SIIG Cyber 1S1P PCIe User manual

1
Cyber 1S1P PCIe
Quick Installation Guide
04-0615B
Introduction
TheCyber1S1PPCIehigh-speedserialI/Ocardprovides
one 9-pin RS-232 serial port and one parallel port.
FeaturesandBenefits
•PCI Express 1-lane (x1) adapter that works in any
PCI Express slot
•Compliant with PCI Express Base Specification
Revision 1.0a
•Provides an RS-232 serial & parallel port (DB-25)
•Parallel port supports ECP, EPP, SPP (standard)
parallel port modes
SystemRequirements
•PCI Express-enabled system with an available PCI
Express slot
•Windows® 8 (32-/64-bit) / 7 (32-/64-bit) / Vista
(32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008
(32-/64-bit) / Server 2008 R2 / 2000
PackageContents
•Cyber 1S1P PCIe adapter
• DriverCD
• Quick installation guide

2
Layout
Hardware Installation
General instructions for installing the card are provided
below. Since the design of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the computer.
3. Remove your computer’s cover, then remove the
slot bracket cover from an available PCI Express
slot.
4. To install the card, carefully align the card's bus
connector with the selected PCI Express slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
Figure 1: Layout
Serial Port
Parallel Port

3
5. Replace the slot bracket screw to secure the card.
6. Replacethecomputercoverandreconnectthepower
cord.
Driver Installation
Install the board and boot up Windows, then follow the
instructions below to install the Cyber 1S1P PCIe drivers.
Windows 8 (32-/64-bit) / 7 (32-/64-bit) / Server
2008R2
Note: Windows 7 may automatically search
preconfigured driver folders for the proper driver.
This process may take several minutes to complete.
Do not interrupt this process.
1. ForWindows8andWindows7:RightclickComputer,
click Manage, click Device Manager.
For Server 2008 R2: Right click Computer, click
Manage. Double click Diagnostics, click Device
Manager.
2. Insert the driver CD. Close the CD AutoPlay box if
prompted.
3. RightclickPCIDeviceorPCIParallelDeviceunder
other devices, click Update Driver Software.
4. Click Browse my computer for driver software.
5. TypeD:, thenclick Next. (Change D:to match your
CD/DVD-ROM drive letter)
6. AtWindowshassuccessfully updatedyourdriver
software, click Close.
7. Go back to Device Manager, right click PCI Device
or PCI Serial Device under other devices, click
UpdateDriver Software.

4
8. Repeat steps 4-6, then restart the computer to
complete the installation.
WindowsVista(32-/64-bit)/Server2008(32-/64-
bit)
1. At the Found New Hardware, click Cancel.
2. InsertthedriverCD.ClosetheCDAutoPlaywindow
if prompted.
3. For Windows Vista: Right click Computer, click
Manage,clickContinue,thenclickDeviceManager.
ForWindowsServer2008:RightclickComputer,click
Manage.DoubleclickDiagnostics,thenclickDevice
Manager.
4. RightclickPCIDeviceorPCIParallelDeviceunder
Other devices, then click Update Driver Software.
5. Click Browse my computer for driver software,
then click Let me pick from a list of device drivers
on my computer.
6. Click Ports (COM & LPT), click Next, then click
Have Disk.
7. For 32-bit: Type D:\XP-Later\32-bit, click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
For 64-bit: Type D:\XP-Later\64-bit, click OK.
(Change D: to match your CD/DVD-ROM drive
letter)
8. Click Next, then click Close.
9. Go back to Device Manager, right click PCI Device
or PCI Serial Device under Other devices, then
click Update Driver Software.
10. Repeat steps 4-8, then click Yes to restart the
computer.

5
WindowsXP/Server2003(32-/64-bit)
1. InsertthedriverCD. ClosetheCDAutoPlaywindow
if prompted.
2. AttheFoundNewHardwareWizard,selectInstall
from a list or specific location (Advanced),then
click Next.
3. Check Include this location in the search, uncheck
the other boxes.
For32-bit:TypeD:\XP-Later\32-bit,andclickNext,
then click Finish. (Change D: to match your CD/
DVD-ROM drive letter)
For64-bit:TypeD:\XP-Later\64-bit,andclickNext,
then click Finish. (Change D: to match your CD/
DVD-ROM drive letter)
4. Repeat steps 2-3, then restart Windows to complete
the installation.
Windows2000
1. Insert the driver CD.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended), then click Next.
4. Check Specify a location, uncheck the other boxes,
then click Next.
5. Type in D:\2K, then click OK. (Change D:to match
your CD/DVD-ROM drive letter)
6. Click Next and Finish.
7. Repeat steps 2-6, then restart Windows to complete
the installation.
ToVerifyWindowsInstallation
1. Check in Device Manager to verify installation.

6
ForWindows8/7/XP/Server2003/ 2000:Rightclick
Computer or My Computer, click Manage, click
Device Manager.
For Windows Vista: Right click Computer, click
Manage, click Continue, click Device Manager.
For Windows Server 2008 / Server 2008 R2: Right click
Computer,clickManage,doubleclickDiagnostics,
click Device Manager.
2. Double click Ports (COM & LPT), CyberSerial
16C950...andSIIGCyberProParallelPort...should
be displayed.
Changing COM / LPT Port Number
Some serial or parallel devices need a specific port in
order to work. If your device works properly, do not
change this setting.
To change COM port:
1. FromtheDeviceManager,doubleclickPorts(COM
&LPT),thendoubleclicktheCyberSerial16C950...
2. Click Settings tab.
3. ClickthedownarrownexttotheCOMPortnumber,
select a COM port that is not in use, then click OK.
4. Click OK, then close Device Manager to save the
change.
To change LPT port:
1. FromtheDeviceManager,doubleclickPorts(COM
&LPT),thendoubleclicktheSIIGCyberProParallel
Port.
2. Click Settings tab.
3. Click thedown arrownextto the LPTPortnumber,
select a LTP port that is not in use, then click OK.
4. Click OK, then close Device Manager.

7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web
site at www.siig.com and click Support. Our online support database is
updated daily with new drivers and solutions. Answers to your questions
could be just a few clicks away. You can also submit questions online and
a technical support analyst will promptly respond.
SIIG offers a lifetime manufacturer warranty with this product. This
warranty covers the original purchaser and guarantees the product to be
free of any defects in materials or workmanship for the life of the product.
SIIG will, at our discretion, repair or replace (with an identical product or
product having similar features and functionality) the product if defective
inmaterials orworkmanship. This warrantygives youspecific legal rights,
and you may also have other rights which vary from state to state. Please
see our web site for more warranty details.
Ifyouencounteranyproblemswiththisproduct,pleasefollowtheprocedures
below.
A) If it is within the store's return policy period, please return the product
to the store where you purchased it.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,pleasefollow
these steps to have the product repaired or replaced.
Step1: Submit your RMA request. Go to www.siig.com, click Support,
then RequestAProduct Replacementto submit a request to SIIG RMA
or fax a request to 510-657-5962. Your RMA request will be processed,
if the product is determined to be defective, an RMA number will be
issued.
Step 2: After obtaining an RMA number, ship the product.
•Properlypacktheproductforshipping. Allsoftware,cable(s)andany
other accessories that came with the original package must be
included.
•Clearly write your RMA number on the top of the returned package.
SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted
on the outside of the shipping carton.
•Youareresponsibleforthecost of shippingtoSIIG. Shiptheproduct
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIGwillshiptherepairedorreplacedproductviaGroundintheU.S.
and International Economy outside of the U.S. at no cost to the
customer.

About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions(includingSerialATAandUltraATAControllers,FireWire,USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebook systems and external peripherals. SIIG continues to grow by
adding A/V and Digital Signage connectivity solutions to our extensive
portfolio. AllcenteredaroundthedistributionandswitchingofA/Vsignals
overCAT5/6,theseproductsincludematrixswitches,distributionamplifiers,
extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to
providinghighqualityproductswhilekeepingeconomicalandcompetitive
prices. High-quality control standards are evident by one of the lowest
defective return rates in the industry. Our products offer comprehensive
user manuals, user-friendly features, and most products are backed by a
lifetime warranty.
SIIG products can be found in many computer retail stores, mail order
catalogs, and e-commerce sites in the Americas, as well as through major
distributors, system integrators, and VARs.
PRODUCT NAME
Cyber 1S1P PCIe
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
Cyber1S1PPCIeisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarksofSIIG,
Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names
usedinthispublicationareforidentificationonlyandmaybetrademarksoftheirrespectiveowners.
April, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.