Shintaro Wireless Vibro Speaker User manual

Wireless Vibro Speaker
User Manual
Portable Wireless Vibro Speaker
User Manual

Response:
12W
Truewireless operation
9
5-8
9
10
11
Shintaro Wireless Vibro

Shintaro Wireless Vibro Speaker

V+/B/V-

A. One speaker pair with smart phone for the rst time
(1) Slide “ON/OFF/BT” switch to BT, you will hear the power-on
indicating sound and quick beeps. Please ignore the later beeps.Press
and hold until you hear ticks, then your speaker is ready for paring.
(2) . Make sure that the Bluetooth is activated on your smart phone,
scan bluetooth device under the name “True wireless stereo” and pair
with it, you will hear an indicating sound that means a successful
pairing and your phone shows the device is connected.
(3). Open the music player, press , and you can play music from
the speaker, then the speaker control the pause/play, next/previous
song by pressing , , .
(4). Long press till you hear a beep , dial the last number in your
phone call history Short press , answer a call when a phone comes
in, and press again, you can end the call.
Y
Truewireless operation
Single speaker connection instruction

(5). If your smart phone shows the device is connected, but no sound
when you play music or you can’t dial a phone number when you long
press , turn the smart phone Bluetooth o and turn on again, choose
“True wireless stereo” record², reconnecting by hand hearing an
indicating sound and your phone shows the device is connected.
connection succeeded, then play music or dial the call.
B. The speaker has paired with smart phone before
(1) Slide “ON/OFF/BT”switch to “ BT”, you will hear the power-on
indicating sound and three quick beeps.
(2) Open your smart phone and activate Bluetooth, click the paired
record² of "True wireless stereo", the smart phone and the speaker are in
pairing mode.
(3) Please follow 3-5 of Part A
A pair of speakers connection instruction:
A. A pair of speakers pair with smart phone for the rst time
Slide “ON/OFF/BT” to “BT”of both speakers, you will hear the power-on
indicating sounds and three quick beeps respectively. Press button
and hold at the same time until you hear three ticks , the speakers will be
in pairing mode for each other. The connection will be done with a
dierent indicating sound around 20 seconds. Then choose either of the
speakers, press button and hold until you hear two ticks ,then the
speaker is ready for pairing.
(1). Make sure that the Bluetooth is activated on your smart phone, scan
Bluetooth device under the name “True wireless stereo” and pair with it,
and you will hear an indicating sound that means a successful pairing
with your smart phone. The one connected with Smart phone will be the
Master speaker for left channel, and the other is slave speaker for right
channel.
(2). Open the music player, press , and you can play music from the
speaker, then the speaker control the pause/play, next/previous song by
pressing , , .
(3). Long press till you hear a beep , dial the last number in your
phone call history Short press , answer a call when a phone comes in,
6

and press again, you can end the call.
(4). If your smart phone shows the device is connected, but no sound
when you play music or you can’t dial a phone number when you long
press , turn the smart phone Bluetooth o and turn on again, press
“True wireless stereo” record, reconnecting by hand hearing a sound
indicating connection succeeded, then play music or dial the call.
B. The two speakers paired before:
(1) Turn on the two speakers by sliding the “ON/OFF/BT” to “BT”
respectively (the Interval time should be more than 1 seconds.), and the
two speakers will be automatically connected with an indicating sound .
(3) Set the Bluetooth on your smart phone, click the previous pairing
record “True wireless stereo”, you will hear an indicating tone around 5
seconds and your phone shows the device is connected around
(2) If the connection record was cleaned, please follow instruction A.
Notice:
(1) The one connected with your smart phone is the Master for the left
chennal, the other is the slave for the right chennal. Only the Master
speaker can redial the call(subject to the last number in call history) by
press and hold around 3 seconds
(2) If your smart phone shows the connection unsuccessful, but it can’t
play the music or dial the call. Please turn o the blue-tooth, repeat
above connection steps.
Note 1:
Open its own music player of the smart phone, press , and you can
play music from the speaker, then press , , , which can
control the pause/play, next/previous of your smart phone. But if the
music player is downloaded, which may not support the speaker control
of those functions on the phone.
Note 2:
If the paired record was deleted, please follow up the instruction A.
7

Note 3:
Iphone can connect with two bluetooth speakers at the same time.So
the phone can not pair with any other speakers when it has connected
with a pair of true wireless speakers,the sound will be intermittent
Note 4:
If you slide “ON/OFF/BT” to “ON”, Bluetooth is still on and ready for
pairing.If the speaker connect to your phone automatically,it can
pause/play, next/previous ,but there will be no sound.So you have to use
a USB cable to connect the speaker and play music.
Note 5:
The interval time between last turn-o and last turn-on should be longer
than 3 seconds
Note 6:
The longest distance between two speakers is around 5 meters without
barriers.There will be signal disconnection if the distance is longer or
there are some barrier between the two speakers.
Note 7:
When two pairs of true wireless speakers work at the place and at the
same time,or the sound will be intermittent.
Note 8:
If your body is too close to the speaker’s mic which is near to the
antenna ,it may interfere wireless transmission which causes signal
disconnection.Then please turn o all speakers and turn on just one pair
of true wireless speakers and reconnect to your phone.Make sure the
distance between the two speakers is within 5 meters and no barriers
between them.
8

Open bluetooth
Into pairing mode
9
End

10