Simaudio MOON VOICE 22 User manual

Voice 22

2
Introduction
Set up
Connection
Placement
Care
Specifications
Date code : 20210809-01
3
4
5
6
7
8
Table of Contents

3
Congratulations! You are now the proud owner of a pair of MOON Voice 22 loudspeakers!
We have applied our four decades of audio design experience to create these beautiful loudspeakers.
Featuring premium materials and industry-leading technologies,
they bring the renowned MOON sound to life.
We hope they provide a lifetime of listening pleasure.
Please follow these simple guidelines to get the most out of your new loudspeakers.
1Introduction

4
Contents
• Loudspeakers (2) • Hover Bases (2, preinstalled) • Grilles (2) • Foam Dampeners (2)
• Owner’s Guide • Warranty
Assembly
1. Holding the sides of the cabinets and avoiding placing hands on their front and rear baffles,
carefully remove each loudspeaker from the packaging.
2. Gently snap the magnetic speaker grilles onto the fronts of the Voice 22 cabinets.
3. Leave the Hover Bases attached to the cabinets.
Remove if installing with the matching MOON stand. Insert a finger in the designated opening
atthe rear of the Hover Base to pull it away.
4. Clear an appropriate space for the loudspeakers on a flat, level surface, and move the stands
orcabinets into place. When using stands, move the stands first and then the cabinets.
Do not attempt to move them together.
5. Connect the speaker cables (not included) to the binding posts on the rear of each cabinet.
2Setup

5
1. Ensure that electronic components —e.g.,amplifiers—
arepowered down before connecting
ordisconnectingcables.
2. Connect a cable from the positive (indicated in red
orbya“+”) output terminal of the amplifier tothered
terminal onthe rear of the speaker cabinet.
Connect the negative amplifier output from the same
amplifier channel to the black speaker terminal(DrawingA).
3. Connector Types:
• If your cable is terminated with banana pins,
theyshould slide into the holes at the end of the posts.
• If not, unscrew the colored cylinder around the metal
post to expose a second hole, insert the bare wire
orspade connector, and tighten the cylinder to hold
thecable in place.
Drawing A
3Connection
- +

6
These loudspeakers are expertly designed todeliver
great performances without elaborate fine-tuning.
Ideally, ensure that the speakers align vertically
withthe listener’s ears. Position them equidistant
fromthe listener, forming a triangle with thelistener.
Rotate the speakers so that they fire toward
thelistener, aiming them slightly beyond the listening
position (Drawing B).
For best results, remove the protective grilles
andavoid positioning the loudspeakers in corners
ortight spaces. Where possible, maintain a space
between the loudspeakers and surrounding walls
equivalent to at least twice the dimensions
ofthecabinet (Drawing C).
If it is impossible to achieve sufficient distance
between a loudspeaker and the wall behind it,
lowfrequencies may sound bloated and sluggish.
Plugging the port on its rear with the included foam
dampener could reduce this effect.
4Placement
Drawing B
Drawing C

7
Regular maintenance of the Voice 22 is unnecessary. Despite the best intentions,
eventhemildest cleaning product could damage the finish on the cabinet.
For years of enjoyment, keep it out of direct sunlight.
Damage to the cabinet from abuse or improper care is not covered by the warranty
and cannot be repaired.
When cleaning is inevitable, use a dry microfiber cloth or a feather duster on the cabinet
andrefrain from contact with the speaker components.
5Care

8
Tweeter 29mm soft dome with waveguide
Woofer 155mm polypropylene cone
Sensitivity 89dB/2.83V/1m
Nominal Impedance 6Ω
Recommended Power 50W – 150W
Frequency Response ±3dB: 55Hz – 24kHz
Frequency Range -6dB: 45Hz – 30kHz
Crossover 1.5kHz
Dimensions (W x H x D) 20cm x 35cm x 29cm
Weight 10.5kg
6Specifications