Sim-Lab GT1-EVO User manual

PEDAL SLIDER BASEPLATE
VERSION 1.4
Last updated: 22-03-2022
INSTRUCTION MANUAL

2|2 17
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (page 14) and make sure all the parts are delivered.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Tools needed:
Compatibility:
This accessory is compatible with more than one of our products. The main two ways of attaching our
(seat) sliders to our cockpits are either directly on profile or on a pedal deck. This manual shows both of
these options using a P1-X pedal deck (profile) and a GT1-EVO pedal deck (plate). However, compatibility
of this accessory is not limited to these cockpits. Please see the product page for more information on
compatibility.
4/5/6MM 8/10/13MM

3|3 17
361MM
or
14.21”
332MM
or
13.07”
Going to install the optional seat
sliders? Please skip to page 5.
Slot-Nut M8
4X
A10

4|4 17
Going to install the optional heel
rest? Please skip to page 11.
Spacer
M8 X 15
4X
M8 X 20
4X
Pedal
Base Plate
1X 4X
Washer M8
A1
A7
A8
A6

5|5 17
361MM
or
14.21”
326MM
or
12.83”
Using a GT1-EVO style pedal
deck? Please skip to page 12.
Slot-Nut M8
4X
A10

6|6 17
M8 X 12
2X
Seat Slider
LEFT
Seat Slider
RIGHT
1X1X
B1
A3
B2

7|7 17
50MM
or
1.96”
M8 X 12
2X
B
A
A3

8|8 17
Spacer
M8 X 15
2X
Lock-Nut M8
2X
2X
Washer M8
B
A
A8
A10
A7

9|9 17
Seat Slider Handle*
For the handle to fit snugly between the
sliders, it needs to be widened a bit by bending
it until it seats properly. Please review our seat
slider installation video for reference.
Spacer
M8 X 15
2X
Lock-Nut M8
2X
Seat Slider
Handle*
1X 2X
Washer M8
A10
A8
B
A
B3
A7

10 |10 17
M8 X 20
4X
Pedal
Base Plate
1X
A1
A6

11 |11 17
Plastic Sleeve
M8 X 10/20
4X
Lock-Nut M6
4X
Heel Rest
1X
M6 X 40
4X
OR
Heel Rest
C2
C1
C4
C7
C5

12 |12 17
Seat Slider
LEFT
Seat Slider
RIGHT
1X1X
M8 X 16
2X 2X
Washer M8 Lock-Nut M8
2X
B1
B2
A2
A10
A7

13 |13 17
Please continue on
page 8.
M8 X 16
2X 2X
Washer M8 Lock-Nut M8
2X
A10
A2
A
B
A7

14 |14 17
HEEL REST (optional purchase)
C1 Heel rest 1
C2 Bolt M6 X 40 DIN 7991 4 Countersunk
C3 Bolt M6 X 35 DIN 7991 4 Countersunk
C4 Plastic sleeve M8 X 20 4
C5 Plastic sleeve M8 X 10 4
C6 Slot-Nut M6 4
C7 Lock-Nut M6 4
Disclaimer: for some entries on this list, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.
PEDAL BASE PLATE
#Part QTY Note
A1 Pedal base plate 1
A2 Bolt M8 X 16 DIN 912 4
A3 Bolt M8 X 12 DIN 912 4
A4 Bolt M6 X 20 DIN 912 12
A5 Bolt M5 X 25 DIN 912 12
A6 Bolt M8 X 20 DIN 7991 4 Countersunk
A7 Washer M8 DIN 125-A 8
A8 Spacer male/female M8 X 15 4
A9 Slot-Nut M8 6
A10 Lock-Nut M8 6
A11 Lock-Nut M6 12
A12 Lock-Nut M5 12
SEAT SLIDER (optional purchase)
#Part QTY Note
B1 Seat slider LEFT 1
B2 Seat slider RIGHT 1
B3 Seat slider handle 1

15 |15 17
BJ F1/GT
Heusinkveld Ultimate
VRS DirectForce Pro Heusinkveld Pro
(only throttle and brake)
Logitech GXXX Pedals
Thrustmaster T-LCM
(only top row bolts)
Heusinkveld Sprint

16 |16 17
Fanatec CSP V3
Thrustmaster 2 pedal set
Thrustmaster T3PA
Fanatec CSL (3 pedals)
(use 6mm bolt and washer for slot)
Fanatec CSL (2 pedals)
(use 6mm bolt and washer for slot)

17 |17 17
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website:Seat Slider installation on YouTube: