Silicon Solar AQUAJET-MAXFLOW-50 User manual

1. Overview
• The waterfall pump kit is designed for solar powered waterfalls or
helping circulate water for your Koi/ Fish farms. It is powered by DC
power supply through the solar module. There are also battery sto-
ring options, if you are interested in powering your waterfall pump
kit after the sun goes down
• Using Solar power the performace of the waterfall pump kit de-
pends on its orientation and the intensity of sunlight. To ensure
maximum solar energy exploitation the solar cells need to face the
sun as much as possible
• Each kit includes outdoor rated wire for direct burial. Connectors are
watertight plug and play connectors, no complicated wiring needed.
SOLAR WATERFALL PUMP KIT USER‘S MANUAL
Aqua Jet Pro
SKU: AQUAJET-MAXFLOW-50
Read And Follow All Instrucons Before Operang Your Solar Waterfall Pump Kit.
Save This Manual For Future Reference.
Copyright 1997 - 2015 Silicon Solar | All Rights Reserved |
Version 1.0.0
* Prices and specicaons subject to change without noce
Silicon Solar
2917 State Hwy 7
Bainbridge, MY 13733
P: 1.800.786.0329
www.SiliconSolar.com
2. Components
• For high ecency and long service life, the latest DC brushless motor technology is introduced in the pump design and
manufacturing
• The pump includes our proprietary dry-run protection. The dry-run protection is provided by two sensorpoints on one
side of the pump body. Make sure both of the points are submerged in water. If either or both points emerge out of wa-
ter, the pump stops working.

4. Cautions
1. Any altering of the product itself or changing the components voids warranty.
2. Do not connect the pump to any AC voltage power directly, it is ONLY for DC power voltage.
3. Operate the pump in water only (never above 40° C/ 104°F), keep it away from ammable liquids.
4. The pump is dry-run protected. It will automaticly stop working, if there is not enough water.
5. Do not strike the solar panel.
7. Technical data
Operating voltage DC 12V
Dimensions 30x30x55 in
Weight 80 lbs
Maximum Flow Rate 1500 GPH
Pump lift 10 feet of head
6. Functionality problems
If the Solar waterfall pump kit does not operate, please check the following possible reasons:
1. No connection to the power supply. Make sure all mc connectors are plugged in well and the solar panel is facing the sun.
2. The pump is not fully submerged in water.
3. Impeller of the pump is blocked - to clean the pump as described in Cleaning and maintenance of the pump.
4. No water running through the tubes. Clear the tube and the lter to make sure the tube is through completely.
Copyright 1997 - 2015 Silicon Solar | All Rights Reserved | Version 1.0.0
* Prices and specicaons subject to change without noce
Silicon Solar
2917 State Hwy 7
Bainbridge, MY 13733
P: 1.800.786.0329
www.SiliconSolar.com
5. Cleaning and Maintenance of the pump
If the pump starts losing power or stops working after a certain time, please clean up the sediment inside the pump or the
debris on the lter cribs. The pump can be opened by unscrewing the four screws on the four corners of the lter housing
bottom. To clean the pump, disassemble the pump according to the below gure before cleaning all the parts with water.
3. Assembling
1. Unpack all components carefully.
2. For the application of pumping water for a waterfall, install the submersible pump at the lowest basin of your waterfall.
3. Carefully install plastic tubing.
4. Electrically connect the solar panel to the pump by plugging the four MC4 connectors in, two of them on the panel and
the other two on the pump.
5. Install the solar panel on a at roof, ground or pole as you selected in the mounting options. The performance of the
waterfall pump kit depends on its orientation and the intensity of sunlight. To ensure maximum solar energy exploitation
the solar cells need to face the sun as much as possible.
6. The solar pump is now ready to operate.