ShotTracker WRIST & NET SENSOR User manual

You can’t improve what you don’t measure, which is why we’ve created
ShotTracker: the wearable tech that automatically tracks your shot
attempts, makes and misses.
ShotTracker is made of 3 components: a wrist sensor, a net sensor and
the ShotTracker App. When a shooter shoots, the wrist sensor sends a
signal that a shot was attempted. The net sensor sends a signal indicating
if the shot was made or missed. Both signals are sent to the mobile
device where the ShotTracker App keeps track of your shooting stats.
NET SENSOR WRIST SENSOR
SHOOTING SLEEVE
WRIST BAND
CHARGING UNIT
CHARGING CABLE
SOLD
SEPARATELY

First things first, you need to charge your ShotTracker sensors.
Your unit is shipped to you ready to charge; just needs to be plugged in.
Plug the charging unit into a USB outlet using the charging cable.
Place the wrist sensor in the charging unit so the charging
contacts in the sensor match the charging contacts in the charger.
The wrist sensor fits properly one direction in the charging unit,
blue side facing up.
CHARGING
SHOTTRACKER APP
Download the ShotTracker app from your app store. To get started,
you will need to create an account with ShotTracker.
The app will provide step-by-step videos and directions to get you
set up and ready to shoot. If you need more assistance, check out
our online support at support.shottracker.com.
1
2
3
4
1
2
Place the net sensor in the charging unit
so the charging contacts in the sensor match
the charging contacts in the charger. The
net sensor fits properly one direction in the
charging unit, blue side facing up.
The LED’s on the sensors are RED when
charging and GREEN when fully charged. YOUR UNIT SHOULD LOOK
LIKE THIS WHILE CHARGING.
OR
(SELECT TO VIEW A VIDEO)
*** Net Sensorbattery lasts about 3 months. Wrist sensorbattery
lasts about 8 hours (continuous use)

WRIST SENSOR
To poweron your wrist sensor, hold down the power button for 3 seconds.
The LED light should blink green every few seconds if the wrist sensor is
powered on.
POWER ON
SENSOR + WRISTBAND
In your ShotTracker App, go to Settings >> Wrist Sensor and select your
wrist sensor from the list. The sensor you select will blink consecutively
for 5 seconds.
***Both the net and wrist sensor must be connected with the app in order to track shots.
***If you switch between your wristband and shooting sleeve, we reccommend you re-train
your ShotTracker. Go to Settings >> Training Profiles.
***If you switch between your wristband and shooting sleeve, we reccommend you re-train
your ShotTracker. Go to Settings >> Training Profiles.
PAIR SENSOR TO APP
Inside your wristband, there is a pocket.
Slide your wrist sensor, blue side up, LED
lights first, in to the wristband pocket.
1Before you put your wrist sensor in to the sleeve or wrist band, make
sure your wrist sensoris poweredon and conencted to the app. Your
wrist sensor should be double-blinking every few seconds.
2
Slide your wristband on to yourshootingarm. The
ShotTracker logo should be facing away from you.
3
(SELECT TO VIEW A VIDEO)
SENSOR + SLEEVE
Flip yoursleeve inside out. Inside your
sleeve is a pocket. Slide the wrist sensor,
orange side up, arrow facing down, in to
the shooting sleeve pocket.
1Before you put your wrist sensor in to the sleeve or wrist band, make
sure your wrist sensoris poweredon and conencted to the app. Your
wrist sensor should be double-blinking every few seconds.
2
Flip your shooting sleeve back to normaland slide it on to your
shooting arm. The ShotTracker logo should be facing away from you.
3

NET SENSOR
You can power on your net sensor by taking a couple shots or shaking it a
few times. The LED light should blink green every few seconds if the net
sensor is powered on.
POWER ON
ATTACHING THE NET SENSOR TO THE NET
In your ShotTracker App, go to Settings >> Net Sensor and select your
net sensor from the list. The sensor you select will blink consecutively
for 5 seconds.
***Both the net and wrist sensor must be connected with the app in order to track shots.
PAIR SENSOR TO APP
Lower your basketball to it ‘s lowest setting to
safely attachthe net sensor. If you cannot
reach the net while standing, please ask an
adult to help.
1Before you attach your net sensor to the net, make sure your net
sensor is powered on and conencted to the app. Your net sensor
should be double-blinking every few seconds.
2
Open the net sensor by releasing the metal
ring clasp and lifting the blue lid.
Position the net sensor on the back of
the net. Center a knot in the middle of
the orange frame so that a string passes
through all four channels of the frame.
The blue lid should face the court. Pull
the ring down and close the blue lid.
3
4
5
(SELECT TO VIEW A VIDEO)
***To preserve battery, the net sensor turns off after 15 mins of no activity.

ADDITIONAL SUPPORT
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warning: Any changes or modifications to this device not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
ENGLISH
This devices complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
1.This device may not cause harmful interference;
2.This device must accept any interference received, including interference that may cause undesired
operation of the device.
FRENCH
Cet appareil est conforme à Industrie Canada une licence standard RSS exonérés (s). Son fonctionnement est
soumis aux deux conditions suivantes:1. Cet appareil ne doit pas provoquer d'interférences2. Cet appareil doit
accepter toute interférence reçue, y compris les interférences pouvant provoquer un fonctionnement
indésirable de l'appareil.
[email protected]
913.602.8797
SUPPORT.SHOTTRACKER.COM