Sim-Lab EVO User manual

FRONT MOUNT EVO
VERSION 1.5
Last updated: 24-02-2022
INSTRUCTION MANUAL

2|2 11
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (page 10) and make sure all the parts are delivered.
Breaking tabs:
Sometimes tabs from corner brackets need to be broken off in
order to fit as instructed. Place a flathead screwdriver behind
the tab and tilt upwards.
Always make sure to point away from you while doing so.
To know when to do this, we will show the following
symbol next to the brackets.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Tools needed:
5/6MM - 13MM

3|3 11
Corner
Bracket
4X
M8 X 16
(re-used)
4X
Slot-Nut M8
(re-used)
4X
500MM
(re-used)
1X
Parts re-used (R) from your existing
GT1-EVO build.
The corner brackets are from the Front
Mount hardware kit since they need to
retain their aligning tabs.
Brackets from your existing GT1-EVO build
with their tabs broken off, can be re-used
as well. We’ll show this on Page 6.
A4
R
R
R

4|4 11
Slot-Nut M8
6X
Slot-Nut M8
(re-used)
4X
A14
R

5|5 11
Corner Bracket
Cap (re-used)
4X
M8 X 16
(re-used)
4X
R
R

6|6 11
Front Mount
1X
Corner
Bracket**
4X
M8 X 30
(A9)
4X
Lock-Nut M8
4X
In case you are converting your original
GT1-EVO to a Front Mount, you can re-use
the original brackets which held the wheel
deck in place.
A15
A9
A4
A1

7|7 11
M8 X 25
(A10)
4X
Lock-Nut M8
4X
Corner Bracket
Cap
4X
Front Mount
Side Plate Right
1X
Front Mount
Side Plate LEFT
1X
A5
A3
A2
A15
A10

8|8 11
480MM
or
18,9”
10MM
or
0,4”
LEFT:
GT1-EVO PURCHASED
PRE-2020, OFFSET 10MM.
RIGHT:
CURRENT GT1-EVO,
SIDES FLUSH WITH FRONT MOUNT.

9|9 11
M8 X 20
6X
Washer M8
6X
A7
A12

10 |10 11
HARDWARE KIT
#Part QTY Note
A1 Front mount 1
A2 Front mount side plate LEFT 1
A3 Front mount side plate RIGHT 1
A4 Corner bracket 40x40 4
A5 Corner bracket 40x40 cap 4
A6 Bolt M8 X 40 DIN 912 4
A7 Bolt M8 X 20 DIN 912 8
A8 Bolt M6 X 20 DIN 912 4
A9 Bolt M8 X 30 DIN 7991 4 Countersunk
A10 Bolt M8 X 25 DIN 7991 4 Countersunk
A11 Bolt M8 X 16 DIN 7991 2 Countersunk
A12 Washer M8 DIN 125-A 12
A13 Spacer male/female M6 X 10 4
A14 Slot-Nut M8 10
A15 Lock-Nut M8 14
Disclaimer: for some entries on this list, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.

11 |11 11
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: