Sim-Lab X1-PRO User manual

INSTRUCTION MANUAL
X1-PRO INTEGRATED MONITOR MOUNT
SINGLE/TRIPLE
VERSION 1.2
Last updated: 11-09-2023

2|2 13
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (page 12) and make sure all the parts are delivered.
In this manual, we combined the single and triple integrated monitor mount. This is because we packaged
the triple version as an upgrade to the single one.
This product combines some products we normally offer separately. We encourage you to read the
product manuals for included products if this one doesn’t answer all of your questions. Please refer to the
following if needed:
www.sim-lab.eu/xero-play-pivots-manual
www.sim-lab.eu/vario-vesa-manual
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Tools needed:
6MM 13MM

3|3 13
183MM
or
7.2”
Slot-Nut M8
4X
1195MM
1X
M8 X 16
4X
Washer M8
4X
Corner
Bracket
2X
Profile 80X40
End-Cap
2X
A12
A3
A10
A7
A1
A4

4|4 13
Cap-Washer
M8
4X
Monitor Side
Plate
2X
Washer M8
(A10)
4X
Lock-Nut M8
4X
Washer M8
(DIN 988)
4X
M8 X 35
4X
Nut Cap M8
4X
A2
A9A5 A8
A10
A13
A11

5|5 13
4X
Cap-Washer
M8
4X
Washer M8
(DIN 988)
4X
M8 X 30 Slot-Nut M8
4X
A9 A6
A8 A12

6|6 13
See page 11 to assemble the
other side of the Vario VESA.
If you purchased the
‘Triple Upgrade’, please
continue on the next page.
M8 X 16
2X
Washer M8
2X
Vario VESA
Holder
1X
Slot-Nut M8
2X
D12
D11
D8
D1

7|7 13
Depends on monitor size
and intended angle.
M8 X 25
8X
Slot-Nut M8
8X
Pivot
Adapter
4X
C1
C5
C3

8|8 13
Instructions for the right side (B2)
are similar. See page 10 for the
orientation of the profile.
* Mind the orientation of the Slot-Nuts.
BUILD 2X
Profile 80X40
End-Cap
2X
M8 X 25
4X
Slot-Nut M8
4X
BP1
(LEFT)
1X
Pivot
Adapter
2X
C1
B1
B3
C3
C5

9|9 13
Adjust arm angles to your preference.
We included markings in the pivots.
Markings are placed in 10° increments.
120°
M8 X 40
4X
Nut M8
4X
C2
C4

10 |10 13
M8 X 16
4X
Washer M8
4X
Vario VESA
Holder
2X
D11
D8
D1
D12

11 |11 13
When parts D9 and D10 are installed like above,
monitors are easy to install in a neutral
position. Parts D9 can be adjusted to change
the tilt and/or height.
Parts D10 can be adjusted to adjust the monitor
sideways if needed, and fix it in place.
Vario VESA
Plate
1X
Vario VESA
Pin Holder
2X
M8 X 40
(Set Screw)
2X
M5 X 20
(Set Screw)
2X
M5 X 20
4X
Vario VESA
Pin
1X
D3
D2
D9
D5
D10
D10
D9
D4

12 |12 13
BOX B - TRIPLE MONITOR MOUNT
PROFILE KIT
#Part QTY Note
B1 80X40 3N Length=580mm 1 Left arm, engraved.
B2 80X40 3N Length=580mm 1 Right arm, engraved.
HARDWARE KIT
B3 Profile 80x40 end-cap 4
BOX C - Xero-Play triple pivot set
HARDWARE KIT
#Part QTY Note
C1 Xero-Play triple pivot adapter 8
C2 Bolt M8 X 40 DIN 912 4
C3 Bolt M8 X 25 DIN 912 16
C4 Nut M8 4
C5 Slot-Nut M8 16
BOX A - SINGLE MONITOR MOUNT
PROFILE KIT
#Part QTY Note
A1 80X40 Length=1195mm 1
HARDWARE KIT
A2 Monitor side plate 2
A3 Integrated monitor corner bracket 2
A4 Profile 80x40 end-cap 2
A5 Bolt M8 X 35 DIN 912 4
A6 Bolt M8 X 30 DIN 912 4
A7 Bolt M8 X 16 DIN 912 4
A8 Cap-Washer M8 8
A9 Washer M8 DIN 988 8
A10 Washer M8 DIN 125-A 8
A11 Lock-Nut M8 4
A12 Slot-Nut M8 8
A13 Nut Cap M8 4
BOX D - Vario VESA adapter set (x1 or x3 depending on purchase)
HARDWARE KIT
#Part QTY Note
D1 Vario VESA holder 1
D2 Vario VESA plate 1
D3 Vario VESA pin holder 2
D4 Vario VESA pin 1
D5 Bolt M5 X 20 DIN 7991 4
D6 Screw M4 X 16 DIN 7985 4 Philips head.
D7 Screw M4 X 10 DIN 7985 4 Philips head.
D8 Bolt M8 X 16 DIN 912 2
D9 Set screw M8 X 40 DIN 916 3
D10 Set screw M5 X 20 DIN 916 2
D11 Washer M8 DIN 125-A 2
D12 Slot-Nut M8 2
D13 Standoff M4 x 10 4
Disclaimer: for some entries on this page, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.

13 |13 13
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: