Silver King SKRS28-RSUS10 Quick start guide


















Specifications Subject to Change Without Notice.
Technical Manual
and
Replacement Parts List
MODELS: SKRS28-RSUS10
SKRS28-RSUS11
SKRS28-RSEU10
SKRS28-RSEU11
SKRS28-RSEU12
SKRS28-RSUK10
Shelf Refrigerator
FORM NO. 45491 REV A 11/2019
1600 Xenium Lane North, Minneapolis, MN 55441-3787
Phone [phone]

1


TECHNICAL MANUAL
SILVER KING MODEL SKRS28-RS
Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most reliable equipment
in the industry today. Please read this manual and the accompanying warranty information before operating your new Silver King unit.
INSPECT FOR DAMAGE AND UNCRATE
Upon delivery of your new Silver King unit, uncrate at once to inspect for possible damage following the instructions printed on the
exterior of the container. Report any damages to the carrier responsible for transportation and promptly present a claim for any
evidence of mishandling. Save all packaging materials if a claim is filed.
PRECAUTIONS BEFORE USING THIS PRODUCT
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Use caution when cleaning the condenser, the fins are very sharp.
For units with a dual hertz rating, no adjustments are required for normal operation.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
This refrigeration unit is not intended to be used at altitudes higher than 2000 meters.
Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
Do not exceed the maximum load capacity of 50 pounds per shelf.
Use caution when moving, installing, maintaining and using this refrigeration device to avoid either damaging the
refrigerant tubing or increasing the risk of a leak.
All component parts must be replaced with like components and all servicing must be done by factory authorized service
personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper service.
If the unit has recently been transported on its side (or placed horizontally), then please let unit stand with the casters (or
feet) on the ground for a minimum of 24 hours before plugging it in.
WARNING: This product can expose you to chemicals including lead, which are known to the State of
California to cause cancer, birth defects, or other reproductive harm.

2
INSTALLATION
The stainless steel exterior of the cabinet has been protected by a plastic covering during manufacturing and shipping. This covering can
be readily stripped before installation. After removing this covering, wash the interior and exterior surfaces using a warm, mild soapy water
solution and a sponge or cloth, rinse with clean water and wipe dry.
Shelf
Inside the unit you will find a Shelf and a plastic bag containing Shelf Supports. The Shelf Supports with the “tang” go on the rear Pilasters.
This shelf system allows for easy adjustment to suit your needs.
Door Adjustment
Should the Door ever require straightening, loosen the Screws on the Hinges, square the Door with the cabinet and retighten the Screws.
Door Swing
To reverse the door swing, unscrew the top hinge pin and lift the door off. Remove the top and bottom hinge screws and slide the hinges
out. Remove the hinge screws on the opposite side of the cabinet. Using a stiff putty knife, pry out the gray plastic hinge plugs and install
on the oppsite side of the cabinet and re-install the hinge screws. Insert the hinges in the hinge holes flipping the top hinge. Re-install the
door and top hinge pin and adjust the door for proper seal.
Location
When locating your new refrigerator, convenience and accessibility are important considerations, but the following installation guidelines
must be followed;
Always avoid placing the refrigerator adjacent to an oven, heating element or hot air source that would affect the operation of the
unit.
For proper ventilation the unit requires the following minimum clearances:
o3 inches on the sides, back and above the cabinet. Install the rear air baffle per the instructions included.
The unit must be level or tilted backwards slightly.
When placing the unit on a counter or shelf the structure must be able to support a minimum of 200 pounds.
The unit is designed to be sealed to the supporting structure surface with a waterproof sealant as required by NSF International.
To do so, locate the unit in its desired location (following the instructions), apply a bead of sealant around the perimeter and smooth
out with a finger to form a radius with the surface and the unit.
Energy Rating
Your Silver King refrigerator has a class 4 energy rating. The refrigerator was tested at an ambient temperature of 40°C at 40% relative
humidity.


3


Electrical Connections
Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to power. The
specifications on the data plate supersede any future discussion.
The standard refrigerator is equipped with an eight (8) foot power cord that requires a 115 Volt, 60 Cycle, 1 Phase properly
grounded electrical receptacle. The power cord comes with a 3 prong plug for grounding purposes. Any attempt to cut off the
grounding spike or to connect to an ungrounded adapter plug will void the warranty, terminate the manufacturer’s responsibility and
could result in serious injury. The circuit must be protected with a 15 or 20 ampere fuse or breaker. The unit must be isolated on a
circuit and not plugged into an extension cord.
OPERATION
Initial start up
After satisfying the installation requirements, the refrigerator is ready to start. The refrigerator will start when the power cord is
connected to the required power source. If the compressor does not start when the unit is initially plugged in, check to make sure
that the Temperature Control is not in the “off” position. Allow the unit to run for two hours before loading it with product. When
loading the unit with product, take care not to block the air flow at the back of the storage area as this would affect the unit’s
performance.
Temperature Control
The Temperature Control is located on the back panel of the cabinet and is factory set to maintain an average cabinet temperature of
approximately 38 degrees F (3 Degrees Celsius). To obtain colder temperatures, press and hold the set button until the set point
value flashes. Use the up or down arrow buttons to change the value and then press the set button again. Allow the unit a minimum
of one hour to respond to a control setting adjustment.
Defrost
Your Silver King refrigerator is an automatic defrost unit and no additional plumbing is required. Automatic defrosting is
accomplished when frost buildup on the evaporator coil is cleared during compressor “off” cycles. Defrost water is collected in a pan
located in the compressor compartment where it is evaporated into the room air. It is important that the unit be installed level to
allow proper drainage of the condensate water.
MAINTENANCE
Preventative maintenance is minimal although these few steps are very important to continued operation and maximizing the life of
the appliance.
Cabinet Surfaces
The cabinet interior is aluminum and the exterior is stainless steel. These surfaces should be cleaned periodically with a solution of
warm water and mild soap, rinsed and wiped dry with a soft cloth. A stainless steel cleaner can also be used. Should a surface
become stained or discolored, do not attempt to clean with an abrasive cleanser or scouring pad. Use a soft cleanser and rub with
the grain of the metal to avoid scratching the surface. Do not use chlorinated cleaners. Always rinse well and dry after cleaning.
Condenser
Periodically, dust on the condenser coil and filter screen must be cleaned. The filter screen can be removed from the right rear of
the cabinet. The condenser is located on the back of the unit. Clean the accumulated dust/debris with a vacuum or brush or
chemical cleaning agent (Nu-Calgon 4171-75 or equivalent). This will need to be done regularly to maintain the compressor
warranty!
WARNING: The condenser fins are very sharp, use caution when cleaning the condenser.
Door Gasket
The Door Gasket will collect dirt and should be wiped clean with a warm, mild soapy water solution to extend its life and assure
maximum cabinet performance and life.
MODEL SERIAL NO. DATE INSTALLED

4



5
ITEM NO. PART DESCRIPTION PART NO.
1 PILASTER SHELF 42984
2 SHELF SUPPORT 99530
3 SHELF SUPPORT W/ TANG 99531
4 SHELF 42552
5 DOOR ASSEMBLY COMPLETE 38997
6 DOOR GASKET KIT 10310-81
7 HINGE TOP 27181
8 PIN HINGE 22415
9 HINGE B OTTOM 38988
10 DOOR BUSHING 99711
11 BAFFLE 39366
12 BACK PANEL 39009
13 EVAPORATOR 62553
14 CAPILLARY TUBE 21209-4
15 PROBE TEMPERATURE 38822
16 CONDENSER COIL 61498
17 CONDENSATE PAN ASSEMBLY 35412
FAN MOTOR CONDENSER 115V 37736
FAN MOTOR CONDENSER 230V 37814
COMPRESSOR 115V (WITH DRIER AND ELECTRICALS) 10343-86
COMPRESSOR 230V-50/60HZ (WITH DRIER AND ELECTRICALS) 10343-87
ELECTRICAL KIT COMPRESSOR (RELAY,OVERLOAD) 115V 10344-86
ELECTRICAL KIT COMPRESSOR (RELAY,OVERLOAD) 230V 10344-87
21 DRIER 22677
22 GROMMET 20481
23 WASHER 22401
24 HAIRPIN CLIP 98106
POWER CORD 115V 32199
POWER CORD 230V EURO 43998
POWER CORD 230V UK 43999
POWER CORD 230V EN60309 37553
26 THERMOMETER 22409
TEMPERATURE CONTROL 115V 37587
TEMPERATURE CONTROL 230V 37817
FAN MOTOR EVAPORATOR 115V 37736
FAN MOTOR EVAPORATOR 230V 37814
29 FAN GUARD EVAPORATOR 35253
30 BUMPER BOTTOM 39399
FORM 45490
20
19
25
27
18
28
LIST REPLACEMENT PARTS - SKRS28-RS






































 
WHEN ORDERING REPLACEMENT PARTS, PLEASE PROVIDE MODEL AND SERIAL NUMBERS.

6






















7
Thermistor Field Testing
Thermistor Part Number 38822. See form M164 for the standard operating procedure.
Establish Thermistor Temperature
Check the display’s temperature reading.
If a thermometer is available, use it to confirm the display’s
temperature reading by taking the temperature at the thermistor.
If the previously stated tasks are unavailable, then use any
reasonable means to estimate the thermistors temperature.
Multimeter Set-up
Use a multimeter and set it to the resistance (Ω) setting. See
Figure 1.
Disconnect the thermistor from the controller, then connect the
multimeter to the thermistor. See Figure 1.
Check and compare the multimeter’s reading to Table 1.
Analyze Results
If the resistance and temperature are similar, then the thermistor
is working properly and does not need to be replaced.
If the resistance and temperature are not similar or the
resistance’s value is not on Table 1, then the thermistor is not
working properly and needs to be replaced.
If the resistance reads over-limit, then the thermistor is not
working properly and needs to be replaced.
Temp
(°F)
Ohms
(kΩ)
Temp
(°C)
-22.0 114.56 -30
-18.4 103.18 -28
-14.8 93.07 -26
-11.2 84.06 -24
-7.6 76.03 -22
-4.0 68.87 -20
-0.4 62.46 -18
3.2 56.71 -16
6.8 51.56 -14
10.4 46.94 -12
14.0 42.78 -10
17.6 39.04 -8
21.2 35.66 -6
24.8 32.62 -4
28.4 29.86 -2
32.0 27.37 0
35.6 25.11 2
39.2 23.06 4
42.8 21.20 6
46.4 19.51 8
50.0 17.98 10
53.6 16.58 12
57.2 15.3 14
60.8 14.13 16
64.4 13.07 18
68.0 12.09 20
71.6 11.2 22
75.2 10.38 24
78.8 9.63 26
82.4 8.95 28
86.0 8.31 30
89.6 7.73 32
93.2 7.2 34
Table 1
Figure 1
P/N 45810 - Rev A - By AV - 7/3/19

8
SILVERKINGWARRANTY–LEGACYPRODUCTLINE
SilverKingwarrantstotheoriginalpurchaserofeverynewSilverKingLegacyrefrigeratedself‐contained
unit(asdefinedbelow),thattheEquipmentshallbefreefromdefectsinmaterialandworkmanshipunder
normaluseandserviceasoutlinedintheTechnicalManualforaperiodofone(1)yearfromthelaterof
either(a)thedateofshipmentfromthemanufactureror(b)thedateofinstallation(the“Warranty
Period”),butinnoeventshalltheWarrantyPeriodcommencelaterthansix(6)monthsfromthedateof
shipmentfromthemanufacturerunlessotherwiseagreeduponbythepartiesinwriting.Equipment
includesGeneralMarketRefrigerationunitsandexcludesallDispensingandCustomHoldingRefrigeration
orextendedagreementswhosewrittentermsareconditionalattimeofsaleorcontract.Allwarrantiesare
subjecttospecificlimitationsoutlinedbelow.

ThisEquipmentwarrantydoesnotapplyto:Repairorreplacementrequiredasaresultofcarelessnessor
neglect.Improperinstallation,incorrectvoltagesupply,modifying,tamperingwithoralteringcomponents
and/orEquipment.Failuretoperformpropermaintenance.Thiswarrantydoesnotapplytodamage
resultingfromfire,water,burglary,accident,abuse,misuse,transit,actsofGod,terrorism,attempted
repairs,improperinstallationormaintenancebyunauthorizedpersons,anddoesnotapplytofoodloss.
Unitiscompromisedbyaddingexcessweightoradheringnonapprovedcomponentstotheframe.
Combiningtheequipmentwithhardware,fixtures,accessoriesorotherequipmentnotprovidedbySilver
King.MisuseoftheEquipmentoruseoftheEquipmentnotinaccordancewiththeTechnicalManual.
Warrantyexcludesconsumablesorreplacementcomponentssuchasshelving,trays,gaskets,etc.Warranty
excludesinteriorlinerorexteriorshell.Condensingcoilsmustbecleanedatregularintervals.Failuretodo
socancausecompressormalfunctionandwillvoidwarranty.Althoughcleaningrequirementsvaryin
accordancewithoperationofvariousproducts,SilverKingadvocatesaminimummonthlycleaning.
TheEquipmentwarrantydoesnotincludefreight,handling,installation,labor(followingthe(1)yearlabor
warrantyperiod)orotherincidentalorconsequentialcostsincludingproductand/oreconomicloss.This
Equipmentwarrantyisinlieuofallotherwarranties,expressorimplied,areherebydisclaimedand
excludedincludingthoseofmerchantability,andfitnessforaparticularpurpose.ThisEquipmentwarranty
isnon‐transferable.SpecificprovisionsofthisEquipmentwarrantyareasfollows:

90DAYREPLACEMENTPARTSWARRANTYSilverKingwarrantstotheoriginalEquipmentpurchaserthata
replacementOEMpartthereofwillbefreeofdefectsinmaterialandworkmanship,undernormaluseand
service,foraperiodof90daysfromthedateoforiginalpurchaseofsuchreplacementOEMpartsubjectto
alltermsandconditionsherein.

LIFETIMEHINGEANDHANDLEWARRANTYSilverKingprovidesalifetimewarrantyonhingesandprimary
(doorordrawer)handles.Intheeventofanon‐conforminghingeorprimaryhandle,SilverKingshall
provideareplacementpart;however,Purchasershallberesponsibleforanyotherreplacementcosts,
includingbutnotlimitedtoshipping,installationandlabor.

Three(3)YearDrawerSlideWarrantySilverKingwarrantstotheoriginalEquipmentpurchaserforaperiod
oftimenottoexceedtheearlierofthefollowing:three(3)yearsfromthedateoforiginalpurchaseofthe
Equipmentorthree(3)yearsandsix(6)monthsfromthedateofshipmentfromthefactoryofthe
equipment,thatitwillreplacethedrawerslideswithoneofsimilardesignandcapacity,exclusiveof
deliveryandinstallationcharges,ifitisfoundinSilverKing’sreviewtobeinefficientorinoperativedueto
defectsinmaterialorfactoryworkmanship.



9


FIVE(5)YEARCOMPRESSORWARRANTYSilverKingwarrantstotheoriginalEquipmentpurchaserfora
periodoftimenottoexceedthefollowing:five(5)yearsfromthedateoforiginalpurchaseofthe
Equipmentorfive(5)yearsandsix(6)monthsfromthedateofshipmentfromthefactoryofthe
Equipment,thatitwillreplacethecompressorwithoneofsimilardesignandcapacity,exclusiveofdelivery
andinstallationcharges,ifitisfoundsubjecttoSilverKing’sreviewtobeinefficientorinoperativedueto
defectsinmaterialorfactoryworkmanship.Itistheoriginalpurchaser’sresponsibilitytoreturntheserial
plateofthedefectivecompressor,oratSilverKing’soptionthecompletecompressor,tothefactory.
Failuretodosowillvoidthislimitedcompressorwarranty.Thislimitedcompressorwarrantyshallbe
limitedtopartsonlyaftertheWARRANTYperiodapplicabletotheEquipmenthasexpired.

ThisEquipmentwarrantyislimitedtorepairingorreplacinganypartsthat,atSilverKing’sdiscretion,are
deemedtobedefectivewithinthetimeperiodcoveredbythiswarranty.Thethree(3)yearpartswarranty
coversstandardfreightandhandlingcharges.Specialhandlingchargesorexpeditedmeansfortransport
areexcludedfromreimbursement.Useofnon‐OEMpartsmay,atSilverKing’sdiscretion,voidthis
warranty.Ifapproved,warrantycreditfornon‐OEMpartswillbeissuedattheOEMcost.Replacement
partssoldseparatelyarewarrantedfor90‐daysfromdateofpurchase.Specialinstallation/applications,
includingremotelocations,arelimitedincoveragebythiswarranty.Anyinstallationthatrequiresextra
work,andortravel,isthesoleresponsibilityoftheequipmentpurchaser.
ADDITIONALWARRANTYGUIDELINES:AfactoryissuedServiceAuthorizationNumbermustbeobtained
priortoworkbeingperformedunderthe(1)one‐yearlaborwarranty.ContactyoursupplierorSilverKing.
ClaimssubmittedwithoutaServiceAuthorizationNumberwillbepaidatSilverKing’sdiscretion.Thelabor
warrantyincludesstandardstraighttimelaborchargesinaccordancewithSilverKing’sLaborWarranty
Guidelinesandreasonabletraveltime,asdeterminedasdeterminedintheSilverKingtime–rateguide.

SilverKing,atitsdiscretion,mayrequestphotosduringorpriortoservicebeingdispatchedtovalidatea
technicalissue.Failuretocomplywiththerequestmayresultinthecostofservicebeingtheresponsibility
oftheservicerequestororsite.

Thelaborwarrantydoesnotcoveroriginalinstallation,startup,normaladjustmentsormaintenance.
Normaladjustmentsandmaintenanceinclude,butarenotlimitedto;temperaturecontroladjustments,
temperatureindicatorcalibrations,coilandfiltercleaning,orcondensatedraincleaning.

Asecondservicecallforarelatedfailureisnotcovered.

UseofrefrigerantsotherthanspecifiedontheEquipmentserialplatevoidsthewarranty.Allclaimsmust
include;modelandserialnumberofequipment,dateofpurchase,dateoffailure,andacopyoftheservice
invoicedetailingthedefectandserviceperformed.Noclaimwillbeprocessedwithoutthisinformation.All
claimsmustbefiledwithin30daysfromdateofservice.

PRODUCTORDERINGINFORMATIONCallustollfreeat1‐800‐328‐3329or1‐763‐923‐2441Faxusat1‐763‐
553‐1209

Visitwww.silverking.comforstockingdistributor,equipmentspecsandcurrentpricelistforyourarea.

SERVICE/PARTSORDERINGINFORMATIONCallustollfreeat1‐800‐328‐3329,prompt1EquipmentService
andTechSupportor2Parts


10


TERMSANDCONDITIONS•ThispricelistandconditionsareeffectiveJanuary1,2020andsupersedesall
previouspricelists.•WARRANTYperiodmayvaryfromcustomertocustomerandiscontractspecific.•All
pricesreflectpaymentinU.S.Dollars.•Pricesdonotincludeanyfreight,duty,ortaxes.•Pricingsubjectto
changewithoutnotice.•Noreturnsareacceptedwithoutpriorwrittenapprovalfromthefactory.AnRMA
(ReturnedMerchandiseAuthorization)formmustbecompletedandthenapprovedbySilverKing.Please
contactSilverKingfordetails.Restockingfeewillapply.•Allelectricalequipmentissinglephase.•Prices,
designs,andspecificationsaresubjecttochangewithoutnotice.•Paymentsviacreditcardaresubjecttoa
3.5%surcharge.•

Anyandallenvironmentalattributes,includingenvironmentaloffsetcreditrights,withrespecttoSilver
KingrefrigerationunitsmanufacturedafterSeptember1,2015,shallremainthepropertyofSilverKingand
arenottransferred.

INNOEVENTSHALLSILVERKINGBELIABLEFORCONSEQUENTIAL,SPECIALORPUNITIVEDAMAGES.THE
REMEDIESOFPURCHASERSETFORTHHEREINAREEXCLUSIVEANDTHETOTALLIABILITYOFSILVERKING,
WHETHERBASEDONCONTRACT,WARRANTY,NEGLIGENCE,INDEMNIFICATION,STRICTLIABILITY,TORT,OR
OTHERWISE,SHALLNOTEXCEEDTHEPURCHASEPRICEOFTHECOMPONENTUPONWHICHLIABILITYIS
BASED.SILVERKINGSHALLHAVENOOBLIGATIONORLIABILITYFORCONSEQUENTIALORSPECIAL
DAMAGES,INCLUDINGBUTNOTLIMITEDTOINDIRECT,PUNITIVEDAMAGES,LOSSOFUSE,LOSSOF
PRODUCT,DOWNTIMEORLOSTPROFITS,ARISINGOUTOR,RELATEDTOORCONNECTEDINANYWAY
WITHTHEPRODUCTORITSUSE.

SilverKing1600XeniumLane,Plymouth,MN55441‐3706www.silverking.com•1‐800‐328‐3329

©SilverKing2019PricesSubjectToChange

Note:AdditionalTermsandConditionsofsalemayapply.Notice:SpecificationsSubjecttoChangeWithout
Notice.Contactfactoryforspecificmodelagencyapproval.
