Simply Shade SSAMK Series User manual

Concrete / SSAMK-C
In-Ground / SSAMK-G
Wood / SSAMK-W
Instruction Manual
Mount Kits
www.simplyshade.com
©2019 SimplyShade - All Rights Reserved. 11/19

1
CA TION: HA DLE WITH CARE
• To reduce personal injury and damage, read and follow this Assembly and
Operation information.
• Close the umbrella in windy conditions or when a storm approaches. ever
allow the umbrella to flap in the wind; this could damage the canopy.
• Do not leave open umbrella unattended.
• Do not allow children to play on or with the base.
WARRA TY:
The manufacturer warrants that this
umbrella, when subject to normal and
proper use, will be free from
manufacturing defects for a period of
one year from the original date of
purchase. Should any defect occur
during the specified time period, the
manufacturer will repair, replace, or
provide replacement parts, at its own
option. Limited warranty against fabric
fading, based on fabric grade. Warranty
is not transferable.
We will not warrant any claim coverage
unless both the original sales receipt and
request form are sent to us. Any items
that are returned for warranty or non
warranty purposes must be issued a
Return Authorization umber. Only
upon issuance of an RA # and inspection
by our QC department will credit or
replacement of umbrella be issued. It is
the customer’s responsibility to pay the
freight on return products or
replacement parts. ALL RETUR ED
ITEMS MUST I CLUDE THE RA#
CLEARLY WRITTE O THE
RETUR PACKAGE or package will be
refused by our warehouse personnel.
OTE: Damages and failure caused by
improper use due to neglect of reasonable
and necessary care are not covered by
this warranty.
Additionally, acts of nature (including but
not limited to wind, hurricanes, tornadoes,
and storms) are not covered by this
warranty.
Thank you for purchasing SimplyShade’s SSAMK Mount Kit.
Please remove all contents from the package, inspect and review check list.
CAUTIO : To reduce personal injury and damage to your mount kit or umbrella,
read and follow this instruction manual. Save information for future reference.
6
Concrete Mount Kit check list:
A - Adapter Plate A (8.5” diameter)
B - Bolt Anchors (4)
C - Double Expansion Concrete Anchors (4)
D - Hex Wrench
AB
C
B
A
D
In-Ground Fitting Kit check list:
A- Adapter Plate A (8.5” diameter)
B - In-Ground Fitting
C - Stem Bolts (4)
D - Hex Wrench
Wooden Deck Mount Kit check list:
A - Adapter Plate A (8.5” diameter)
B - Base Plate
C - Countersunk Bolts (4)
D - Hex Wrench
B
A
MOU T KIT CHECK LIST
CD
CD

Rotating Hub
Hub Bolts
&Washers
Double Expansion
Concrete Anchor
Adapter
Plate A
(included with
umbrella)
(included with
umbrella)
(
At least
6” thick
Bolt Anchor
Concrete
2
Concrete Mount Kit includes:
A - Adapter Plate A (8.5” diameter)
B - Countersunk Bolt Anchors (4)
C - Double Expansion Concrete Anchors (4) (3/8” dia., 3/4” drill, 1-1/2” OAL)
C - Hex Wrench
CO CRETE MOU T KIT
A
B
5
DISCLAIMER:
THE SSAMK MO NTING KIT SHO LD ONLY BE PROFESSIONALLY
INSTALLED BY A LICENSED CONTRACTOR D LY Q ALIFIED TO PERFORM
THE INSTALLATION. SIMPLY SHADE ASS MES NO LIABILITY AND
EXPRESSLY DISCLAIMS ANY RESPONSIBILITY FOR INJ RIES OR DAMAGES
ARISING FROM OR RELATED TO THE FAIL RE OF B YER TO HAVE THE
SSAMK MO NTING KIT INSTALLED BY A LICENSED PROFESSIONAL
CONTRACTOR. SIMPLY SHADE MAKES NO WARRANTY EXCEPT AS
EXPRESSLY STATED HEREIN, AND NO WARRANTY EXCEPT TITLE TO
MATERIALS F RNISHED SHALL BE IMPLIED WITH RESPECT TO THIS
ORDER.
DISCLAIMER OF WARRANTIES: EXCEPT AS HEREIN EXPRESSLY SET
FORTH, THIS PROD CT IS SOLD “AS IS” AND “WITH ALL FA LTS”, AND
WITHO T ANY IMPLIED WARRANTY OF MERCHANTABILITY -- WHICH
WARRANTY IS HEREBY EXPRESSLY EXCL DED. THIS PROD CT IS SOLD
WITHO T ANY IMPLIED WARRANTY OF FITNESS FOR A PARTIC LAR
P RPOSE -- WHICH WARRANTY IS HEREBY EXPRESSLY EXCL DED.
MOREOVER, THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.”
C
D
S T E P 1 Bolt Double Expansion Concrete Anchors
Final installation hardware should be determined by and professionally installed by a
license contractor. During installation, make sure all adapter plate holes align with drilled
holes in concrete. Clean out each hole of all debris. Insert (4) double expansion concrete
anchors into holes and tap the fastener lightly with a hammer to ensure they are seated
correctly. When using supplied double expansion concrete anchors, make sure thread side
is down, towards the bottom of the hole and they are flush with the concrete slab.
S T E P 2 Bolt Adapter Plate A
Set adapter plate A over double expansion concrete anchors. Insert (4) countersunk bolt
anchors through adapter plate and into the double expansion concrete anchors. Tighten all
(4) countersunk bolt anchors with supplied hex wrench.
S T E P 3 Bolt Rotating Hub to Adapter Plate A
Align rotating hub holes with adapter plate holes. Insert (5) hub bolts and tighten using hex
wrench to secure. Note: Rotating hub and hub bolts are included with umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another adapter plate or
in-ground fitting, simply undo the hub bolts and remove the umbrella from the adapter
plate.

3
S T E P 1 Adapter Plate A
Final installation should be determined by and professionally installed by a license
contractor. Locate adapter plate A and place in desired location on the deck. The adapter
plate should overlap two deck boards equally. Adjust the adapter plate so that the proper
alignment is ensured.
S T E P 2 Drilling Deck Boards
Mark the four countersunk holes onto the deck for drilling. Drill four 10mm / 13⁄32” holes
through the deck boards for the countersunk bolts. Remove enough deck screws or nails
from these boards to be able to install base plate underneath the boards.
S T E P 3 Attach Base and Adapter Plates to Deck Boards
Using four (4) countersunk bolts, attach the base plate and adapter plate A together, with
the base plate under the deck and adapter plate A on top of the deck boards ( ote: If deck
is thicker, longer bolts may be required. A licensed contractor can help determine
appropriate size bolts). Insert the (4) countersunk bolts downward through the top of the
countersunk holes on adapter plate A, through the boards, and screw them into the
threaded holes in the bottom base plate. Tighten all (4) countersunk bolts with supplied
hex wrench.
S T E P 4 Fasten Deck Boards
Refasten the deck boards to the joists by attaching removed screws from Step 2 in the
original holes closest to the Base Plate. Two structural deck screws should be used on
either side of the base plate in each board.
S T E P 5 Bolt Rotating Hub to Adapter Plate A
Align rotating hub holes with adapter plate holes. Insert (5) hub bolts and tighten using hex
wrench to secure. Note: Rotating hub and hub bolts are included with umbrella.
S T E P 6 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another adapter plate or
in-ground fitting, simply undo the hub bolts and remove the umbrella from the adapter
plate.
WOODE DECK MOU T KIT
Wooden Deck Mount Kit includes:
A - Adapter Plate A (8.5” diameter)
B - Base Plate
C - Countersunk Bolts (4)
D - Hex Wrench
4
I -GROU D MOU T KIT
C
B
A
D
In-Ground Fitting Kit includes:
A - Adapter Plate A (8.5” diameter)
B - In-Ground Fitting
C - Stem Bolts (4)
D - Hex Wrench
B
A
C
S T E P 1 Preparation
Final installation should be determined
by and professionally installed by a
license contractor. Dig an approximate
60 cm/2 ft. deep by 90 cm/3 ft. wide
hole. Insert in-ground fitting and pour
mixed concrete into hole around fitting.
Make sure in-ground plate is level.
Note: Do not get slurry in the screw threads. Either apply tape over the holes on both
sides of the fitting or place the stem bolts in the threads and remove them when the
concrete is almost set. To make the adapter plate flush with the concrete, recess the in-
ground fitting 3/8” below the finished surface.
S T E P 2 Bolt Adapter Plate A
Once concrete has cured, bolt adapter plate A onto in-ground fitting. Insert (4) countersunk
stem bolts through adapter plate. Tighten all (4) stem bolts with supplied hex wrench.
S T E P 3 Bolt Rotating Hub to Adapter Plate A
Align rotating hub holes with adapter plate holes. Insert (5) hub bolts and tighten using hex
wrench to secure. Note: Rotating hub and hub bolts are included with umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another adapter plate or
in-ground fitting, simply undo the hub bolts and remove the umbrella from the adapter
plate.
D
Ground
Level
Concrete
Footing
60 cm/
2 ft.
In-Ground
Fitting
Stem Bolts
Rotating Hub
Hub Bolts
& Washers
Adapter
Plate A
(included with
umbrella)
(
(included with
umbrella)
Hole Diameter
90 cm / 3ft”
Countersunk
Bolts
Rotating Hub
Hub Bolts
& Washers
Adapter
Plate A
Base Plate
(included with
umbrella)
(included with
umbrella)

3
S T E P 1 Adapter Plate A
Final installation should be determined by and professionally installed by a license
contractor. Locate adapter plate A and place in desired location on the deck. The adapter
plate should overlap two deck boards equally. Adjust the adapter plate so that the proper
alignment is ensured.
S T E P 2 Drilling Deck Boards
Mark the four countersunk holes onto the deck for drilling. Drill four 10mm / 13⁄32” holes
through the deck boards for the countersunk bolts. Remove enough deck screws or nails
from these boards to be able to install base plate underneath the boards.
S T E P 3 Attach Base and Adapter Plates to Deck Boards
Using four (4) countersunk bolts, attach the base plate and adapter plate A together, with
the base plate under the deck and adapter plate A on top of the deck boards ( ote: If deck
is thicker, longer bolts may be required. A licensed contractor can help determine
appropriate size bolts). Insert the (4) countersunk bolts downward through the top of the
countersunk holes on adapter plate A, through the boards, and screw them into the
threaded holes in the bottom base plate. Tighten all (4) countersunk bolts with supplied
hex wrench.
S T E P 4 Fasten Deck Boards
Refasten the deck boards to the joists by attaching removed screws from Step 2 in the
original holes closest to the Base Plate. Two structural deck screws should be used on
either side of the base plate in each board.
S T E P 5 Bolt Rotating Hub to Adapter Plate A
Align rotating hub holes with adapter plate holes. Insert (5) hub bolts and tighten using hex
wrench to secure. Note: Rotating hub and hub bolts are included with umbrella.
S T E P 6 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another adapter plate or
in-ground fitting, simply undo the hub bolts and remove the umbrella from the adapter
plate.
WOODE DECK MOU T KIT
Wooden Deck Mount Kit includes:
A - Adapter Plate A (8.5” diameter)
B - Base Plate
C - Countersunk Bolts (4)
D - Hex Wrench
4
I -GROU D MOU T KIT
C
B
A
D
In-Ground Fitting Kit includes:
A - Adapter Plate A (8.5” diameter)
B - In-Ground Fitting
C - Stem Bolts (4)
D - Hex Wrench
B
A
C
S T E P 1 Preparation
Final installation should be determined
by and professionally installed by a
license contractor. Dig an approximate
60 cm/2 ft. deep by 90 cm/3 ft. wide
hole. Insert in-ground fitting and pour
mixed concrete into hole around fitting.
Make sure in-ground plate is level.
Note: Do not get slurry in the screw threads. Either apply tape over the holes on both
sides of the fitting or place the stem bolts in the threads and remove them when the
concrete is almost set. To make the adapter plate flush with the concrete, recess the in-
ground fitting 3/8” below the finished surface.
S T E P 2 Bolt Adapter Plate A
Once concrete has cured, bolt adapter plate A onto in-ground fitting. Insert (4) countersunk
stem bolts through adapter plate. Tighten all (4) stem bolts with supplied hex wrench.
S T E P 3 Bolt Rotating Hub to Adapter Plate A
Align rotating hub holes with adapter plate holes. Insert (5) hub bolts and tighten using hex
wrench to secure. Note: Rotating hub and hub bolts are included with umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another adapter plate or
in-ground fitting, simply undo the hub bolts and remove the umbrella from the adapter
plate.
D
Ground
Level
Concrete
Footing
60 cm/
2 ft.
In-Ground
Fitting
Stem Bolts
Rotating Hub
Hub Bolts
& Washers
Adapter
Plate A
(included with
umbrella)
(
(included with
umbrella)
Hole Diameter
90 cm / 3ft”
Countersunk
Bolts
Rotating Hub
Hub Bolts
& Washers
Adapter
Plate A
Base Plate
(included with
umbrella)
(included with
umbrella)

Rotating Hub
Hub Bolts
&Washers
Double Expansion
Concrete Anchor
Adapter
Plate A
(included with
umbrella)
(included with
umbrella)
(
At least
6” thick
Bolt Anchor
Concrete
2
Concrete Mount Kit includes:
A - Adapter Plate A (8.5” diameter)
B - Countersunk Bolt Anchors (4)
C - Double Expansion Concrete Anchors (4) (3/8” dia., 3/4” drill, 1-1/2” OAL)
C - Hex Wrench
CO CRETE MOU T KIT
A
B
5
DISCLAIMER:
THE SSAMK MO NTING KIT SHO LD ONLY BE PROFESSIONALLY
INSTALLED BY A LICENSED CONTRACTOR D LY Q ALIFIED TO PERFORM
THE INSTALLATION. SIMPLY SHADE ASS MES NO LIABILITY AND
EXPRESSLY DISCLAIMS ANY RESPONSIBILITY FOR INJ RIES OR DAMAGES
ARISING FROM OR RELATED TO THE FAIL RE OF B YER TO HAVE THE
SSAMK MO NTING KIT INSTALLED BY A LICENSED PROFESSIONAL
CONTRACTOR. SIMPLY SHADE MAKES NO WARRANTY EXCEPT AS
EXPRESSLY STATED HEREIN, AND NO WARRANTY EXCEPT TITLE TO
MATERIALS F RNISHED SHALL BE IMPLIED WITH RESPECT TO THIS
ORDER.
DISCLAIMER OF WARRANTIES: EXCEPT AS HEREIN EXPRESSLY SET
FORTH, THIS PROD CT IS SOLD “AS IS” AND “WITH ALL FA LTS”, AND
WITHO T ANY IMPLIED WARRANTY OF MERCHANTABILITY -- WHICH
WARRANTY IS HEREBY EXPRESSLY EXCL DED. THIS PROD CT IS SOLD
WITHO T ANY IMPLIED WARRANTY OF FITNESS FOR A PARTIC LAR
P RPOSE -- WHICH WARRANTY IS HEREBY EXPRESSLY EXCL DED.
MOREOVER, THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.”
C
D
S T E P 1 Bolt Double Expansion Concrete Anchors
Final installation hardware should be determined by and professionally installed by a
license contractor. During installation, make sure all adapter plate holes align with drilled
holes in concrete. Clean out each hole of all debris. Insert (4) double expansion concrete
anchors into holes and tap the fastener lightly with a hammer to ensure they are seated
correctly. When using supplied double expansion concrete anchors, make sure thread side
is down, towards the bottom of the hole and they are flush with the concrete slab.
S T E P 2 Bolt Adapter Plate A
Set adapter plate A over double expansion concrete anchors. Insert (4) countersunk bolt
anchors through adapter plate and into the double expansion concrete anchors. Tighten all
(4) countersunk bolt anchors with supplied hex wrench.
S T E P 3 Bolt Rotating Hub to Adapter Plate A
Align rotating hub holes with adapter plate holes. Insert (5) hub bolts and tighten using hex
wrench to secure. Note: Rotating hub and hub bolts are included with umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella instruction manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another adapter plate or
in-ground fitting, simply undo the hub bolts and remove the umbrella from the adapter
plate.

1
CA TION: HA DLE WITH CARE
• To reduce personal injury and damage, read and follow this Assembly and
Operation information.
• Close the umbrella in windy conditions or when a storm approaches. ever
allow the umbrella to flap in the wind; this could damage the canopy.
• Do not leave open umbrella unattended.
• Do not allow children to play on or with the base.
WARRA TY:
The manufacturer warrants that this
umbrella, when subject to normal and
proper use, will be free from
manufacturing defects for a period of
one year from the original date of
purchase. Should any defect occur
during the specified time period, the
manufacturer will repair, replace, or
provide replacement parts, at its own
option. Limited warranty against fabric
fading, based on fabric grade. Warranty
is not transferable.
We will not warrant any claim coverage
unless both the original sales receipt and
request form are sent to us. Any items
that are returned for warranty or non
warranty purposes must be issued a
Return Authorization umber. Only
upon issuance of an RA # and inspection
by our QC department will credit or
replacement of umbrella be issued. It is
the customer’s responsibility to pay the
freight on return products or
replacement parts. ALL RETUR ED
ITEMS MUST I CLUDE THE RA#
CLEARLY WRITTE O THE
RETUR PACKAGE or package will be
refused by our warehouse personnel.
OTE: Damages and failure caused by
improper use due to neglect of reasonable
and necessary care are not covered by
this warranty.
Additionally, acts of nature (including but
not limited to wind, hurricanes, tornadoes,
and storms) are not covered by this
warranty.
Thank you for purchasing SimplyShade’s SSAMK Mount Kit.
Please remove all contents from the package, inspect and review check list.
CAUTIO : To reduce personal injury and damage to your mount kit or umbrella,
read and follow this instruction manual. Save information for future reference.
6
Concrete Mount Kit check list:
A - Adapter Plate A (8.5” diameter)
B - Bolt Anchors (4)
C - Double Expansion Concrete Anchors (4)
D - Hex Wrench
AB
C
B
A
D
In-Ground Fitting Kit check list:
A- Adapter Plate A (8.5” diameter)
B - In-Ground Fitting
C - Stem Bolts (4)
D - Hex Wrench
Wooden Deck Mount Kit check list:
A - Adapter Plate A (8.5” diameter)
B - Base Plate
C - Countersunk Bolts (4)
D - Hex Wrench
B
A
MOU T KIT CHECK LIST
CD
CD

Concrete / SSAMK-C
In-Ground / SSAMK-G
Wood / SSAMK-W
Instruction Manual
Mount Kits
www.simplyshade.com
©2019 SimplyShade - All Rights Reserved. 11/19