Sim-Lab PODIUM BRACKET SET User manual

PODIUM BRACKET SET
VERSION 1.0
Last updated: 09-06-2023
INSTRUCTION MANUAL

2|2 7
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Tools needed:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on
assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before
starting (page 6) and make sure all the parts are delivered.
Notes:
Depending on the hardware used, assembly might differ. When used with the CSL-DD/DD-Pro, use the spacers
as indicated on page 4.
Example installation is shown on a P1-X, however this Podium Bracket Set is also compatible with the GT1-EVO.
For a GT1-EVO OLDER than 2020, compatibility has been dropped.
BEFORE YOU START:
5/6MM

3|3 7
INSTRUCTIONS FOR
FANATEC DD1/DD2
CONTINUE
ON PAGE 5
Side Mount
Profile Holder Left
1X
M8 X 20
(A10)
8X
AP1
2X
Side Mount
Profile Holder Right
1X
Side Mount
Base Holder Left
1X
Side Mount
Base Holder Right
1X
A10
AP1
A5
A3
A4
A6

4|4 7
INSTRUCTIONS FOR
FANATEC CSL-DD/DD-PRO
CONTINUE
ON PAGE 5
Side Mount
Profile Holder Left
1X
M8 X 20
(A10)
4X
AP1
2X
Side Mount
Profile Holder Right
1X
Side Mount
Base Holder Left
1X
Side Mount
Base Holder Right
1X
Side Mount
Spacer
2X
M8 X 25
(A9)
4X
A5
A2
A2
A3
A4
A6
A10
A9
AP1

5|5 7
EXAMPLE ON P1-X
M8 X 20
(A7)
6X
Washer M8
(A12)
6X A12
A7

6|6 7
PODIUM BRACKET SET
PROFILE KIT
AP1 80X40 2 Threaded M8
HARDWARE KIT
A2 Side mount spacer 2 Use with CSL-DD/DD-PRO.
A3 Side mount base holder LEFT 1
A4 Side mount base holder RIGHT 1
A5 Side mount profile holder LEFT 1
A6 Side mount profile holder RIGHT 1
A7 Bolt M8 X 20 DIN 912 8
A8 Bolt M6 X 20 DIN 912 4
A9 Bolt M8 X 25 DIN 7991 4 Countersunk
A10 Bolt M8 X 20 DIN 7991 8 Countersunk
A11 Bolt M6 X 20 DIN 7991 4 Countersunk
A12 Washer M8 DIN 125-A 8
A13 Washer M6 DIN 125-A 6
A14 Slot-Nut M8 8
Disclaimer: for some entries on this list, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.

7|7 7
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: