Sigma ADA-26S User manual

ADA-26S
STEREO AUDIO
DISTRIBUTION AMPLIFIER
INSTRUCTION MANUAL
SIGMA ELECTRONICS, INC.
1027 COMMERCIAL AVENUE
EAST PETERSBURG, PA 17520-0448
[phone]
P.O. Box 448

ADA-26S STEREO AUDIO DISTRIBUTION AMPLIFIER
ADA-26S Doc. No. – 14480
Page 1 of 4
GENERAL:
The ADA-26S Stereo Audio Distribution Amplifier is designed to operate in two different modes. The first
mode provides three (3) dual-channel outputs from a stereo audio signal source. The other mode provides six
(6) single-channel outputs from a monaural audio signal source. The desired mode can be selected from the
front panel.
In either mode, the module is compatible with either balanced or unbalanced audio signals on the input
and outputs. Outputs can be mixed between balanced and unbalanced configuration dependent on the
requirement of the destination equipment.
POWER:
The ADA-26S operates from an AC power source of 120VAC or 230 VAC at line frequencies of 60 Hz or
50 Hz. The unit is supplied with an IEC 320 power inlet on the rear panel and a cordset with either a NEMA5-
15P or CEE7/7 plug.
Internally the unit has bus voltages of +15Vdc and -15Vdc supplied by regulators U01 and U02 respectively.
An LED on the circuit board illuminates the front panel when both supplies are operating properly.
Circuit protection is provided by the externally accessible fuse on the rear panel. Refer to the specification
section for proper fuse value.
FRAMES:
The ADA-26S module is mounted within a stand-alone box. The all-metal enclosure provides desirable
shielding to external EMI/RFI noise sources.
Rack-mounting requires the RMK-26 rack-mount kit. One RMK-26 rack-mount kit holds up to three of the 26
series units. Sigma provides various distribution amplifiers, signal generators and transcoding products in the
26 series.
CONNECTIONS:
Wiring to the module is performed via detachable screw terminal connectors (Figure 1).
INPUT: There are dual-channel inputs on the rear panel of the unit; the first and last connectors (Figure
2). The Right channel is on the left and the Left channel is on the right as seen from the rear of the unit. When
the unit is configured to provide six (6) outputs from a single input, the “Left Input” is disabled (the input on the
right).
Both inputs are a high impedance configuration. This allows the audio signals to be bridged to other units.
To ensure proper impedance matching it may be necessary to terminate the outputs with a 600Ωload. It is
recommended that, if termination is necessary, use a 600Ω, 1/2 watt resistor across the (+) and (-) outputs.
When multiple units have inputs bridged to the same source, only apply the 600Ωresistor to the last unit in the
line.
OUTPUT: There are three (3) outputs on the rear panel of the unit for each channel . Each output is
designed to drive a 600Ωload. Since each output on a channel is identical, the numbering is only provided for
the operator’s convenience. When the unit is configured to provide six (6) outputs from a single input, both
the right and left outputs will provide the same signal.
Figure 1
AUDIO CONNECTOR

ADA-26S STEREO AUDIO DISTRIBUTION AMPLIFIER
ADA-26S Doc. No. – 14480
Page 2 of 4
REAR PANEL CONNECTIONS
Figure 2
AUDIO CONFIGURATIONS:
The source and destination audio equipment must be evaluated to determine if they are Balanced or
Unbalanced. After determination is made, refer to the drawings provided to select the proper audio
configuration. The outputs can be any combination of balanced or unbalanced.
Balanced In to Balanced Out Balanced In to Unbalanced Out
Vout = Vin Vout = 0.5 Vin
Unbalanced In to Balanced Out Unbalanced In to Unbalanced Out
(-) Input Grounded; Vout = Vin Vout = 0.5 Vin
(-) Input Floating: Vout = 0.75 Vin
The input to output level comparison provided in the figures above, assumes the outputs are terminated
into a 600Ωload.
+
C
-
IN OUT
+
C
-
+
C
-
+
C
-
ADA-26S
+
C
-
IN OUT
+
C
-
+
C
-
+
C
Open
ADA-26S
+
Gnd
IN OUT
+
C
-
+
C
-
+
C
-
ADA-26S +
Gnd
IN OUT
+
C
-
+
C
-
+
C
Open
ADA-26S
1 2 33 2 1
-
C
+
FUSE
T125mA/T63mA
250V
120/240V~
60Hz/50Hz
12W
T
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
R I
I N
G P
H U
T T
-
C
+
-
C
+
-
C
+
-
C
+
-
C
+
-
C
+
-
C
+
L I
E N
F P
T U
T

ADA-26S STEREO AUDIO DISTRIBUTION AMPLIFIER
ADA-26S Doc. No. – 14480
Page 3 of 4
FRONT PANEL:
The adjustments and indicators on the front panel (Figure 3) can be accessed through the slots provided
in the ADA-26S frame. Factory settings of the module provide unity gain, maximum common mode rejection,
and a bandwidth of 100 kHz.
Gain Control - Gain control for the right channel is achieved by adjustments to S01and R012. Gain
control for the left channel is achieved by adjustments to S901and R912. S01 and S901 provide gain
adjustment in increments of 6dB, while R012 and R912 provide fine adjustments of +/- 3dB. The positions of
S01 and S901 make the following adjustments to the gain level of the circuit - = OFF, 1= -6dB, 2= 0dB, 3=
+6dB, 4= +12dB, 5= +18dBand 6= +24dB.
Mode Selection – To select the three (3) output stereo mode, set the mode select switch, S02, to the left
position. This will activate the Left gain controls and Left Input on the rear panel. To select the single input,
six (6) output mode, set the mode select switch, S02, to the right position. This will deactivate the Left gain
controls and input on the rear panel.
Figure 3: Front Panel Gain Adjustment
ADJUSTMENTS:
The ADA-26S has no adjustments other than the front panel gain control and mode selection.
SPECIFICATIONS:
INPUT: ...............................................Dual channel, Balanced, +24 dBm Maximum
INPUT IMPEDANCE: ........................30 kΩBalanced, DC coupled
OUTPUT: ...........................................+24 dBm Maximum
OUTPUT IMPEDANCE: ....................100ΩBalanced, DC coupled
LEFT/RIGHT SEPARATION: ............All outputs driven into 600Ω, unused input terminated.
............................................................Greater than 80 dB, 20 Hz to 20 KHz
HUM and NOISE: ..............................less than -80 dBm at Unity Gain, 22Hz to 22Khz filter
less than -65 dBm at +27 dB Gain, 22Hz to 22Khz filter
THD+N: .............................................Into 600Ω, 22Hz to 22Khz filter, 0dBm to +24 dBm
less than 0.05% 20 Hz to 20KHz)
IND (SMPTE 4:1 60Hz/7KhZ): ..........same conditions as THD+N, less than 0.02%
GAIN RANGE: ...................................(-6) to +24 dB in 6dB steps,±3dB vernier when terminated into 600Ω.
GAIN VARIATION: ............................±0.3 dB
CMR: .................................................Greater than 70 dB at 60 Hz, 60 dB at 20 KHz
0dBm to +24dBm
RESPONSE: ......................................Into 600Ω, ±0.2 dB, 20 Hz to30 KHz
S01
R012
S901
R912 S02
3
1 2 4 5
6
3
1 2 4 5
6

ADA-26S STEREO AUDIO DISTRIBUTION AMPLIFIER
ADA-26S Doc. No. – 14480
Page 4 of 4
TECHNICAL MANUAL:
A manual including schematics, circuit description, parts list and setup guide is available upon request. This
information is intended for the service of the module. Modules should be serviced by Qualified Personnel only
! Sigma Electronics, Inc. recommends service to be performed by our Factory Service Center.
NOTES:
All specifications, drawings, dimensions, weights and other details are subject to change without notification.
Information is intended to give a general performance and operation guideline of the product.
Sigma Electronics, Inc.; P.O.Box 448; 1027 Commercial Avenue; East Petersburg, PA 17520-0448
Main Office: Tel: [phone] Fax: [phone]
REV2 OCT01 ADA-26S