Skyline Exhibits Tradewinds Immerse Manual

PN 38035_C
page 1 of 9
©2018 Skyline Exhibits TradeWinds® is a registered trademark of Skyline Exhibits
Tradewinds Immerse™ Display System Setup Instructions
Packing & Unpacking............................................ 1
Standard Frames ....................................................... 1
Component Identification ................................... 2
Primary Components
Frame............................................................................. 2
Channel Bar................................................................. 2
End Cap ........................................................................ 2
LED Light ..................................................................... 2
Standard Foot............................................................. 2
Accessory Foot .......................................................... 2
Backlit Column........................................................... 2
Monitor Mount........................................................... 2
Shoe Box Shelf............................................................ 2
Heavy Duty Shoe Box Shelf ................................... 2
Assembly
Frame Assembly ........................................................ 3
Channel Bar Installation.......................................... 3
Standard Foot Installation ..................................... 4
Graphic Installation .................................................. 4
Accessories
LED Arm Light and Clip........................................... 5
Accessory Foot .......................................................... 5
Monitor Mount ...................................................... 6-7
Shoe Box Shelf ........................................................7-8
Back Lighting ............................................................. 9
Table of Contents Packing & Unpacking
Standard Frames
Frame
Bag
Channels
8’ Curved 8’ Straight
10’ Backlit 10’ Curved 10’ Straight

PN 38035_C
page 2 of 9
©2018 Skyline Exhibits TradeWinds® is a registered trademark of Skyline Exhibits
Tradewinds Immerse™ Display System Setup Instructions
Component Identification
Frame Channel Bar
Standard Foot Accessory Foot
End Cap
LED Light & Light Clip
Backlit Column Monitor Mount Shoe Box Shelf
w/ Standard Shelf Insert
Heavy Duty Shoe Box Shelf

PN 38035_C
page 3 of 9
©2018 Skyline Exhibits TradeWinds® is a registered trademark of Skyline Exhibits
Tradewinds Immerse™ Display System Setup Instructions
Push plastic tabs on end of
channel bars into corresponding
slots at the corners of the frame.
Ensure graphic channel is around
perimeter of frame.
Index posts on frame with slots in
the middle of channel bars.
Frame Assembly
1. Expand frame by pulling
outward at each corner.
Black leveling knobs indicate
bottom of frame.
2. Lock frame in open position
by connecting adjacent pins
in center of frame, black
leveling knobs should be on
bottom of the frame.
1. Identify channel bar assemblies.
2. Connect segments to create a
solid, linier span.
3. Attach channel bars to frame:
Channel Bar Installation
A
B
Note: You may lay your frame on the
ground if necessary, to install
top channels.
Frame folded
Frame unfolded
Channel bars

PN 38035_C
page 4 of 9
©2018 Skyline Exhibits TradeWinds® is a registered trademark of Skyline Exhibits
Tradewinds Immerse™ Display System Setup Instructions
1. Start at the corners of the assembly. Work the FlexLock™edge of the panel into the extrusion at each corner.
2. Press the FlexLock™ edge of the panel into the extrusion near the middle of each extrusion.
3. Work the panel into the extrusion from the corners inward and the middle outward.
4. To Dismantle, lay frame assembly on floor covered with clean drop cloth provided. To help reduce wrinkling,
carefully fold fabric panel and pack into fabric panel storage bag.
Standard Foot Installation
Graphic Installation
1. Place leveling knob into
round opening on top of foot.
2. Index opening with second
leveling knob by sliding
captured foot into position. Insert
second knob into round opening.
3. Center foot on frame so
equal distances protude out
the front and back.
Front and Sides Wrapped
Front
Graphic Installation Options

PN 38035_C
page 5 of 9
©2018 Skyline Exhibits TradeWinds® is a registered trademark of Skyline Exhibits
Tradewinds Immerse™ Display System Setup Instructions
LED Arm Light and Clip
Accessory Foot
Channel Bar
Light Mount
Light Mount
Channel Bar
Important: Note that installation of these feet must happen prior to placing any type of monitor weight to your frame.
1. Disassemble your accessory foot by twisting o the wingnut, you should now have three separate pieces
2. Slide the long base of the foot under your frame.
3. Place the top part of the foot over the endcap on the frame.
4. Twist the wingnut over the screw to ensure a tight connection between the top and bottom of the foot
5. Repeat above steps with second foot on opposite side of frame.