Simply Shade Concrete Mount Kit User manual

Concrete
In-Ground
Wood
I n s t r u c t i o n M a n u a l
Mount Kits
www.simplyshade.com
©2015 Simply Shade - All Rights Reserved. 7/15

1
CA TION: HANDLE WITH CARE
• To reduce personal injury and damage, read and follow this Assembly and
Operation information.
• Close the umbrella in windy conditions or when a storm approaches. Never
allow the umbrella to flap in the wind; this could damage the canopy.
• Do not leave open umbrella unattended.
• Do not allow children to play on or with the base.
WARRANTY:
The manufacturer warrants that this
umbrella, when subject to normal and
proper use, will be free from
manufacturing defects for a period of
one year from the original date of
purchase. Should any defect occur
during the specified time period, the
manufacturer will repair, replace, or
provide replacement parts, at its own
option. Limited warranty against fabric
fading, based on fabric grade. Warranty
is not transferable.
We will not warrant any claim coverage
unless both the original sales receipt and
request form are sent to us. Any items
that are returned for warranty or non
warranty purposes must be issued a
Return Authorization Number. Only
upon issuance of an RA# and inspection
by our QC department will credit or
replacement of umbrella be issued. It is
the customer’s responsibility to pay the
freight on return products or
replacement parts. ALL RETURNED
ITE S UST INCLUDE THE RA#
CLEARLY WRITTEN ON THE
RETURN PACKAGE or package will be
refused by our warehouse personnel.
NOTE: Damages and failure caused by
improper use due to neglect of reasonable
and necessary care are not covered by
this warranty.
Additionally, acts of nature (including but
not limited to wind, hurricanes, tornadoes,
and storms) are not covered by this
warranty.
Please remove all contents from the package, inspect and review check list.
CAUTION: To reduce personal injury and damage to your mount kit or umbrella,
read and follow this instruction manual. Save information for future reference.
6
Concrete ount Kit check list:
A-Adapter Plate (8.5” diameter)
B-Screw Anchors 3/8” x 3” (4)
AB
C
B
A
D
In-Ground Fitting Kit check list:
A- Adapter Plate (8.5” diameter)
B-In-Ground Fitting
C-Stem Bolts (4)
D-Allen Wrench
Wooden Deck ount Kit check list:
A-Adapter Plate
B-Base Plate
C-Round Countersunk Bolts (4)--
D-Allen Wrench
B
A
OUNT KIT CHECK LIST
CD

At least
6” thick
Rotating Hub
AMK
Adapter Plate
Hub Bolts
& Washers
Screw
Anchors
2
Concrete ount Kit includes:
A-Adapter Plate (8.5” diameter)
B-Screw Anchors 3/8” x 3” (4)
CONCRETE OUNT KIT
S T E P 1 Bolt Adapter Plate
Bolt the adapter plate (countersunk holes faced down) to an existing concrete slab (or
through no thicker than 1” pavers or tiles adhered to a concrete slab) using the supplied
screw anchors. Use a 5/16” drill bit for holes.
S T E P 2 Attach Rotating Hub to Adapter Plate
Attach rotating hub to adapter plate using the hub bolts that came with your umbrella.
S T E P 3 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
A
B
5
DISCLAIMER:
THE SSAMK MO NTING KIT SHO LD ONLY BE PROFESSIONALLY
INSTALLED BY A LICENSED CONTRACTOR D LY Q ALIFIED TO PERFORM
THE INSTALLATION. SIMPLY SHADE ASS MES NO LIABILITY AND
EXPRESSLY DISCLAIMS ANY RESPONSIBILITY FOR INJ RIES OR DAMAGES
ARISING FROM OR RELATED TO THE FAIL RE OF B YER TO HAVE THE
SSAMK MO NTING KIT INSTALLED BY A LICENSED PROFESSIONAL
CONTRACTOR. SIMPLY SHADE MAKES NO WARRANTY EXCEPT AS
EXPRESSLY STATED HEREIN, AND NO WARRANTY EXCEPT TITLE TO
MATERIALS F RNISHED SHALL BE IMPLIED WITH RESPECT TO THIS
ORDER.
DISCLAIMER OF WARRANTIES: EXCEPT AS HEREIN EXPRESSLY SET
FORTH, THIS PROD CT IS SOLD “AS IS” AND “WITH ALL FA LTS”, AND
WITHO T ANY IMPLIED WARRANTY OF MERCHANTABILITY -- WHICH
WARRANTY IS HEREBY EXPRESSLY EXCL DED. THIS PROD CT IS SOLD
WITHO T ANY IMPLIED WARRANTY OF FITNESS FOR A PARTIC LAR
P RPOSE -- WHICH WARRANTY IS HEREBY EXPRESSLY EXCL DED.
MOREOVER, THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.”

3
Adapter
Bolts
Rotating Hub
Adapter
Plate
Hub Bolts
& Washers
Base Plate
S T E P 1 Adapter Plate
Locate adapter plate and place in desired location on the deck. The adapter plate should
overlap two deck planks evenly. Adjust the base plate so that the proper alignment is
ensured.
S T E P 2 Drilling Deck Planks
ark the four countersunk holes onto the deck for drilling. Drill four 10mm holes through
the deck planks for the round countersunk bolts. Remove enough deck screws or nails
from these planks to be able to install base plate underneath the planks.
S T E P 3 Attach Base and Adapter Plates to Deck Planks
Attach the base plate and adapter plate together, with the base plate under the deck and
the adapter plate on top of the deck planks, using four (4) round countersunk bolts (Note:
If deck is thicker, longer bolts will be required. A contractor can help determine appropriate
size bolts). Insert the (4) round countersunk downward through the top of the countersunk
holes on adapter plate, through the planks, and screw them into the threaded holes in the
bottom base plate. ake sure they are very tight.
S T E P 4 Fasten Deck Planks
Refasten the deck planks to the joists by attaching removed screws from Step 2 in the
original holes closest to the base plate. Two structural deck screws should be used on
either side of the base plate in each plank.
S T E P 5 Attach Rotating Hub to Adapter Plate
Attach rotating hub to adapter plate using the hub bolts and washers that came with your
umbrella.
S T E P 6 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
WOODEN DECK OUNT KIT
Wooden Deck ount Kit
includes:
A-Adapter Plate
B-Base Plate
C-Round Countersunk Bolts (4)
D-Allen Wrench
4
IN-GROUND OUNT KIT
S T E P 1 Preparation
The in-ground fitting should or can be
built into newly poured concrete. For a
perfect flush mount, set the plate of the
fitting 3/8” below the final surface grade.
When you add the 3/8” thick adapter
plate to the fitting plate, the adapter
plate will be flush with the concrete.
S T E P 2 Bolt Adapter Plate
Once installed and the concrete has
cured, bolt the adapter plate
(countersunk holes face up) to the top of
the in-ground fitting using the four (4)
stem bolts and allen wrench. Insert the
stem bolts downward through the
countersunk holes in the adapter plate
and screw them into the threaded holes
in the top of the in-ground fitting. ake
sure they are very tight.
S T E P 3 Attach Rotating Hub
Attach rotating hub to adapter plate using the hub bolts that came with your umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
I PORTANT: When concreting the in-ground fitting in place, make sure not to get slurry
in the screw threads. Either apply tape over the holes on both sides of the fitting or place
the stem bolts in the threads and withdraw them when the concrete is set. ake sure that
the
in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time
for your area before installing the umbrella onto the fitting.
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
C
B
Ground Level
Concrete Footing
Flare at
bottom
1.0m
or
3’4”
In-Ground
Fitting
AMK
Adapter Plate
Ground
Stem Bolts
Rotating Hub
Hub Bolts
& Washers
Hole Diameter
500mm or 21” - 24”
A
D
In-Ground Fitting Kit includes:
A-Adapter Plate (8.5” diameter) C-Stem Bolts (4)
B-In-Ground Fitting D-Allen Wrench
B
A
CD

3
Adapter
Bolts
Rotating Hub
Adapter
Plate
Hub Bolts
& Washers
Base Plate
S T E P 1 Adapter Plate
Locate adapter plate and place in desired location on the deck. The adapter plate should
overlap two deck planks evenly. Adjust the base plate so that the proper alignment is
ensured.
S T E P 2 Drilling Deck Planks
ark the four countersunk holes onto the deck for drilling. Drill four 10mm holes through
the deck planks for the round countersunk bolts. Remove enough deck screws or nails
from these planks to be able to install base plate underneath the planks.
S T E P 3 Attach Base and Adapter Plates to Deck Planks
Attach the base plate and adapter plate together, with the base plate under the deck and
the adapter plate on top of the deck planks, using four (4) round countersunk bolts (Note:
If deck is thicker, longer bolts will be required. A contractor can help determine appropriate
size bolts). Insert the (4) round countersunk downward through the top of the countersunk
holes on adapter plate, through the planks, and screw them into the threaded holes in the
bottom base plate. ake sure they are very tight.
S T E P 4 Fasten Deck Planks
Refasten the deck planks to the joists by attaching removed screws from Step 2 in the
original holes closest to the base plate. Two structural deck screws should be used on
either side of the base plate in each plank.
S T E P 5 Attach Rotating Hub to Adapter Plate
Attach rotating hub to adapter plate using the hub bolts and washers that came with your
umbrella.
S T E P 6 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
WOODEN DECK OUNT KIT
Wooden Deck ount Kit
includes:
A-Adapter Plate
B-Base Plate
C-Round Countersunk Bolts (4)
D-Allen Wrench
4
IN-GROUND OUNT KIT
S T E P 1 Preparation
The in-ground fitting should or can be
built into newly poured concrete. For a
perfect flush mount, set the plate of the
fitting 3/8” below the final surface grade.
When you add the 3/8” thick adapter
plate to the fitting plate, the adapter
plate will be flush with the concrete.
S T E P 2 Bolt Adapter Plate
Once installed and the concrete has
cured, bolt the adapter plate
(countersunk holes face up) to the top of
the in-ground fitting using the four (4)
stem bolts and allen wrench. Insert the
stem bolts downward through the
countersunk holes in the adapter plate
and screw them into the threaded holes
in the top of the in-ground fitting. ake
sure they are very tight.
S T E P 3 Attach Rotating Hub
Attach rotating hub to adapter plate using the hub bolts that came with your umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
I PORTANT: When concreting the in-ground fitting in place, make sure not to get slurry
in the screw threads. Either apply tape over the holes on both sides of the fitting or place
the stem bolts in the threads and withdraw them when the concrete is set. ake sure that
the
in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time
for your area before installing the umbrella onto the fitting.
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
C
B
Ground Level
Concrete Footing
Flare at
bottom
1.0m
or
3’4”
In-Ground
Fitting
AMK
Adapter Plate
Ground
Stem Bolts
Rotating Hub
Hub Bolts
& Washers
Hole Diameter
500mm or 21” - 24”
A
D
In-Ground Fitting Kit includes:
A-Adapter Plate (8.5” diameter) C-Stem Bolts (4)
B-In-Ground Fitting D-Allen Wrench
B
A
CD

At least
6” thick
Rotating Hub
AMK
Adapter Plate
Hub Bolts
& Washers
Screw
Anchors
2
Concrete ount Kit includes:
A-Adapter Plate (8.5” diameter)
B-Screw Anchors 3/8” x 3” (4)
CONCRETE OUNT KIT
S T E P 1 Bolt Adapter Plate
Bolt the adapter plate (countersunk holes faced down) to an existing concrete slab (or
through no thicker than 1” pavers or tiles adhered to a concrete slab) using the supplied
screw anchors. Use a 5/16” drill bit for holes.
S T E P 2 Attach Rotating Hub to Adapter Plate
Attach rotating hub to adapter plate using the hub bolts that came with your umbrella.
S T E P 3 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual
for further assistance.
You are now ready to operate your umbrella!
RE OVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction anual for further assistance on how to
remove umbrella.
A
B
5
DISCLAIMER:
THE MO NTING KIT SHO LD ONLY BE PROFESSIONALLY INSTALLED BY
A LICENSED CONTRACTOR D LY Q ALIFIED TO PERFORM THE
INSTALLATION. SIMPLY SHADE ASS MES NO LIABILITY AND EXPRESSLY
DISCLAIMS ANY RESPONSIBILITY FOR INJ RIES OR DAMAGES ARISING
FROM OR RELATED TO THE FAIL RE OF B YER TO HAVE THE
MO NTING KIT INSTALLED BY A LICENSED PROFESSIONAL
CONTRACTOR. SIMPLY SHADE MAKES NO WARRANTY EXCEPT AS
EXPRESSLY STATED HEREIN, AND NO WARRANTY EXCEPT TITLE TO
MATERIALS F RNISHED SHALL BE IMPLIED WITH RESPECT TO THIS
ORDER.
DISCLAIMER OF WARRANTIES: EXCEPT AS HEREIN EXPRESSLY SET
FORTH, THIS PROD CT IS SOLD “AS IS” AND “WITH ALL FA LTS”, AND
WITHO T ANY IMPLIED WARRANTY OF MERCHANTABILITY -- WHICH
WARRANTY IS HEREBY EXPRESSLY EXCL DED. THIS PROD CT IS SOLD
WITHO T ANY IMPLIED WARRANTY OF FITNESS FOR A PARTIC LAR
P RPOSE -- WHICH WARRANTY IS HEREBY EXPRESSLY EXCL DED.
MOREOVER, THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.”

1
CA TION: HANDLE WITH CARE
• To reduce personal injury and damage, read and follow this Assembly and
Operation information.
• Close the umbrella in windy conditions or when a storm approaches. Never
allow the umbrella to flap in the wind; this could damage the canopy.
• Do not leave open umbrella unattended.
• Do not allow children to play on or with the base.
WARRANTY:
The manufacturer warrants that this
umbrella, when subject to normal and
proper use, will be free from
manufacturing defects for a period of
one year from the original date of
purchase. Should any defect occur
during the specified time period, the
manufacturer will repair, replace, or
provide replacement parts, at its own
option. Limited warranty against fabric
fading, based on fabric grade. Warranty
is not transferable.
We will not warrant any claim coverage
unless both the original sales receipt and
request form are sent to us. Any items
that are returned for warranty or non
warranty purposes must be issued a
Return Authorization Number. Only
upon issuance of an RA # and inspection
by our QC department will credit or
replacement of umbrella be issued. It is
the customer’s responsibility to pay the
freight on return products or
replacement parts. ALL RETURNED
ITE S UST INCLUDE THE RA#
CLEARLY WRITTEN ON THE
RETURN PACKAGE or package will be
refused by our warehouse personnel.
NOTE: Damages and failure caused by
improper use due to neglect of reasonable
and necessary care are not covered by
this warranty.
Additionally, acts of nature (including but
not limited to wind, hurricanes, tornadoes,
and storms) are not covered by this
warranty.
Thank you for your purchase of SimplyShade’s SSA K ount Kit.
Please remove all contents from the package, inspect and review check list.
CAUTION: To reduce personal injury and damage to your mount kit or umbrella,
read and follow this instruction manual. Save information for future reference.
6
Concrete ount Kit check list:
A-Adapter Plate (8.5” diameter)
B-Screw Anchors 3/8” x 3” (4)
AB
C
B
A
D
In-Ground Fitting Kit check list:
A- Adapter Plate (8.5” diameter)
B-In-Ground Fitting
C-Stem Bolts (4)
D-Allen Wrench
Wooden Deck ount Kit check list:
A-Adapter Plate
B-Base Plate
C-Round Countersunk Bolts (4)--
D-Allen Wrench
B
A
OUNT KIT CHECK LIST
CD

Concrete / SSAMK-C
In-Ground / SSAMK-G
Wood / SSAMK-W
I n s t r u c t i o n M a n u a l
Mount Kits
www.simplyshade.com
©2015 Simply Shade - All Rights Reserved. 7/15