
10
Cooking time
The cooking time for your dish can be set on the oven. When
the cooking time has elapsed, the oven switches itself off
automatically. This means that you do not have to interrupt
other work to switch off the oven. The cooking time cannot be
accidentally exceeded.
Example in the picture: cooking time 45 minutes.
1. Use the function selector to set the type of heating.
2. Set the temperature or grill setting using the temperature
selector.
3. Press the 0button twice.
0:00 is shown in the display. The time symbols light up and
the Narrow is next to x.
4. Use the @or Abutton to set the cooking time.
Default value for @button = 30 minutes
Default value for Abutton = 10 minutes
The oven will start up after a few seconds. The cooking time
counts down in the display and the Nx symbol lights up. The
other time symbols go out.
The cooking time has elapsed
A signal sounds. The oven stops heating. 0:00 is shown in the
display. Press the 0button. You can set a new cooking time
using the @or Abutton. Or press the 0button twice and turn
the function selector to the off position. The oven switches off.
Changing the cooking time
Use the @or Abutton to change the cooking time. After a few
seconds, the change is adopted. If the timer has been set,
press the 0button beforehand.
Cancelling the cooking time
Use the Abutton to reset the cooking time to 0:00. After a few
seconds, the change is adopted. The cooking time is
cancelled. If the timer has been set, press the 0button
beforehand.
Checking the time settings
If several time-setting options are set, the relevant symbols are
illuminated on the display. The time-setting options symbol is in
the foreground and preceded by the Narrow.
To call up the Vtimer, xcooking time, yend time or 0
clock, press the 0button repeatedly until the Narrow is next
to the relevant symbol. The display shows the value for a few
seconds.
End time
You can change the time at which you wish your dish to be
ready. The oven starts automatically and finishes at the desired
time. You can, for example, put your dish in the cooking
compartment in the morning and set the cooking time so that it
is ready at lunch time.
Ensure that food is not left in the cooking compartment for too
long as it may spoil.
Example in the picture: it is 10:30 am, the cooking time is
45 minutes and the oven is required to finish cooking at
12:30 pm.
1. Adjust the function selector.
2. Set the temperature selector.
3. Press the 0button twice.
4. Use the @or Abutton to set the cooking time.
5. Press the 0button.
The Narrow is next to y. The time when the dish will be
ready is displayed.
6. Use the @or Abutton to set a later end time.
After a few seconds, the oven adopts the settings and switches
to standby position. The display shows the time at which the
dish will be ready and the Narrow is next to the ysymbol.
The Vand 0symbols go out. When the oven starts, the
cooking time counts down in the display and the Narrow is
next to the xsymbol. The ysymbol goes out.
The cooking time has elapsed
A signal sounds. The oven stops heating. 0:00 is shown in the
display. Press the 0button. You can set a new cooking time
using the @or Abutton. Or press the 0button twice and turn
the function selector to the off position. The oven switches off.
Changing the end time
Use the @or Abutton to change the end time. After a few
seconds, the change is adopted. If the timer has been set, first
press the 0button twice. Do not change the end time if the
cooking time has already started to elapse. The cooking result
would no longer be correct.
Cancelling the end time
Use the Abutton to reset the end time to the current time. After
a few seconds, the change is adopted. The oven starts. If the
timer has been set, first press the 0button twice.
Checking the time settings
If several time-setting options are set, the relevant symbols are
illuminated on the display. The time-setting options symbol is in
the foreground and preceded by the Narrow.
To call up the Vtimer, xcooking time, yend time or 0
clock, press the 0button repeatedly until the Narrow is next
to the relevant symbol. The display shows the value for a few
seconds.