Siemon HD5 Series User manual

Note: All panel styles have either S110 or S310
style termination posts. All are designed for use
with a standard 110 type punch
-
down tool
HD5 & HD6 Series Wall & Rack Mount Patch Panel Instructions
Tools
1
Rack Mount Style Panels
Vertical Wall Mount Style Panels
Mount Panel
Mount S89D bracket with screws (not
included) suitable for mounting
surface being used.
Temporarily snap on vertical panel
with termination side out to allow for
easier cable termination.
Rack Mount Wall Mount
Route Cables (For ease of installation)
Route half of the
cables to each side of
panel.
Route cables such
that they feed into
center of connecting
blocks.
Using the #12
-
24 machine
screws and washers provided,
mount the panel to the desired
location on a 19” equipment
rack or equivalent.
Strip a minimum of 50mm (2 in.)
of cable jacketusing Siemon
AllPrep
TM
tool (p/n: CPT
-
RGTP)
or equivalent.
Prep cable
Lace conductors
S310 style
S110 style
Arrange pairs in accordance with the desired wire scheme as
detailed on the color coded sticker provided. Lace conductors
by pressing firmly into position from both sides of lacing post.
Tip: Begin lacing on side of panel where cables feed from to avoid
cable bundle interference.
Required Tools:
-
Jacket stripper
-
Phillips screw driver.
-
Cable cutters
-
110 punch tool
Optional Tools:
-
Multipair 110 punch
tool (for S110 style
terminations only).
19” Flat & Angled Rack Mount
Style Panels
Vertical Wall
Mount Style
Panels
2
3
4
See cross
-
referenceto outlet pin #’s on bottom of back page.

HD5 & HD6 Series Wall & Rack Mount Patch Panel Instructions
Global Headquarters
Watertown, Connecticut USA
Tel: (1) 866
-
548
-
5814
For a complete listing of our global offices visit our web site
www.siemon.com
© 2018 Siemon 12/18 100.11056 Rev.
i
Terminate conductors
Correct tool alignment
S310 style block
Incorrect tool alignment
(tool not perpendicular).
Terminate conductors using a Siemon S814 tool or equivalent
110 style single punch tool. Alternately a high impact multi
-
punch tool can be used with the S110 style blocks
S110 style block
REQUIRED for S310 Style
OPTIONAL for S110 Style
Snap on termination caps prior to
testing.
Note: Screwdriverslot provided
for removal of S310 style.
Attach rear cable manager
into slots provided on rear of
19” panel. Secure cables
with cable ties or hook & loop
managers.
Install manager & secure cables
Rack mount
Wall mount
Caution
: Do not over
-
tighten cable ties to
prevent deforming the cable jacket and potential
transmission performance degradation.
Install caps
Install labeling
Loosely secure /bundle cables
with cable ties or hook & loop
managers. Panel can now be
flipped back over with port
access facing out.
Peel paper backing from one of the adhesive
backed designation options
–
i.e. clear plastic
holder or icon/label holder (see note 1). Locate
bottom lip of holder to top edge of jacks and
press firmly.
Slide paper label strip into place and/or snap
optional colored icons into holder as desired.
Notes: 1). Both label options not available on some
panel styles. 2). Laser printable labels can be
ordered separately. Visit our web site or contact
Siemon Technical Services for our labeling software
template.
To ensure you have the latest revision to this document, pleasevisit:
http://www.siemon.com/us
5
6
7
8
To assist safe installations, comply with the following:
A. Use caution when installing or modifying telecommunications circuits.
B. Never touch uninsulatedwire terminals unlessthe circuit has been disconnected.
C. Never install this device in a wet location.
D. Never install wiring during a lightning storm.
Lors de l'installation, respectez les consignes de sécurité suivantes:
A. Utiliser avec prudence lors de l'installationou de la modification circuits de télécommunications.
B. Ne jamaistoucherles bornesde fil métallique non isolés sauf si le circuit a été débranché.
C. Ne jamais installer cet appareil dans un endroit humide.
D. Ne jamais installer pendant un orage.