Sipura SPA-2002 User manual

Please check to make sure that you have the following package contents:
1. Sipura Phone Adapter Unit
2. Ethernet Cable
3. SPA Quickstarl Guide (This Document)
4. 5 Volt Power Adapter
You will also need:
1. One or Two Analog Touch Tone Telephone (or Fax Machine)
2. Access to an lP Network via an Ethernet Connection
RJ-1 I to i=eleohone o. Fax
lPhone 1 - Lelt
Phse 2 - R€itl
SPA-2002 (Rear)
Please observe the following steps to install the SPA.
From Rear of the SPA-2002:
1. Insert a standard RJ-45 Ethernet cable (included) into the LAN port.
2. Insert the power adapter cable into the 5V powef adapter cable receptacle.
Ensure that the power adapter jack is snugly attached to the SPA.
3. lnsert a standard RJ-11 telephone cable intothe Phone 1 port.
4. Connect the other end of the cable to an analog telephone or fax machine.
5. Insert a standard RJ-11 telephone cable into the Phone 2 port (Optional).
6. Connect the other end of the cable to an analog telephone or fax machine.
Note: Do not connect RJ-1l tetephone cable from the SPA fo the watljack
to prevent any chance of connection to the circuit switched telco netwo*.
You may now insert the plug end of the power adapter into a live power outlet
which will power up the SPA.
svoh RJ4sEthenetb
PMr Cable/DslModemor
CFnndon Ntulk Ssfth

Preconfiguration of network and service settings may have been provided
by the service provider or network administrator who supplied this unit.
Depending on the configuration policy, end user access to local configuration
settings may be restricted or inaccessible. lf end user configuration is allowed,
some of the key network and service configuration setting instructions are
described in the fotlowing sections.
To locally configure the SPA, the user should have the following information from
their service provider or network administrator:
1. lP Address, Sub-Net and Gateway Addresses or DHCP Availability
2. SIP Proxy Address and Registration Information
3. Subscriber Information, e.g. User lD, Password
For advanced configuration information, please refer to the SPA
User Guide available in the Support section of Sipura's web site.
http :llwww. si p u ra. com/s u ppo rt
Enter IVR NIenU
Check DHCP 100# None IVR wll announce rf DrcP is er€bled or disab{ed
Set DHCP Enter 1 to enable
Enter 0 to disable Enter opton follo €d by *e pornd key.
Check lP Address Enter @tbn followed byt'e parnd key
Via a touch tone telephone attached to the Phone 1 or Phone 2 port on the SPA,
press the star key four times (* * * *) to enter the Sipura Configuration Menu.
Please see the below table for options and responses you may use to configure the
SPA to connect to the network.
lgno€ SIT or otr€r tsres untjl yc[i hear, "Spun
confnuraton nrenu. P16e enter octon bllo €d
by t16 por.rd key or har€-up to exit''
Set lP Address
Check Net Mask 124# None
Enter value using numbers on the
telephone key pad. Use the - (star)
key when entenng a decirnal point
Enter value folb\ ^ed by tl-. pound key. DHCP mLd
be "Dsabled'otf€rwise you will lrear 'lnvald Oplon,"
if vou w tc set his \€lue.
Enter option follo €d by fe pound key
Set Net Mask Enter value using numbers on the
telephone key pad. Use the - (sta|
key when entering a decmal point.
Enter value itloffed by tre purd key. DtCP m|xst
be "Disabled' otr€wise you wll iear ' Invalil Opton, '
ii you ty to sd tns value.
Check Gateway 130# None Enter optnn bllor€d by d'e oo."d key
Enter value using numbeB on the
telephone key pad. Use th€ - (slar)
key when entenng a deomal pornt.
Enter value ilb"red by t-e pound kq DI{CP mud
be "Dsabled otnewse you wll lrear Invald Opton,"
if you fy to sd hs vali€
Set Gateway

1. After reviewing and noting the SPA lP address using the procedure described
in the previous section, run a Web browser application.on the same network as
the SPA.
2. Open a session to the SPA by typing: http://< spa ip address >/admin/advanced
wherethe <spa ip address> is the lP address noted earlier in step 1.
3. The browser will show the tabbed user interface. Select the Line 1 tab to
configure a service for line '1.
4. Using FWD SIP VolP service as an example, in the Line 1 settings page:
lf you are using NAT do this:
. Set User lD to your FWD account's FWD number (e.9. 16000)
. Set Password to your FWD account's password
. Set Proxy to: fwd.pulver.com
. Set Use Outbound Proxy: Yes
. Set Outbound Proxy to: fwdnat.pulver.com:5082
. Press ihe Submit All Changes button at the bottom of the web page
lf you are directly connected to the Internet do this:
. Set User lD to your FWD account's FWD number (e.9. 16000)
. Set Password to your FWD account's password
. Set Proxy to: fwd.pulver.com
. Press the Submit All Changes button at the bottom of the web page
Note: More detailed configuration information for FWD and other VolP sewices may be found at: ffi.sipura.com/support
This equipment has been tested and found to comply with the limits for a
Class B digital device in accordance with the specifications in part 15 of the
FCC rules. This product bears the CE Marking indicating compliance with the
B9/336/EEC directive.
Sbndardstowhidr confonnrty is Dedared: EN 610004-2:19$, EN6100043:1S7, EN6100044:1995, EN 610@+5:1995,
EN610@46:1996, EN610@4€:1S4, EN6'10004-11:1994, EN6100G32:2001, EN6100G33:1995& EN5502:lSClassB
Modifications to this product not authorized by Sipura Technology could void
FCC approval, terminating end user authority to use this product.
For indoor use only.
Read installation instructions before connecting to a power source.
The electric plug and socket must be accessible at all times as this is the
main method to disconnect power from the device.
Shock Hazard:
" Do not operate near water or similar fluid.
Do not work with this device during periods of lightning activity.
Do not touch the phone wires at the end of cables or within sockets.
s/'PURA
technology, inc.