING HANDLE �� 8

TURNING THE POLE SAW ON AND OFF��8

PREPARATION��8

SAFETY WARNINGS ��8

MAINTENANCE

CLEANING ��9

REPLACING THE SAW CHAIN AND

GUIDE BAR��9

CHECKING THE AUTOMATIC CHAIN LUBRICATION��9

STORAGE ��9

PARTS

EXPLODED VIEW��10

PARTS ��12

WARRANTY

LIMITED TWO-YEAR WARRANTY��12

2 WWW.SENIXTOOLS.COM

SAFETY

Safety is a combination of common sense, staying alert

and knowing how your item works. SAVE THESE

SAFETY INSTRUCTIONS.

WARNING — To reduce the risk of injury, user must

read and understand operator’s manual.

WARNING — To avoid mistakes and serious injury, do

not use this tool until the following steps

have been read and understood.

1. READ and become familiar with this entire instruction

manual. LEARN the tool’s applications, limitations, and

possible hazards.

2. AVOID DANGEROUS CONDITIONS. Do not use in wet

or damp areas or expose them to rain. Keep work areas

well lit.

3. DO NOT use in the presence of ammable liquids

or gases.

4. DO NOT direct the tool at any bystanders.

5. KEEP BYSTANDERS AT A SAFE DISTANCE from the

work area, especially when the tool is operating. NEVER

allow children or pets near the tool.

6. DO NOT FORCE THE TOOL to do a job for which it was

not designed.

7. DRESS FOR SAFETY. Do not wear loose clothing,

gloves, neckties, or jewelry (rings, watches, etc.) when

operating the tool. Inappropriate clothing and items can

get caught in moving parts and draw you in. ALWAYS

wear non-slip footwear and tie back long hair.

8. WEAR A FACE MASK OR DUST MASK if working in

dusty or dirty conditions.

9. ALWAYS remove the battery from the tool when making

adjustments, changing parts, cleaning, or working on

the tool.

10. AVOID ACCIDENTAL START-UPS. Make sure the

power switch is in the OFF position before inserting

the battery.

11. REMOVE ADJUSTMENT TOOLS. Always make sure

all adjustment tools are removed from the tool before

turning it on.

12. NEVER LEAVE A RUNNING TOOL UNATTENDED.

Turn the power switch OFF. Do not leave the tool until it

has come to a complete stop.

13. NEVER STAND ON A TOOL. Serious injury could

result if the tool tips or is accidentally hit. DO NOT store

anything above or near the tool.

14. DO NOT OVERREACH and DO NOT cut above

shoulder height. This helps prevent unintended tip

contact and enables better control of the pole saw in

unexpected situations.

15. WEAR NECESSARY hand and hearing protection.

Wear no-slip heavy duty work gloves and hearing

protection in order to prevent injury.

16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools

clean and in good working order. Follow instructions for

lubricating and changing accessories.

17. CHECK FOR DAMAGED PARTS. Check for alignment

of moving parts, jamming, breakage, improper

mounting, or any other conditions that may a󰀨ect the

tool’s operation. Any part that is damaged should be

properly repaired or replaced before use.

18. DO NOT operate the tool if you are under the inuence

of drugs, alcohol, or medication that may a󰀨ect your

ability to properly use the tool.

19. USE SAFETY GOGGLES AT ALL TIMES that comply

with ANSI Z87.1. Normal safety glasses only have

impact resistant lenses and are not designed for safety.

Wear a face or dust mask when working in a

dusty environment.

20. Use ear protection such as plugs or mu󰀨s during

extended periods of operation.

!

3WWW.SENIXTOOLS.COM

SAFETY

SPECIFIC RULES FOR THE POLE SAW

FOLLOW THESE RULES WHILE OPERATING

THE POLE SAW.

WARNING — Do not let comfort or familiarity with

product (gained from repeated use)

replace strict adherence to product safety

rules. If you use this tool incorrectly, you

can su󰀨er serious personal injury!

1. Use the pole saw for cutting wood only. Do not use this

tool for cutting plastic, masonry, etc.

2. Keep all parts of your body clear of the chain while the

saw is running. Before starting the saw, make sure the

chain is not touching any objects

3. Always hold the pole saw with your right hand at the rear

handle and your left hand at the front handle. Holding the

chain saw di󰀨erently (left hand on rear handle, right hand

on front handle) may a󰀨ect the balance of the saw and

will increase the risk of injury.

4. Wear eye and hearing protection. Other personal

protection equipment for the head, hands, legs and feet

is recommended.

5. Do not operate the saw while sitting or standing in a tree.

Make sure to have a safe stance at all time. Only use the

saw when standing on solid, safe and level ground.

6. When cutting a branch that is under tension, take into

account that the branch may spring back.

7. Use particular caution when cutting brush and young

trees. The thin material may get caught in the chain and

hit you or throw you o󰀨 balance.

8. Carry the switched-o󰀨 saw using the front handle with

the chain pointing away from your body. Always put on

the protective cover when transporting or storing the

chain saw. Carefully handling the saw greatly reduces

the risk of accidentally touching the sharp cutting chain.

9. Follow the instructions for lubrication, chain tension

and changing accessories. An improperly tensioned

or lubricated chain may either break or considerably

increase the risk of kickback.

10. Keep the handles dry, clean and free from gas, oil and

grease. Slippery handles may lead to a loss of control.

11. Never attempt to use an incomplete or altered saw.

12. This machine is not intended for use by persons with

an impaired physical, sensory or mental capacity or by

persons with insu󰀩cient pole saw knowledge

or experience.

13. Remain alert; pay attention to what you are doing and

proceed sensibly when working with an electric tool.

Do not use the machine if you are tired or under the

inuence of drugs, alcohol or medication.

14. Young persons under the age of 16 are not permitted to

operate this device.

15. Inspect the saw thoroughly before use for damage. If

any parts or pieces appear to be missing or damaged,

do not operate the saw.

16. Do not operate during adverse weather conditions,

particularly during lightening and rain.

17. Always make sure the chain tension is correct.

18. Only use properly functioning pole saws. Only work with

a saw chain sharpened according to regulations.

19. Never saw with the upper edge or tip of the guide bar.

20. Always hold the saw rmly with two hands.

21. Sawing wood under tension necessitates an increased

amount of caution. Wood that is suddenly released from

tension can react in a completely uncontrolled manner.

This can result in severe to deadly injuries. Such work

may only be performed by trained specialists.

22. The purpose of this pole saw is for limbing trees and

cleaning up branches. Do not push it beyond its limits

or its capacities.

!

4 WWW.SENIXTOOLS.COM

SAFETY

REDUCING KICKBACK

Kickback can occur when the tip of the guide bar

touches an object or when the wood closes in and

pinches the saw chain inside of the cut. Tip contact can

kick the guide bar up and back towards the operator.

WARNING — The danger of a kickback is greatest

when attempting to cut near or with the

guide bar tip. Always apply the saw as

atly as possible in order avoid a loss of

control during operation.

Pinching the saw chain along the top of the guide bar can

push the bar rapidly towards the operator. Either of these

reactions may cause a loss in control of the saw, increasing

the chances of serious personal injury. Do not rely on the

safety devices built into the saw.

Kickback is the result of tool misuse and/or incorrect

operating procedures. These conditions can be minimized

with the following steps:

1. Maintain a rm grip, with thumbs and ngers encircling

the pole saw handles. Both hands should be on the saw

with your body and arms in a position to resist

kickback forces.

2. Do not overreach and keep the work area free from

obstructions.

3. Only use replacement bars and chains specied by

Senix. Replace dull blades as necessary.

4. Do not let the tip of the guide bar contact any surfaces.

5. Keep proper tension on the blade at all times. Check the

tension at regular intervals. Remove the battery from the

tool before making any adjustments to the blade or

the tool.

6. Cuts should only take place while the chain is moving

at full speed. Do not turn the saw ON or OFF in the

middle of a cut. Use extreme caution when re-entering a

previous cut.

7. Cut one branch at a time. Do not attempt plunge or bore

cuts. Watch for shifting logs or other external forces that

could close a cut and pinch the chain.

8. Make a precut on the opposite side of the log to avoid

the blade from being pinched during operation as

another safeguard against kickback.

SAWING TECHNIQUES

WARNING — When removing branches, hold the

pole saw at an angle ranging from 0 to

60° in order to avoid being struck by a

falling branch. The saw should never be

operated directly above head.

Saw o󰀨 the lower branches on the tree rst. By doing so, it

is easier for the cut branches to fall to the ground.

• At the end of the cut, the weight of the saw suddenly

increases for the user since it is no longer being

supported by a branch. There is a risk of losing control

of the saw, so make sure to stay alert during the entire

sawing operation.

• Only pull the saw out of a cut while the saw is running.

By doing so, you prevent the chain from jamming in

the wood.

• Do not saw with the tip of the guide bar. Do not saw

into the branch formations (where the tree branches

outwards). This will impede the tree’s ability to heal.

• For sawing o󰀨 smaller branches, place the stop face

of the saw on the branch. This prevents unwanted

movements of the saw at the beginning of the cut. While

applying light pressure, guide the saw through the

branch from top to bottom.

• For sawing o󰀨 larger branches, rst make a relief cut.

Saw through 1/3 of the branch diameter from the bottom

to top using the top side of the guide bar. Then saw from

top to bottom for the other 2/3 using the bottom side of

the guide bar. Saw o󰀨 longer branches in sections in

order to maintain control over the location of impact.

!

5WWW.SENIXTOOLS.COM

COMPONENT LOCATION

KNOW YOUR POLE SAW

1

3

4

5

6

7

9

10

8

2

11

12

1 — Battery Slot1

2 — Safety Switch2

3 — Trigger

4 — Pole

5 — Telescoping Release Clasp

6 — Angle Adjustment Button*

7 — Oil Tank Cover

8 — Motor Housing

9 — Tension Adjustment Knob

(Outside Knob)

10 — Cover Release Knob

(Inside Knob)

11 — Guide Bar

12 — Saw Chain

1 Battery sold separately

2 On back or underside of pole saw

6 WWW.SENIXTOOLS.COM

ASSEMBLY/ADJUSTMENT

ASSEMBLY

WARNING — Remove the battery before inspecting,

adjusting, performing maintenance, or

cleaning the unit.

CAUTION: Always wear protective gloves when

handling saw chains.

ASSEMBLY OF GUIDE BAR AND SAW CHAIN

1. Loosen the cover release knob to release the chain

sprocket cover (Figure 1). Remove the chain

sprocket cover.

1

Figure 1 - Release knob

1 — Release knob

2. Place the chain in the groove of the outside edge of the

guide bar as shown.

Note: Make sure the chain’s direction of rotation is correct.

The blades on each cutting link on the upper side of

the cutting bar must be facing towards the tip of the

pole saw.

3. Insert the guide bar and chain into the mount on the

pole saw (Figure 2). In the process, guide the chain

around the pinion and hang the guide bar in the chain

tensioning bolts.

Figure 2 - Guide bar and chain installation

4. Adjust the chain tension. Mount and hand-tighten the

chain sprocket cover with the retaining nut.

TENSIONING THE CHAIN

WARNING — Remove the battery before inspecting,

adjusting, performing maintenance, or

cleaning the unit.

CAUTION: Always wear protective gloves when

handling saw chains.

1. Loosen the retaining nut of the chain sprocket cover by a

few rotations.

2. Adjust the chain tension by rotating the Tension

Adjustment Knob (the outermost knob on the cover

release knob). Clockwise rotation increases the chain

tension; counter-clockwise rotation reduces the chain

tension. The saw chain is correctly tensioned if it can be

raised approximately 2 mm from the center of the

guide bar.

2 mm

Figure 3 - Correct chain tension

IMPORTANT: Do not over-tension the chain: this will

lead to excessive wear and reduces the

life of both the bar and chain.

CAUTION: The saw chain must be tensioned properly

in order to ensure safe operation.

The chain tension is optimal if the saw chain can be lifted

(2 mm) from the center of the guide bar.

Because the saw chain heats up during operation, its

length can uctuate. Check the chain tension every 10

minutes of operation and adjust as necessary, particularly

for new saw chains.

TIP: The saw chain shortens when cooling down. Loosen

the saw chain after work is completed to elongate the

chain’s life and prevent possible damage.

!

7WWW.SENIXTOOLS.COM

ASSEMBLY/ADJUSTMENT

SAW CHAIN LUBRICATION

The pole saw features automatic chain lubrication. Never

operate the pole saw without saw chain oil. The use of the

pole saw without enough saw chain oil will damage

the unit.

Only use special saw chain oil. Other oils will run the risk

of damaging the unit and voiding the warranty.

Take note of temperature conditions. Using the saw at

various temperatures requires the use of di󰀨ering oils. To

ensure a su󰀩cient layer of lubricant at lower temperatures,

use liquid oil (low viscosity).

FILLING THE OIL TANK

1. Place the saw on a level surface. Clean the area around

the oil tank cap and then open it.

CAUTION: Make sure that no dirt gets into the oil tank

to prevent clogging in the oil nozzle.

2. Fill the oil tank with 3.4 oz. of saw chain oil (Figure 3).

1

Figure 4 - Oil tank

3. Close the oil tank cap.

ATTACH /REMOVE THE BATTERY

CAUTION: Only use a Senix-approved battery

and charger.

Note: The battery is not fully charged at the time of

purchase. Charge it fully before using it for the

rst time.

To insert the battery, slide it into the back of the unit until a

“click” is heard. Make sure the battery is fully inserted and

latched into position.

To remove the battery, press the release button and slide

the battery out.

WARNING — Do not insert or remove the battery while

the trigger is pressed or while the chain

is in motion.

!

8 WWW.SENIXTOOLS.COM

OPERATION

ADJUSTING THE TELESCOPING HANDLE

1. Unlock the telescope release lever so that the pole can

freely extend outwards and inwards.

2. Extend it to the desired length and lock the telescope

release lever to hold it in place.

TURNING THE POLE SAW ON AND OFF

To turn ON, hold the pole saw rmly with both hands. Press

and hold the safety switch located on the left-hand side of

the rear handle above the main power trigger.

Press down the trigger to turn it ON. The safety switch can

now be released.

To turn OFF, release the ON/OFF trigger switch.

PREPARATION

Before each use, check the following items to ensure safe

working conditions.

POLE SAW: Before beginning work, inspect the pole saw

for damage to the housing, the extension cable, the saw

chain and the guide bar. Never use an obviously damaged

machine.

OIL TANK: check the ll level of the oil tank. Also check

whether there is su󰀩cient oil available while working. Never

operate the saw if there is no oil or the oil level has dropped

below the minimum oil level mark in order to prevent

damage to the pole saw. On average, an oil lling is

su󰀩cient for approximately 10 minutes of cutting operation

(depending on the duration of pauses and the density of the

workpiece).

SAW CHAIN: check the tension of the saw and the

condition of the blades. The sharper the saw chain is,

the easier and more manageable operations will be. The

same applies to chain tension. Check the tension every 10

minutes of operation to maximize safety. New saw chains in

particular are subject to changes due to the heat created by

operation.

PROTECTIVE CLOTHING: make absolutely sure to wear

the appropriate close-tting protective clothing such as

chainsaw-protective pants, gloves and safety shoes. Wear

a safety helmet with integrated hearing protection and a

face guard to provide protection against falling and recoiling

branches.

HEAD ADJUSTMENT

The angle of the saw’s head can be adjusted anywhere

from 0 to 30 degrees by pushing down on the

Angle Adjustment Button. If you would like to change the

angle of the saw’s head, rst remove the battery and then

adjust to the desired angle.

SAFETY WARNINGS

• In order to ensure safe work, do not operate the saw at

an angle of over 60°.

• Never stand below a branch that is being sawed.

• Exercise caution when sawing both branches under

tension or branches that are splintering.

• Make sure to safe guard against the risk of injury from

falling branches and ying wood projectiles.

• If the machine is in operation, keep persons and animals

away from the danger area.

• The machine is not protected against electric shock

when coming into contact with high-voltage lines.

Maintain a minimum clearance of 30 feet from current-

carrying power lines to avoid life-threatening

electric shock.

• Do not expose the unit to rain.

• When working on an incline, always stand above or to

the side of the branch being sawed. Hold the machine

as close as possible to your body. By doing so, you

maximize your balance.

9WWW.SENIXTOOLS.COM

SAWING TECHNIQUES

MAINTENANCE

WARNING — Remove the battery before inspecting,

adjusting, performing maintenance, or

cleaning the unit.

CLEANING

• Brush or blow dust and debris out of the air vents using

compressed air or a vacuum. Keep the air vents free of

obstructions, sawdust, and wood chips. Do not spray,

wash, or immerse the air vents in water.

• Wipe o󰀨 the housing and the plastic components

using a moist, soft cloth. Do not use strong solvents or

detergents on the plastic housing or plastic components.

Certain household cleaners may cause damage or

cause a shock hazard.

• Routinely clean out the dust and debris that gathers

under the tension housing, the oil outlet, and around

the bar and the chain sprocket. Otherwise it can jam

up the sprocket, the chain, and the lubrication system.

REPLACING THE SAW CHAIN AND

GUIDE BAR

WARNING — Only use replacement bars and chains

specied by the manufacturer. Incorrect

replacement bars and chains may cause

chain breakage and/or kickback.

The guide bar must be replaced if the groove of the guide is

worn out or the spur wheel in the guide bar is damaged or

worn out.

1. Loosen the cover release knob to release the chain

sprocket cover (Figure 1). Remove the chain

sprocket cover.

CAUTION: Always wear protective gloves when

handling saw chains.

2. Lift the worn saw chain out of the tted slot in the

guide bar.

3. Place the new chain in this position, making sure the

teeth are facing the correct direction and that the edge of

the chain ts into the slot around the guide

bar.

4. Replace the cover and tighten the release knob. Adjust

tension before operating.

CHECKING THE AUTOMATIC CHAIN

LUBRICATION

Regularly check the functionality of the automatic chain

lubrication in order to prevent overheating and the

subsequent damage to the guide bar and saw chain

associated with it.

For this purpose, align the guide bar tip against a smooth

surface (board, cut-in of a tree) and allow the pole saw to

run. If an increasing amount of oil appears, the automatic

chain lubrication functions properly.

STORAGE

Examine the unit thoroughly for worn, loose or damaged

parts. If you need to repair or replace a part, contact Senix

customer service at 1-800-261-3981.

• Clean the unit before storing or transporting. Be sure to

secure the unit while transporting.

• Remove the battery from before storing.

WARNING — Shorting the battery terminals together

may cause burns or a re.

• When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another.

• Store the unit in a clean, dry place. Cover it in order to

provide added protection.

!

10 WWW.SENIXTOOLS.COM

MAINTENANCE

PARTS

EXPLODED VIEW

For replacement parts, email: [email protected].

11WWW.SENIXTOOLS.COM

PARTS

No. Part # Description Qty. No. Part # Description Qty.

1Battery (2Ah) 1 29 Female Terminal 2

2Battery Latch 1 30 Heat Shrinkable Tube (Female) 1

3Button Spring 1 31 Nozzle Assembly 1

4Electronic Components 1 32 Transparent Oil Tube 1

5Double Torsion Spring 133 Oil Pump Assembly 1

6Shaft 1 33-1 Oil Pump Assembly 1

7Left Handle 1 33-2 Oil Pump Tension Spring 1

8Safety 1 34 Flange Tapping Screw 2

9Spring 1 35 Heat Shrinkable Tube 1

10 Trigger 1 36 Self Tapping Screw 4

11 Trigger Spring 1 37 Motor Cover 1

12 Self Tapping Screw 22 38 Motor Assembly 1

13 Right handle 138-1 Fan Blade 1

14 Heat Shrinkable Tube 138-2 Brushless Motor 1

15 Copper Strip 16 39 Closing Plug 2

16 Self Tapping Screw 640 Right Housing 1

17 Cable Clamp 2 41 Oil Feed Seal 1

18 Spring Connecting Line 1 42 Countersunk Head Screws 4

19 Telescoping Clamp 1 43 Felted Wool 1

19-1 Brace 1 44 Tensioning Spring 1

19-2 Hexagon Nut 1 45 Sprocket 1

19-3 Pan Head Screws 1 46 Split Washer 1

19-4 Brace Ring 1 47 Oil Box Cap Assembly 1

20 Tube Assembly 148 Oil Box Assembly 1

20-1 Bassoon 1 48-1 Transparent Oil Tube 1

20-2 Large Ring 1 48-2 Oil Tank Joint Rubber Sleeve 1

20-3 Telescoping Clamp 1 48-3 Oil Tank Delivery Connection 1

20-4 Cylindrical Pin 1 48-4 Sponge 1

20-5 Quick Clamping Adjusting Bolt 1 48-5 Oil Box Joint Core Plug 1

20-6 Connecting Brac 1 48-6 Valve 1

20-7 Fixed Pin 2 48-7 Oil Tank 1

20-8 Locking Nut 1 49 End Cap Assembly 1

20-9 Flat Gasket 1 49-1 Knob 1

20-10 Locking Nut 1 49-2 Machine Screw 2

20-11 Countersunk Head Screws 1 49-3 Adjusting Knob 1

20-12 Washer 1 49-4 End Cover 1

20-13 In Pipe 1 49-5 Axis With Circlips 1

21 Button 1 49-6 Circle Wheel 1

22 Connecting Handle Of Left Casing 150 Push Pedal 1

23 Connecting Handle Of Right Casing 151 Seal Ring 1

24 Self Tapping Screw 252 Guide Bar 1

25 Driven Button 1 53 Pan Head Screws 1

26 Steering Button Spring 1 54 Chain Saw 1

27 Left Housing 1 55 Guide Bar Sleeve 1

28 Electronic Components 1 56 Charger 1

12 WWW.SENIXTOOLS.COM

PARTS

WARRANTY

LIMITED TWO-YEAR WARRANTY

Senix CSPX5-M User manual

Popular Pole Saw manuals by other brands