Sim-Lab VESA 75/100 User manual

INTEGRATED MONITOR MOUNT VESA 75/100
VERSION 2.0
Last updated: 05-11-2021
INSTRUCTION MANUAL

2|2 10
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (page 10) and make sure all the parts are delivered.
Breaking tabs:
Sometimes tabs from corner brackets need to be broken off in
order to fit as instructed. Place a flathead screwdriver behind
the tab and tilt upwards.
Always make sure to point away from you while doing so.
To know when to do this, we will show the following
symbol next to the brackets.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
5/6MM -+
Tools needed:

3|3 10
680MM
1X
Slot-Nut M8
(A15)
2X 2X
Slot-Nut M6
(A16)
A16
P1
A15

4|4 10
200MM
2X
Slot-Nut M8
6X
A15
P2

5|5 10
Corner
Bracket
2X
M8 X 16
4X
Washer M8
4X
A5
A9
A11

6|6 10
Corner Bracket
Cap
2X
Profile
End-Cap
4X
VESA M6 X 16
2X1X
A6
A7
A10
A3

7|7 10
Monitor
Bracket
2X
M8 X 25
4X
Washer M8
4X
A4
A11
A8

8|8 10
PROFILE KIT
#Part QTY Note
P1 40X40 Length=680mm 1
P2 40X40 Length=200mm 2
HARDWARE KIT
A3 VESA bracket L-shape 1
A4 Integrated monitor bracket 2
A5 Corner bracket 40x40 2
A6 Corner bracket 40x40 cap 2
A7 Profile 40x40 end-cap 4
A8 Bolt M8 X 25 DIN 912 10
A9 Bolt M8 X 16 DIN 912 4
A10 Bolt M6 X 16 DIN 912 2
A11 Washer M8 DIN 125-A 16
A12 Screw Philips M4 X 16 DIN 7985 4 Extra
A13 Screw Philips M4 X 10 DIN 7985 4 Extra
A14 Spacer male/female M4 X 10 4 Extra
A15 Slot-Nut M8 16
A16 Slot-Nut M6 2
Disclaimer: for some entries on this list, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.

9|9 10
Mounting suggestion:
We advise to divide three bolts over two profile slots.
A8
A11

10 |10 10
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
https://discord.gg/Myj4c8dZ
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: