Siemens HB836GT 6 Series User manual

Oven
HB836GT.6
en User manual and installation instructions
Register your product on My Siemens and discover exclusive ser-
vices and offers.
siemens-home.bsh-group.com/welcome
The future moving in.
Siemens Home Appliances

en Safety
2
Table of contents
USER MANUAL
1 Safety....................................................................2
2 Preventing material damage ...............................4
3 Environmental protection and saving en-
ergy .......................................................................5
4 Familiarising yourself with your appliance ........6
5 Operating modes .................................................7
6 Accessories..........................................................9
7 Before using for the first time ...........................10
8 Basic operation ..................................................11
9 Rapid heating .....................................................11
10 Time-setting options..........................................12
11 Dishes.................................................................13
12 Childproof lock...................................................15
13 Sabbath mode ....................................................15
14 HomeConnect ...................................................15
15 Basic settings.....................................................17
16 Cleaning and servicing......................................18
17 Cleaning assistance...........................................20
18 Appliance door...................................................20
19 Rails ....................................................................23
20 Troubleshooting.................................................24
21 Disposal..............................................................26
22 Customer Service...............................................26
23 Declaration of Conformity .................................26
24 How it works.......................................................27
25 INSTALLATION INSTRUCTIONS .......................32
25.1 General installation instructions.......................32
1 Safety
Observe the following safety instructions.
1.1 General information
¡Read this instruction manual carefully.
¡Keep the instruction manual and the
product information safe for future refer-
ence or for the next owner.
¡Do not connect the appliance if it has been
damaged in transit.
1.2 Intended use
This appliance is designed only to be built
into kitchen units. Read the special installation
instructions.
Only a licensed professional may connect ap-
pliances without plugs. Damage caused by in-
correct connection is not covered under the
warranty.
Only use this appliance:
¡To prepare meals and drinks.
¡In private households and in enclosed
spaces in a domestic environment.
¡Up to an altitude of max. 4000m above
sea level.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced
physical, sensory or mental abilities or inad-
equate experience and/or knowledge,
provided that they are supervised or have
been instructed on how to use the appliance
safely and have understood the resulting
dangers.
Children must not play with the appliance.
Children must not perform cleaning or user
maintenance unless they are at least 15 years
old and are being supervised.
Keep children under the age of 8 years away
from the appliance and power cable.
1.4 Safe use
Always place accessories in the cooking com-
partment the right way round.
→"Accessories", Page9
WARNING‒Risk of fire!
Combustible objects that are left in the cook-
ing compartment may catch fire.
▶Never store combustible objects in the
cooking compartment.
▶If smoke is emitted, the appliance must be
switched off or the plug must be pulled out
and the door must be held closed in order
to stifle any flames.

Safety en
3
Loose food remnants, fat and meat juices
may catch fire.
▶Before using the appliance, remove the
worst of the food residues and remnants
from the cooking compartment, heating ele-
ments and accessories.
Opening the appliance door creates a
draught. Greaseproof paper may come into
contact with the heating element and catch
fire.
▶Never place greaseproof paper loosely
over accessories when preheating the ap-
pliance and while cooking.
▶Always cut greaseproof paper to size and
use a plate or baking tin to hold it down.
WARNING‒Risk of burns!
The appliance and its parts that can be
touched become hot during use.
▶Caution should be exercised here in order
to avoid touching heating elements.
▶Young children under 8 years of age must
be kept away from the appliance.
Accessories and cookware get very hot.
▶Always use oven gloves to remove ac-
cessories or cookware from the cooking
compartment.
When the cooking compartment is hot, any al-
coholic vapours inside may catch fire.
▶Only use small quantities of drinks with a
high alcohol content in food.
▶Open the appliance door carefully.
WARNING‒Risk of scalding!
The accessible parts of the appliance become
hot during operation.
▶Never touch these hot parts.
▶Keep children at a safe distance.
Hot steam may escape when you open the
appliance door. Steam may not be visible, de-
pending on the temperature.
▶Open the appliance door carefully.
▶Keep children at a safe distance.
If there is water in the cooking compartment
when it is hot, this may create hot steam.
▶Never pour water into the cooking compart-
ment when the cooking compartment is
hot.
WARNING‒Risk of injury!
Scratched glass in the appliance door may
develop into a crack.
▶Do not use any harsh or abrasive cleaners
or sharp metal scrapers to clean the glass
on the oven door, as they may scratch the
surface.
The hinges on the appliance door move when
the door is opened and closed, which could
trap your fingers.
▶Keep your hands away from the hinges.
Components inside the appliance door may
have sharp edges.
▶Wear protective gloves.
WARNING‒Risk of electric shock!
Incorrect repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶Only use genuine spare parts when repair-
ing the appliance.
▶If the power cord of this appliance is dam-
aged, it must be replaced by trained spe-
cialist staff.
If the insulation of the power cord is dam-
aged, this is dangerous.
▶Never let the power cord come into contact
with hot appliance parts or heat sources.
▶Never let the power cord come into contact
with sharp points or edges.
▶Never kink, crush or modify the power
cord.
An ingress of moisture can cause an electric
shock.
▶Do not use steam- or high-pressure clean-
ers to clean the appliance.
If the appliance or the power cord is dam-
aged, this is dangerous.
▶Never operate a damaged appliance.
▶Never operate an appliance with a cracked
or fractured surface.
▶Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶If the appliance or the power cord is dam-
aged, immediately unplug the power cord
or switch off the fuse in the fuse box.
▶Call customer services. →Page26

en Preventing material damage
4
WARNING‒Danger: Magnetism!
Permanent magnets are used in the control
panel or in the controls. These may affect
electronic implants, e.g. heart pacemakers or
insulin pumps.
▶Wearers of electronic implants must stay at
least 10 cm away from the control panel.
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶Keep packaging material away from chil-
dren.
▶Do not let children play with packaging ma-
terial.
Children may breathe in or swallow small
parts, causing them to suffocate.
▶Keep small parts away from children.
▶Do not let children play with small parts.
1.5 Halogen bulb
WARNING‒Risk of burns!
The bulbs in the cooking compartment get
very hot. There is still a risk of burning for
some time after they have been switched off.
▶Do not touch the glass cover.
▶Avoid contact with your skin when cleaning.
WARNING‒Risk of electric shock!
When changing the bulb, the bulb socket con-
tacts are live.
▶Before replacing the bulb, ensure that the
appliance is switched off in order to pre-
vent a potential electric shock.
▶Also unplug the appliance from the mains
or switch off the circuit breaker in the fuse
box.
2 Preventing material damage
2.1 General
ATTENTION!
Objects on the cooking compartment floor at over
50°C will cause heat to build up. The baking and
roasting times will no longer be correct and the enamel
will be damaged.
▶Do not place any accessories, greaseproof paper or
foil of any kind on the cooking compartment floor.
▶Only place cookware on the cooking compartment
floor if a temperature above 50°C has been set.
When the cooking compartment is hot, any water in-
side it will create steam. The change in temperature
may cause damage.
▶Never pour water into the cooking compartment
when it is still hot.
▶Never place cookware containing water on the
cooking compartment floor.
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶Allow the cooking compartment to dry after use.
▶Do not keep moist food in the cooking compartment
for a long time with the door closed.
▶Do not store food in the cooking compartment.
Leaving the appliance to cool down with the door open
will damage the front of neighbouring kitchen units over
time.
▶Always allow the cooking compartment to cool
down with the door closed after cooking at high
temperatures.
▶Take care not to trap anything in the appliance
door.
▶Only leave the cooking compartment to dry with the
door open if a lot of moisture was produced during
operation.
Fruit juice dripping from the baking tray leaves stains
that cannot be removed.
▶When baking very juicy fruit flans, do not pack too
much on the baking tray.
▶If possible, use the deeper universal pan.
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶Never use oven cleaner in the cooking compartment
when it is still warm.
▶Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
If the seal is very dirty, the appliance door will no
longer close properly during operation. This may dam-
age the front of adjacent kitchen units.
▶Keep the seal clean at all times.
▶Never operate the appliance if the seal is damaged
or missing.
Sitting or placing objects on the appliance door may
damage it.
▶Do not place or hang objects on the appliance door.
▶Do not place cookware or accessories on the appli-
ance door.
With certain models, accessories may scratch the door
pane when closing the appliance door.
▶Always push accessories fully into the cooking com-
partment.

Environmental protection and saving energy en
5
3 Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶Sort the individual components by type and dispose
of them separately.
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Only preheat the appliance if the recipe or the recom-
mended settings tell you to do so.
¡Not preheating the appliance can reduce the en-
ergy used by up to 20%.
Use dark-coloured, black-coated or enamelled baking
tins.
¡These types of baking tin absorb the heat particu-
larly well.
Open the appliance door as little as possible during
operation.
¡This will maintain the temperature in the cooking
compartment and eliminate the need for the appli-
ance to reheat.
When baking multiple dishes, do so in succession or
in parallel.
¡The cooking compartment is heated after baking
the first dish. This reduces the baking time for the
second cake.
If the cooking time is relatively long, you can switch
the appliance off 10minutes before the cooking time
ends.
¡There will be enough residual heat to finish cooking
the dish.
Remove any accessories that are not being used from
the cooking compartment.
¡Accessories that are not being used do not need to
be heated.
Allow frozen food to defrost before cooking.
¡This will save the energy that would otherwise be
required to defrost it.

en Familiarising yourself with your appliance
6
4 Familiarising yourself with your appliance
4.1 Control panel
You can use the control panel to configure all functions
of your appliance and to obtain information about the
operating status.
Note:On certain models, specific details such as col-
our and shape may differ from those pictured.
1 2
3
1
1
Buttons
The buttons on the left- and right-hand side of
the control panel have a pressure point. Press
a button to execute its function. On appliances
without a stainless steel front, the buttons are
also touch fields.
2
Rotary selector
You can turn the rotary selector without limits
clockwise or anti-clockwise.
Touch fields are touch-sensitive surfaces. To
select a function, simply press lightly on the rel-
evant field.
3
Touch display
You can see the current selection options in the
touch displays. To select a function, press dir-
ectly on the corresponding field. The text fields
change depending on the selection.
4.2 Buttons
Use the buttons on the left- and right-hand side of the control panel to switch your device or the operating mode on
and off.
Button Function Use
On/off Switch the appliance on or off.
Menu Open the operating mode menu
Information Display notifications Activate and deactivate the childproof lock
Childproof lock Activate and deactivate the childproof lock
Time-setting options Press briefly: Start or pause operation.
Press and hold for approx. threeseconds: Cancel operation.
Rapid heat-up Switch rapid heat-up on and off
Start/stop Start, pause or cancel the operation
4.3 Rotary selector
Use the rotary selector to change the setting values
that are shown in the display.
If you have reached the minimum or maximum value
for setting values, e.g. the temperature, this value re-
mains in the display. If required, use the rotary selector
to turn the value back again.
For lists, e.g. the types of heating, the first value starts
again after the last value.
4.4 Display
The display shows the current setting values.
The value that you can change in the display is high-
lighted in colour.
Status bar
The status bar is at the top of the display.
The time and set time functions are shown in the status
bar.
Progress line
The line is shown in the display below the highlighted
value.
The progress line shows you how much the appliance
has already heated up or how much time has elapsed.
The line is filled from left to right.
Countdown
You can view the countdown time or the cooking time
for the previous operation in the top right in the status
bar.

Operating modes en
7
If you have set a cooking time and the cooking time is
deleted, the countdown time takes over from the time
that has already elapsed from the cooking time. You
can therefore always check how long the operation has
already been running.
Temperature display
The heating-up control and the residual heat indicator
show you the temperature in the cooking compartment.
Due to thermal inertia, the temperature that is displayed
may differ slightly from the actual temperature inside
the cooking compartment. You can use the button
to check the current temperature.
¡Heating-up control
After the operation starts, the heating-up indicator
displays the rising temperature in the cooking com-
partment. When you are preheating the appliance,
the optimal time to place your food in the cooking
compartment is as soon as all the bars are filled.
For set levels, e.g. for grill settings, the heating-up
indicator is not displayed.
¡Residual heat indicator
When the appliance is switched off, the display
shows the residual heat in the cooking compart-
ment. The residual heat indicator goes out at ap-
prox. 60°C.
4.5 Cooking compartment
The functions in the cooking compartment make your
appliance easier to use.
Shelf supports
The rails in the cooking compartment enable you to
place accessories at different heights.
→"Accessories", Page9
Your appliance has five shelf positions. The shelf posi-
tions are numbered from bottom to top.
The rails are equipped with pull-out rails on one or
more levels, depending on the appliance type.
You can remove the rails, e.g. for cleaning.
→"Rails", Page23
Self-cleaning surfaces
The back panel in the cooking compartment is self-
cleaning. The self-cleaning surfaces are coated with a
porous, matte ceramic layer and have a coarse sur-
face. When the appliance is in operation, the self-clean-
ing surfaces absorb splashes from roasting or grilling
and break them down.
If the self-cleaning surfaces no longer clean themselves
adequately during operation, heat up the cooking com-
partment specifically to the right temperature.
→"Cleaning self-cleaning surfaces in the cooking com-
partment", Page19
Lighting
One or more oven lights illuminate the cooking com-
partment.
When you open the appliance door, the light in the
cooking compartment switches on. If the appliance
door remains open for longer than 15minutes, the light
switches off again.
For most operating modes, the lighting is switched on
during operation. The lighting switches off again when
the operation ends.
Cooling fan
The cooling fan switches on and off depending on the
appliance's temperature. The hot air escapes above
the door.
ATTENTION!
Do not cover the ventilation slot above the appliance
door. The appliance overheats.
▶Ensure that the ventilation slots are unobstructed.
To ensure that the appliance cools down more quickly
after operation, the cooling fan continues to run for a
certain period afterwards.
Appliance door
If you open the appliance door during operation, the
operation stops. When you close the appliance door,
the operation continues automatically.
5 Operating modes
This is where you can find an overview of your appli-
ance's operating modes and main functions.
Press to open the menu.
Operating
mode
Use
Types of
heating
Select finely tuned types of heating for
the optimal preparation of your food.
→"Types of heating", Page8

en Operating modes
8
Operating
mode
Use
Meals Use programmed, recommended set-
tings for various meals.
→"Dishes", Page13
Operating
mode
Use
Basic set-
tings
Adjust the basic settings. Basic settings
→Page17
HomeCon-
nect
Connect the oven to a mobile end
device and remotely control it.
→"HomeConnect ", Page15
5.1 Types of heating
To ensure that you always use the right type of heating
to cook your food, we explain the differences and ap-
plications below.
The symbols for each type of heating help you to re-
member them.
When you select a type of heating, the appliance sug-
gests a suitable temperature or setting. You can use
these values or change them within the specified
range.
For temperature settings above 275°C and grill set-
ting3, the appliance reduces the temperature to ap-
prox. 275°C or grill setting1 after approx. 40minutes.
Symbol Type of heating Temperature
range
What it's used for and how it works
Possible additional options
4Dhot air 30–275°C Bake and roast on one or more levels.
The fan distributes the heat from the ring-shaped heating element
in the back wall evenly around the cooking compartment.
Top/bottom heating 30–300°C Traditionally bake or roast on one level. This type of heating is
ideal for cakes with moist toppings.
The heat is emitted evenly from above and below.
Hot air eco 30–275°C Cook selected dishes gently on one level without preheating.
The fan distributes the heat from the ring-shaped heating element
in the back wall evenly around the cooking compartment. The
food is cooked in phases using residual heat.
This type of heating is most effective between 125 and 275°C.
Always keep the appliance door closed when cooking.
This type of heating is used to determine the energy consump-
tion in air recirculation mode and the energy efficiency class.
Top/bottom heating
eco
30–300°C Gently cook selected dishes.
Heat is emitted from above and below.
This heating function is most effective between 150 and 250°C.
This type of heating is used to measure the energy consumption
in the conventional mode.
Circulated air grilling 30–300°C Roast poultry, whole fish or larger pieces of meat.
The grill element and the fan switch on and off alternately. The
fan circulates the hot air around the food.
Grill, large area Grill settings:
1 = low
2 = medium
3 = high
Grill flat items such as steak and sausages, or make toast. Grat-
inate food.
The entire area below the grill element becomes hot.
Grill, small area Grill settings:
1 = low
2 = medium
3 = high
Grill small quantities, such as steak, sausages or toast. Gratinate
small quantities of food.
The central area below the grill element becomes hot.
Pizza setting 30–275°C Cook pizza or dishes that require a lot of heat from below.
The bottom heating element and the ring-shaped heating ele-
ment in the back wall heat the cooking compartment.
Slow cooking 70–120°C Slowly and gently cook seared, tender pieces of meat in un-
covered cookware.
The heat is emitted evenly from above and below at a low tem-
perature.
Bottom heating 30–250°C Final baking or cooking food in a bain marie.
Heat is emitted from below.
Keeping food warm 60–100°C Keep cooked food warm.

Accessories en
9
Symbol Type of heating Temperature
range
What it's used for and how it works
Possible additional options
Plate warming 30–70°C Plate warming.
CoolStart function 30–275°C For quickly preparing frozen products at position3. The temper-
ature depends on the manufacturer's instructions. Use the
highest temperature specified on the packaging.
The cooking time is as specified, or shorter.
Preheating is not useful.
6 Accessories
Use original accessories. These have been made espe-
cially for your appliance.
Note:Accessories may become deformed if they get
hot. Deformation has no effect on function. As the ac-
cessory cools down, it will regain its original shape.
The accessories supplied may differ depending on the
appliance model.
Accessories Use
Wire rack ¡Cake tins
¡Ovenproof dishes
¡Cookware
¡Meat, e.g. roasting joints or steak
¡Frozen meals
Universal pan ¡Moist cakes
¡Baked items
¡Bread
¡Large roasts
¡Frozen meals
¡Catch dripping liquids, e.g. fat when
grilling food on the wire rack.
Baking tray ¡Tray bakes
¡Small baked items
6.1 Locking function
The locking function prevents the accessories from tilt-
ing when they are pulled out.
You can pull out the accessories approximately halfway
without them tipping. The accessories must be inserted
into the cooking compartment correctly for the tilt pro-
tection to work properly.
6.2 Sliding accessories into the cooking
compartment
Always slide the accessory into the cooking compart-
ment the right way round. This is the only way to en-
sure that accessories can be pulled out approximately
halfway without tipping.
1. Turn the accessories so that the notch is at the
rear and is facing downwards.
2. Insert the accessory between the two guide rods for
a shelf position.
Wire rack Insert the wire rack with the open
side facing the appliance door and
the curved lip facing downwards.
Baking tray
E.g. univer-
sal pan or
baking tray
Slide the tray in with the sloping
edge towards the appliance door.
3. To place the accessory at shelf positions with pull-
out rails, pull out the pull-out rails.

en Before using for the first time
10
Wire rack
or baking
tray
Position the accessory so that its
edge is behind the lug on the pull-
out rail.
Note:The pull-out rails lock in place when they are
fully pulled out. Gently push the pull-out rails back
into the cooking compartment.
4. Push the accessory all the way in, making sure that
it does not touch the appliance door.
Note:Take any accessories that you will not be using
out of the cooking compartment while the appliance is
in operation.
Combining accessories
You can combine the wire rack with the universal pan
to catch any liquid that drips down.
1. Place the wire rack on the universal pan so that
both spacers are on the rear edge of the univer-
sal pan.
2. Insert the universal pan between the two guide rods
for a shelf position. In so doing, the wire rack is on
top of the upper guide rod.
Wire rack
on univer-
sal pan
6.3 Other accessories
You can purchase other accessories from our after-
sales service, specialist retailers or online.
You will find a comprehensive range of products for
your appliance in our brochures and online:
www.siemens-home.bsh-group.com
Accessories vary from one appliance to another. When
purchasing accessories, always quote the exact
product number (E no.) of your appliance.
You can find out which accessories are available for
your appliance in our online shop or from our after-
sales service.
7 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
7.1 Carrying out the initial configuration
When the appliance is connected to the electricity sup-
ply for the first time or following a lengthy power cut,
you must configure the settings before you can use it. It
may take a few seconds for the settings to appear on
the display.
Note:You can also enter the settings using the Home
Connect assistant. In this case, press to go to the
last point in the initial configuration. If your appliance is
connected, follow the instructions in the app.
Setting the language
1. Use the rotary selector to select the required lan-
guage.
2. Press ⁠.
aThe next setting appears.
Setting the time
1. Turn the rotary selector to set the current time.
2. Press ⁠.
aThe next setting appears.
Setting the date
1. Use the rotary selector to set the current day.
2. Press ⁠.
3. Use the rotary selector to set the current month.
4. Press ⁠.
5. Use the rotary selector to set the current year.
6. Press ⁠.
aA notification appears on the display confirming that
the initial configuration is complete.
7.2 Cleaning the appliance before using
it for the first time
Before using the appliance to cook food for the first
time, you must clean the cooking compartment and ac-
cessories.
1. Remove the product information and the accessor-
ies from the cooking compartment. Remove any
leftover packaging, such as polystyrene pellets, and
any adhesive tape either in or on the appliance.
2. Wipe the smooth surfaces in the cooking compart-
ment with a soft, damp cloth.
3. Press to switch the appliance on.
4. Apply the following settings:
Type of heating 4Dhot air
Temperature Maximum
Cooking time 1hour
→"Basic operation", Page11
5. Press to start the operation.
‒Ventilate the kitchen while the appliance is heat-
ing.
6. When the cooking time has elapsed, press to
switch the appliance off.
7. Once the appliance has cooled down, clean the
smooth surfaces in the cooking compartment with a
detergent solution and a dish cloth.

Basic operation en
11
8. Clean the accessories thoroughly using a detergent
solution and a dish cloth or soft brush.
8 Basic operation
8.1 Switching on the appliance
▶Press to switch the appliance on.
‒The button lights up blue.
aThe Siemens logo appears in the display. A type of
heating and a temperature are then displayed.
8.2 Switching off the appliance
Switch your appliance off when you are not using it.
The appliance will switch itself off automatically if it is
not used for a certain period of time.
▶Press to switch the appliance off.
‒The light above the button goes out.
aThe appliance switches off. Any functions currently
in progress are cancelled.
aThe time or residual heat indicator appears in the
display.
8.3 Starting operation
You must start each cooking operation.
▶Press to start the operation.
aThe settings, the run time and the heat-up line ap-
pear on the display.
8.4 Pausing or cancelling operation
You can briefly pause the operation and then continue.
If you cancel the operation completely, the settings are
reset.
1. To pause the operation briefly:
‒Briefly press ⁠.
‒To continue the operation, press ⁠.
2. To cancel the operation, press ⁠.
aThe operation stops and all of the settings are reset.
8.5 Setting an operating mode
Requirement:The appliance must be switched on.
1. Press ⁠.
The operating modes menu opens.
2. Press the operating mode that you require.
Various options are available depending on the op-
erating mode.
3. The selection can be changed using the rotary se-
lector.
Change any further settings depending on the selec-
tion.
4. Press to start.
8.6 Setting the type of heating and the
temperature
When you switch on the appliance, the types of heating
operating mode is set automatically.
1. Turn the rotary selector to select the required type
of heating.
2. Press the temperature.
3. Use the rotary selector to set the temperature.
4. Press to start the operation.
aThe appliance starts heating.
aThe set type of heating, temperature and cooking
time/appliance run time are shown in the display.
5. When the food is ready, press to switch the
appliance off.
Tip:The most suitable type of heating for your food
can be found in the type of heating description.
Note:You can also set a cooking time and an opera-
tion end time on the appliance.
→"Time-setting options", Page12
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1. Press to pause operation.
2. Press the type of heating.
3. Turn the rotary selector to select the required type
of heating.
aThe corresponding recommended temperature ap-
pears on the display.
Changing the temperature
Once the operation has started, you can change the
temperature directly.
▶Use the rotary selector to change the temperature.
aThe temperature is applied immediately.
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
▶Press ⁠.
aWhen available, information is displayed for a few
seconds.
9 Rapid heating
To save time, you can shorten the preheating time for
set temperatures of 100°C and higher.
You can use rapid heating for this type of heating:
¡4Dhot air
¡Top/bottom heating

en Time-setting options
12
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note:Do not set a cooking time until rapid heating has
come to an end.
1. Set a suitable type of heating and a temperature of
at least 100°C.
2. Press ⁠.
aThe symbol appears on the left of the display
next to the temperature.
aThe progress line begins to fill up.
3.
aWhen rapid heating has come to an end, a signal
tone sounds. The symbol disappears from the
display.
4. Place the food in the cooking compartment.
Cancelling rapid heating
▶Press ⁠.
aThe symbol disappears from the display.
10 Time-setting options
Your appliance has different time-setting options, with
which you can control its operation.
10.1 Overview of the time-setting
options
You can set a cooking time and an operation end time
on the appliance. The timer runs independently of the
appliance during the operation.
Time-setting
option
Use
Timer You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
Cooking time If you set a cooking time, the appli-
ance will stop heating automatically
once this time has elapsed.
End time Along with the cooking time (dura-
tion), you can set the time at which
you want cooking to end. The appli-
ance starts up automatically so that it
finishes cooking at the required time.
10.2 Setting the timer
The timer runs independently during the operation. The
timer can be set when the appliance is switched on or
off, up to 24 hours. The timer has its own audible sig-
nal so that you can tell whether it is the timer or a
cooking time that has elapsed.
1. Press ⁠.
aThe field for the timer opens.
2. Use the rotary selector to set the timer duration.
aThe timer starts automatically after a few seconds.
aThe symbol and the time counting down are dis-
played on the left in the status bar.
aThe timer counts down.
aWhen the timer duration has elapsed, a note ap-
pears on the display and an audible signal sounds.
3. Once the timer duration has elapsed:
‒Press to silence the audible signal manually.
‒To set another timer, press and use the rotary
selector to set the duration.
Changing the timer
You can change the timer duration at any time.
1. Press ⁠.
2. Use the rotary selector to change the timer duration.
3. Press to confirm.
Cancelling the timer
You can cancel the timer duration at any time.
1. Press ⁠.
2. Use the rotary selector to reset the timer duration to
zero.
3. Press to confirm.
10.3 Setting the cooking time
You can set a cooking time for operation of up to 23
hours 59 minutes.
Requirement:The type of heating and a temperature
or setting have been set.
1. Press ⁠.
aThe time-setting options menu opens.
2. Use the rotary selector to set the cooking time.
Rotation direction Default value
Left 10 minutes
Right 30 minutes
The cooking time can be set in one-minute incre-
ments up to one hour, and then in five-minute incre-
ments. The end time is calculated automatically.
3. Press to start the operation.
aThe appliance starts to heat and the time starts to
count down.
aOnce the cooking time has elapsed, an audible sig-
nal sounds. "Finished" appears in the status bar.
4. Once the cooking time has elapsed:
‒Press to silence the audible signal manually.
‒To set another cooking time, press and use
the rotary selector to set the cooking time.
‒To continue without setting a cooking time, press
⁠.
‒When the food is ready, press to switch the
appliance off.
Changing the cooking time
You can change the cooking time at any time.
1. Press ⁠.
2. Use the rotary selector to change the cooking time.
3. Then press twice.
Cancelling the cooking time
You can cancel the cooking operation time at any time.

Dishes en
13
1. Press ⁠.
2. Use the rotary selector to reset the cooking time to
zero.
3. ‒To continue without setting a cooking time, press
⁠.
The type of heating and temperature settings are
shown in the display.
10.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡In order to achieve good cooking results, do not
delay the end time once the appliance is operating.
¡Food will spoil if you leave it in the cooking com-
partment for too long.
Requirements
¡The type of heating and a temperature or setting
have been set.
¡A cooking time is set.
1. Press ⁠.
2. Press ⁠.
3. To set a later end time, turn the rotary selector.
4. Press to start the operation.
aThe status bar shows a notification when the opera-
tion starts. The appliance is in standby mode.
aOnce the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down in the status bar.
aOnce the cooking time has elapsed, an audible sig-
nal sounds. A notification appears in the status bar.
5. Once the cooking time has elapsed:
‒Press to silence the audible signal manually.
‒To set another cooking time, press and use
the rotary selector to set the cooking time.
‒To continue without setting a cooking time, press
⁠.
‒When the food is ready, press to switch the
appliance off.
Cancelling the end time
The set end time can only be changed when the oven
is in standby mode.
1. Press ⁠.
aThe time-setting options menu opens.
2. Press ⁠.
3. Use the rotary selector to reset the end time to zero.
aThe appliance starts to heat and the time starts to
count down.
Changing the end time
The set end time can only be changed when the oven
is in standby mode
1. Press ⁠.
aThe time-setting options menu opens.
2. Press " end".
3. Turn the rotary selector to change the end time.
4. Press to resume operation.
11 Dishes
The "Dishes" operating mode helps you to use your ap-
pliance to prepare different meals by selecting the op-
timum settings automatically.
11.1 Cookware
The cooking result depends on the composition of the
meat and the size of cookware.
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300°C. Glass or
glass ceramic cookware is best. The joint should cover
approx. two thirds of the cookware base.
Cookware made from the following material is not
suitable:
¡Bright, shiny aluminium
¡Unglazed clay
¡Plastic or plastic handles
11.2 Settings for the dishes
To make the dishes perfectly, the appliance uses differ-
ent settings.
Note:The cooking result depends on the quality and
composition of the food. Use fresh and, ideally, chilled
food. Use frozen food straight from the freezer.
Tips and information about the settings
If you set a dish, the display shows relevant information
for this dish, e.g.:
¡Suitable shelf position
¡Suitable accessory or cookware
¡Added liquid
¡Time for turning or stirring
When this time is reached, a signal sounds.
To call up the information, press "Tip" or . Some
notes are displayed automatically.
Programmes
The ideal type of heating, temperature and cooking
time are preset for programmes.
In order to obtain an optimal cooking result, you must
also set the weight. Unless otherwise indicated, set the
total weight for your dish. You can set the weight only
in the intended range.
Recommended settings
For the recommended settings, the optimum type of
heating is preset. The display shows the type of heat-
ing.
You can adjust the preset temperature and the cooking
time.
11.3 Overview of the dishes
You can find out which individual dishes are available
to you on the appliance when you call up the operating
mode.
The dishes are sorted by categories and food.

en Dishes
14
Category Foods
Cakes Cakes in tins
Cakes on a baking tray
Small baked items
Biscuits
Bread,
bread rolls
Bread
Bread rolls
Pizza, sa-
voury cakes
Pizza
Savoury cakes, quiche
Bakes,
soufflés
Bake, savoury, fresh, cooked ingredi-
ents
Fresh lasagne
Potato gratin, raw ingredients, flat
Bake, sweet, fresh
Soufflés in individual moulds
Frozen
products
Pizza
Bread rolls
Bakes
Potato products
Poultry, fish
Poultry Chicken
Duck, goose
Turkey
Meat Pork
Beef
Veal
Lamb
Game
Meat dishes
Fish. Fish
Vegetables Stew with vegetables
Browning vegetables
Baked potatoes, halved
Baked potatoes, whole
11.4 Adjusting the dish
Note:Once it has started, you can no longer change or
interrupt the dish or the settings.
Requirement:To start the operation, the cooking com-
partment must be cooled down.
1. Press ⁠.
2. In the operating modes menu, select "Dishes".
aThe first dish is suggested.
3. Use the rotary selector to select the required cat-
egory.
4. Press "Continue".
5. Use the rotary selector to select the required food.
6. Press "Continue".
7. Use the rotary selector to set the required dish.
8. Press "Continue".
9. Adjust the settings if required.
‒For some dishes, you can change the temperat-
ure, the cooking time or the end time by pressing
"Adjust".
‒For some dishes, you can set the weight directly
using the rotary selector.
10. For information about the accessory and shelf posi-
tion, press "Tip".
11. Press to start the operation.
aThe appliance starts to heat and the time starts to
count down. The heating line does not appear.
aOnce the dish is ready, a signal sounds. The appli-
ance stops heating.
12. Once the cooking time has elapsed:
‒Press to silence the audible signal manu-
ally.
‒For some dishes, you can extend the cooking
time if necessary.
→"Adding extra cooking time", Page14
‒When the dish is ready, press to switch the
appliance off.
Adding extra cooking time
For some dishes, the appliance allows you to extend
the cooking time once the set cooking time has
elapsed. You can do this as often as required.
1. If you do not want to extend the cooking time, press
"End" and then to switch the appliance off.
2. To extend the cooking time, press "Continue cook-
ing".
aA cooking time appears on the display.
3. If necessary, use the rotary selector to change the
cooking time.
4. Press to start the operation.
aThe appliance starts to heat and the time starts to
count down.
aOnce the cooking time has elapsed, an audible sig-
nal sounds. The appliance stops heating. The noti-
fication for extending the cooking time appears
again.
5. Once the cooking time has elapsed:
‒Press to silence the audible signal manu-
ally.
‒If you want to extend the cooking time again,
press "Continue cooking".
‒When the dish is ready, press "End" and use
to switch the appliance off.

Childproof lock en
15
12 Childproof lock
You can secure your appliance to prevent children
from accidentally switching it on or changing the set-
tings.
12.1 Activating and deactivating the
childproof lock
You can activate and deactivate the childproof lock re-
gardless of whether the appliance is switched on or off.
1. Press and hold for approx. fourseconds to ac-
tivate the childproof lock.
aA confirmation notification appears on the display.
aThe appears in the status bar when the appliance
is switched on or off.
2. Press and hold for approx. four seconds to de-
activate the childproof lock.
aA confirmation notification appears on the display.
13 Sabbath mode
You can set a cooking time of up to 74hours using
Sabbath mode. You can use top/bottom heating to
keep food warm between 85°C and 140°C during
this time without having to switch the appliance on or
off.
13.1 Starting Sabbath mode
Notes
¡If you open the appliance door during operation, the
appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again.
¡Once it has started, you can no longer change or in-
terrupt Sabbath mode.
Requirement:Sabbath mode is activated in the basic
settings.
→"Basic settings", Page17
1. Use the rotary selector to set the Sabbath mode
type of heating ⁠.
2. Press the temperature.
The temperature is preset to 85°C.
3. Use the rotary selector to set the desired temperat-
ure.
4. Press ⁠.
The time is preset to 25 hours.
5. Use the rotary selector to set the cooking time.
The end time cannot be delayed.
6. Press to start the operation.
aThe appliance starts to heat and the time starts to
count down.
7. Once the cooking time has elapsed, an audible sig-
nal sounds. A note appears on the display confirm-
ing that the operation has finished. The appliance
stops heating up and responds again as usual out-
side of Sabbath mode.
‒Press to switch the appliance off.
The appliance automatically switches off after ap-
prox.10to 20 minutes.
14 HomeConnect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the HomeConnect app, adjust its basic settings
and monitor its operating status.
The HomeConnect services are not available in every
country. The availability of the HomeConnect function
depends on the availability of HomeConnect services
in your country. You can find information about this at:
www.home-connect.com.
The HomeConnect app guides you through the entire
login process. Follow the instructions in the HomeCon-
nect app to configure the settings.
Tips
¡Please consult the documents supplied by
HomeConnect.
¡Please also follow the instructions in the HomeCon-
nect app.
Notes
¡Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the HomeCon-
nect app.
→"Safety", Page2
¡Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the HomeConnect
app.
¡In networked standby mode, the appliance requires
a maximum of2W.
14.1 Setting up HomeConnect
Requirements
¡The appliance is connected to the power supply and
is switched on.
¡You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smart-
phone.
¡The mobile device and the appliance are within
range of your home network's Wi-Fi signal.

en HomeConnect
16
1. Download the HomeConnect app.
2. Open the HomeConnect app and scan the follow-
ing QR code.
3. Follow the instructions in the HomeConnect app.
14.2 HomeConnect Settings
You can adjust the settings and network settings for HomeConnect by going to your appliance's basic settings.
Which settings the display shows will depend on whether HomeConnect has been set up and whether the appliance
is connected to your home network.
Basic setting Possible settings Explanation
Wi-Fi Switch on
Switch off
If Wi-Fi is activated, you can use HomeConnect.
In networked standby mode, the appliance requires a max-
imum of 2W.
Network Connect to network
Disconnect from network
If you disconnect the appliance from the network, all network
information will be deleted. This setting is useful if you have
new login details for the router.
Connect to app - This setting initiates the connection between the HomeCon-
nectapp and the appliance.
Remote control On
Off
When this function is deactivated, all you can do is view the
appliance's operating status in the app.
When this function is activated, you can remotely start and
control the appliance.
Appliance information - The display shows information about the network or the appli-
ance.
14.3 Operating the appliance with the
HomeConnect app
When the Remote start function is activated, you can
use the HomeConnectapp to remotely configure the
appliance's settings and start it.
Note:Some operating modes can only be started on
the oven itself.
Requirements
¡The appliance must be switched on.
¡The appliance must be connected to your home net-
work and to the HomeConnectapp.
¡To configure the appliance's settings using the
HomeConnectapp, "Remote control" must be
switched on in the basic settings. When the Remote
start function is deactivated, only the appliance's op-
erating statuses are displayed in the HomeCon-
nectapp.
1. Tap ⁠.
2. Tap "Remote start".
aThe display will show ⁠.
3. Configure a setting in the HomeConnectapp and
send it to the appliance.
Notes
¡If you open the appliance door within 15minutes
of activating the Remote start function or of the
set program ending, the Remote start function
will be deactivated.
¡When you start the oven using the controls on
the appliance itself, the Remote start function is
activated automatically. You can use the
HomeConnectapp to adjust the settings or start
a new program.
14.4 Software update
Your appliance's software can be updated using the
software update function, e.g. for the purposes of op-
timisation, troubleshooting or security updates.
To do this, you must be a registered HomeCon-
nectuser, have installed the app on your mobile device
and be connected to the HomeConnectserver.
As soon as a software update is available, you will be
informed via the HomeConnectapp and will be able to
start the software update via the app. Once the update
has been successfully downloaded, you can start in-
stalling it via the HomeConnectapp if you are in your
WLAN home network (Wi-Fi). The HomeConnectapp
will inform you once installation is successful.
Notes
¡You can continue to use your appliance as normal
while updates are downloading. Depending on your
personal settings in the app, software updates can
also be set to download automatically.
¡We recommend that you install security updates as
soon as possible.

Basic settings en
17
14.5 Remote diagnostics
Customer Service can use Remote Diagnostics to ac-
cess your appliance if you contact them, have your ap-
pliance connected to the HomeConnect server and if
Remote Diagnostics is available in the country in which
you are using the appliance.
Tip:For further information and details about the avail-
ability of Remote Diagnostics in your country, please
visit the service/support section of your local website:
www.home-connect.com
14.6 Data protection
Please see the information on data protection.
The first time your appliance is registered on a home
network connected to the Internet, your appliance will
transmit the following types of data to the
HomeConnect server (initial registration):
¡Unique appliance identification (consisting of appli-
ance codes as well as the MAC address of the Wi-Fi
communication module installed).
¡Security certificate of the Wi-Fi communication mod-
ule (to ensure a secure data connection).
¡The current software and hardware version of your
appliance.
¡Status of any previous reset to factory settings.
This initial registration prepares the HomeConnect
functions for use and is only required when you want to
use the HomeConnect functions for the first time.
Note:Please note that the HomeConnect functions
can only be utilised with the HomeConnect app. In-
formation on data protection can be retrieved in the
HomeConnect app.
15 Basic settings
You can configure the appliance to meet your needs.
15.1 Overview of the basic settings
Here you can find an overview of the basic settings
and factory settings. The basic settings depend on the
features of your appliance.
Basic setting Selection
Language See selection on the appli-
ance.
Clock Clock in 24-hour format.
Date – day Sets the current day
Date – month Sets the current month
Date – year Sets the current year
Signal tone Short cooking time
Medium cooking time1
Long cooking time
Button tone Switched on
Switched off1
Display brightness 5 settings
Clock display off
Digital + date1
Analogue
Lighting Off during operation
On during operation1
Childproof lock Keylock only 1
After switch-on Main menu
Types of heating1
Dishes
Night-time dimming Switched off1
Switched on
1Factory setting (may vary according to model)
Basic setting Selection
Brand logo Display1
Do not display
Fan run-on Recommended1
Minimum
Telescopic rails Retrofitted 1
Not retrofitted
Sabbath mode Switched on
Switched off1
Home Connect HomeConnect Settings
→"HomeConnect ",
Page15
Factory setting Reset
1Factory setting (may vary according to model)
15.2 Changing the basic settings
1. Press ⁠.
2. Press ⁠.
aThe operating modes menu opens.
3. Select the "Settings" operating mode.
aThe first basic setting appears.
4. Press to switch between the different settings.
5. Use the rotary selector to change the basic setting.
6. Press ⁠.
aThe display shows the changes "Save" or "Discard".
7. Press the required change.
Note:Your changes to the basic settings will be re-
tained even after a power failure.
Discarding changes to the basic settings
1. Press ⁠.
2. Press "Discard" .
aAll your changes are discarded and not saved.

en Cleaning and servicing
18
16 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
16.1 Cleaning products
In order to avoid damaging the various oven surfaces
on the appliance, do not use unsuitable cleaning
products.
WARNING‒Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶Do not use steam- or high-pressure cleaners to
clean the appliance.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶Do not use harsh or abrasive cleaning products.
▶Do not use cleaning products with a high alcohol
content.
▶Do not use hard scouring pads or cleaning
sponges.
▶Do not use any special cleaners for cleaning the ap-
pliance while it is hot.
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶Never use oven cleaner in the cooking compartment
when it is still warm.
▶Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
New sponge cloths contain residues from production.
▶Wash new sponge cloths thoroughly before use.
Suitable cleaning agents
Only use cleaning agents that are suitable for the differ-
ent surfaces on your appliance.
Follow the instructions on cleaning the appliance.
→"Cleaning the appliance", Page19
Appliance front
Surface Suitable cleaning agents Information
Stainless steel ¡Hot soapy water
¡Special stainless steel
cleaning products
suitable for hot sur-
faces
To prevent corrosion, remove any limescale, grease, starch or albu-
min (e.g. egg white) stains on stainless steel fronts immediately.
Apply a thin layer of the stainless steel cleaning product with a soft
cloth.
Plastic or painted
surfaces
E.g. control panel
¡Hot soapy water Do not use glass cleaner or a glass scraper.
To avoid permanent stains, remove any descaling agent that gets
onto the surface immediately.
Appliance door
Area Suitable cleaning agents Information
Door panels ¡Hot soapy water Do not use a glass scraper or a stainless steel wool.
Tip:Remove the door panels in order to clean them thoroughly.
→"Appliance door", Page20
Door cover ¡Made of stainless
steel:
Stainless steel cleaner
¡Made of plastic:
Hot soapy water
Do not use glass cleaner or a glass scraper.
Do not use stainless steel care products.
Tip:Remove the door cover for thorough cleaning.
→"Appliance door", Page20
Stainless steel in-
terior door frame
Stainless steel cleaner Discolouration can be removed using stainless steel cleaner.
Do not use stainless steel care products.
Door handle ¡Hot soapy water To avoid permanent stains, remove any descaling agent that gets
onto the surface immediately.
Door seal ¡Hot soapy water Do not remove or scrub.

Cleaning and servicing en
19
Cooking compartment
Area Suitable cleaning agents Information
Enamel surfaces ¡Hot soapy water
¡Vinegar water
¡Oven cleaner
Soak any heavily soiled areas and use a brush or steel wool.
Leave the appliance door open to dry the cooking compartment
after cleaning it.
Notes
¡Enamel burns at very high temperatures, causing minor discol-
ouration. The functionality of your appliance is not affected by
this.
¡The edges of thin trays cannot be completely enamelled and may
be rough. This does not impair corrosion protection.
¡Food residues will leave a white coating on the enamel surfaces.
The coating does not pose a health risk. The functionality of your
appliance is not affected by this. You can remove residues with
lemon juice.
Self-cleaning sur-
faces
- Follow the instructions for self-cleaning surfaces.
→"Cleaning self-cleaning surfaces in the cooking compartment",
Page19
Glass cover for
the oven light
¡Hot soapy water Use oven cleaner to remove very heavy soiling.
Rails ¡Hot soapy water Soak any heavily soiled areas and use a brush or steel wool.
Note:To clean thoroughly, detach the rails.
→"Rails", Page23
Pull-out system ¡Hot soapy water Use a brush to remove very heavy soiling.
Clean the pull-out rails while they are pushed in so that you do not
remove the lubricant.
Do not clean in the dishwasher.
Note:To clean thoroughly, detach the pull-out system.
→"Rails", Page23
Accessories ¡Hot soapy water
¡Oven cleaner
Soak any heavily soiled areas and use a brush or steel wool.
Enamelled accessories are dishwasher-safe.
16.2 Cleaning the appliance
In order to avoid damaging the appliance, you must
clean your appliance only as specified, and with suit-
able cleaning products.
WARNING‒Risk of burns!
The appliance and its parts that can be touched be-
come hot during use.
▶Caution should be exercised here in order to avoid
touching heating elements.
▶Young children under 8 years of age must be kept
away from the appliance.
WARNING‒Risk of fire!
Loose food remnants, fat and meat juices may catch
fire.
▶Before using the appliance, remove the worst of the
food residues and remnants from the cooking com-
partment, heating elements and accessories.
Requirement:Read the information on cleaning
products.
→"Cleaning products", Page18
1. Clean the appliance using hot soapy water and a
dish cloth.
‒For some surfaces, you can use alternative
cleaning agents.
→"Suitable cleaning agents", Page18
2. Dry with a soft cloth.
16.3 Cleaning self-cleaning surfaces in
the cooking compartment
The back panel in the cooking compartment is self-
cleaning. The self-cleaning surfaces are coated with a
porous, matte ceramic layer and have a coarse sur-
face. When the appliance is in operation, the self-clean-
ing surfaces absorb splashes from baking, roasting or
grilling and break them down. If the self-cleaning sur-
faces no longer clean themselves adequately during
operation, heat up the cooking compartment specific-
ally to the right temperature.
ATTENTION!
If you do not clean the self-cleaning surfaces regularly,
they may become damaged.
▶If dark stains are visible on the self-cleaning sur-
faces, heat up the cooking compartment.
▶Do not use oven cleaner or abrasive cleaning aids.
If oven cleaner accidentally comes into contact with
the self-cleaning surfaces, dab it off immediately us-
ing water and a sponge cloth. Do not rub.
1. Remove accessories and cookware from the cook-
ing compartment.
2. Detach the shelf supports and remove them from
the cooking compartment.
→"Rails", Page23
3. Remove coarse dirt using soapy water and a soft
cloth:
– From the smooth enamel surfaces
– From the inside of the appliance door

en Cleaning assistance
20
– From the glass cover on the oven light
This prevents stains that cannot be removed.
4. Remove any objects from the cooking compartment.
The cooking compartment must be empty.
5. Set the 4D hot air heating function.
6. Set the maximum temperature.
7. Start the operation.
8. Switch off the appliance after one hour.
9. Once the appliance has cooled down, wipe the
cooking compartment with a damp cloth.
Note:Marks may appear on the self-cleaning sur-
faces. Residues of sugar and egg white in the food
are not removed and stick to the surfaces. Red
stains are residues from salty food – they are not
rust. The stains are not hazardous to health. These
marks do not impair the cleaning ability of the self-
cleaning surfaces.
10. Attach the shelf supports.
→"Rails", Page23
17 Cleaning assistance
The cleaning assistance is a quick alternative for occa-
sionally cleaning the cooking compartment. The clean-
ing assistance softens dirt by vaporising the soapy wa-
ter. It is then easier to remove dirt.
17.1 Setting the cleaning aid
WARNING‒Risk of scalding!
If there is water in the cooking compartment when it is
hot, this may create hot steam.
▶Never pour water into the cooking compartment
when the cooking compartment is hot.
Requirement:The cooking compartment has cooled
down completely.
1. Remove the accessories from the cooking compart-
ment.
2. Mix 0.4litres water with a drop of washing-up liquid
and pour into the centre of the cooking compart-
ment floor.
Do not use distilled water.
3. Press ⁠.
aA type of heating and a temperature appears.
4. Use the rotary selector to set the bottom heat
type of heating.
5. Press the temperature.
6. Use the rotary selector to set the temperature to
80°C.
7. Press ⁠.
8. Use the rotary selector to set the time to
fourminutes.
9. Press to start.
aThe appliance starts to heat and the time starts to
count down.
aOnce the time has elapsed, an audible signal
sounds. A message appears in the status bar.
10. Use to switch the appliance off and leave the
cooking compartment to cool for approx.
20minutes.
17.2 Wiping down the cooking
compartment
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶After using the cleaning assistance, wipe the cook-
ing compartment and allow it to dry completely.
Requirement:The cooking compartment must have
cooled down.
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking compart-
ment with a dish cloth or a soft brush. Remove stub-
born food remnants using a stainless steel scouring
pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. In order to dry the cooking compartment, leave the
appliance door open in the detent position (approx.
30°) for approx.one hour.
18 Appliance door
To clean the appliance door thoroughly, you can disas-
semble the appliance door.
18.1 Detaching the appliance door
WARNING‒Risk of injury!
Components inside the appliance door may have sharp
edges.
▶Wear protective gloves.
The hinges on the appliance door move when the door
is opened and closed, which could trap your fingers.
▶Keep your hands away from the hinges.
1. Open the appliance door fully.