skyvoe NXG-46 User manual

Deck Post & Tilt Mount
Assembly Manual
NXG-32 / NXG-42 / NXG-46
*This deck post is shown with the tilt mount for NXG 4250 / NXG 4650*

3
Deck Post ManualnXG 3250 / nXG 4250 / nXG 4650 |
Table of Contents
DECK POST INSTALLATION ............................................... 5
PARTS FOR POST ASSEMBLY ........................................ 5
TILT MOUNTS .................................................................. 6
POST TO PLATE ASSEMBLY ........................................... 7
PLATE POSITION AND ANCHORING............................... 9
POST TILT MOUNT ASSEMBLY ....................................... 13
PARTS FOR POST TILT MOUNT .................................... 14
TILT MOUNTS ................................................................ 15
U-BOLTS AND MOUNTING PLATE ASSEMBLY............. 16
TILT MOUNT ASSEMBLY ............................................... 18

5
Deck Post ManualnXG 3250 / nXG 4250 / nXG 4650 |
Parts for Post Assembly:
1. 1- Post
2. 1- Base Plate
3. 1 - Post Lock - Handle
front
back
this item is found in parts box
Not Included: Anchoring hardwear for Base Plate
Gather the following:

6All Rights Reserved. 2014 SkyVue®
Assembly Manual- Deck Post
Tools Required for Post Assembly:
Tilt Mounts:
The tilt mount portion of a portable cart is provided in a separate box
labeled “PTM” and is size specic. See below for the appropriate sizes.
Ratchet with 9/16” Socket 5.5 mm Allen Wrench
9/16”
32” Class
Televisions
42” & 46” Class
Televisions

7
Deck Post ManualnXG 3250 / nXG 4250 / nXG 4650 |
Post to Plate Assembly:
Set Screw
Preinstalled
Post Lock - Handle Hole
Located on side
Bottom of Post
Brass Fitting for
Friction Reduction
Lower Cable Exit Hole
Upper Cable Entry Hole

8All Rights Reserved. 2014 SkyVue®
Assembly Manual- Deck Post
Slide bottom of post over the
sleeve that is found towards the
back of the mounting plate.
Locate the post lock handle
hole on the side of the post.
Thread the handle into
the hole.
Do not tighten completely
until post is in the preferred
viewing position.

9
Deck Post ManualnXG 3250 / nXG 4250 / nXG 4650 |
Plate Position and
Anchoring your Deck Post:
Base Plate with post
Position the base plate with post in the
spot where it is going to be mounted.
Using the four holes indicated with
the red ciricles, drill the holes for the
hardwear you purchased to secure the
base plate to the deck or patio.
After the holes are drilled insert your
hardwear and tighten securely.

10 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Deck Post
You have now completed the assembly portion of your Deck Post Mount.
You have now completed the assembly portion of your
Deck Post Mount.
Proceed to the box labeled:
PTM-32 or PTM-42-46
to complete your installation.

11
Deck Post ManualnXG 3250 / nXG 4250 / nXG 4650 |
Notes:

13
Post tilt Mount ManualnXG 3250 / nXG 4250 / nXG 4650 |
Post Tilt Mount
Assembly
*This post is shown with the tilt mount for NXG 4250 / NXG 4650*
These instructions apply to all the following Models 3250 / 4250 / 4650
NXG-3250
NXG-4250 / NXG-4650

14 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
Parts for Tilt Mount Assembly:
1. Previously assembled post:
Deck Post, In-ground Post, or
Portable Cart
2. 2- U-Bolts - (4) Flat Washers,
(4) Lock Washers,
(4) Powder Coated Nuts
3. 2- U-Bolt Saddles
4. 4 - Rubber Bolt Caps
5. Appropriately sized tilt mount
(Located in the box labeled “PTM”)
these items are found in parts box
32” Class
or
42”/46” Class

15
Post tilt Mount ManualnXG 3250 / nXG 4250 / nXG 4650 |
Tools Required for PTM Assembly:
Tilt Mounts:
The tilt mount portion of a portable cart is provided in a separate box
labeled “PTM” and is size specic. See below for the appropriate sizes.
Ratchet
with 9/16” Socket
9/16”
32” Class
Televisions
42” & 46” Class
Televisions
PTM Boxes will contain the following items:
2- Mounting Arms
1- Mounting Plate
2- Tilt Control Knobs
2- M6 Carriage Bolts
2- ABS Washers
2- Lock Washers

16 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
U-Bolts and
Mounting Plate Assembly:
U-Bolts should be hooked around the post and through the holes on the
U-Bolt Saddles. These should be positioned near the upper cable entry
hole.
With U-Bolts and saddles in place,
slide mounting plate over the U-bolt
ends.
U-Bolt
Post
Saddle
Top View

17
Post tilt Mount ManualnXG 3250 / nXG 4250 / nXG 4650 |
1. With U-bolts threaded through the mounting plates, place
stainless steel at washers over the bolt ends.
2. Place stainless steel lock washers over bolt ends.
3. Thread black powder coated nuts over bolt ends and hand tighten.
See figure 3a for suggested mounting plate placement.
4. Once positioned, level and tighten all U-bolt nuts on mounting
plate.
5. Place rubber bolt caps over exposed bolt ends
U-Bolts and
Mounting Plate Assembly Cont.:

18 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
Gather the following:
1. Slide the M6 bolt through the hole on the Control Arm
2. Place the ABS washer on the thread side of the bolt.
3. Place the lock washer on the thread side of the bolt.
4. Place then twist the knob on to the bolt.
Do not tighten all the way this will control the amount of tilt the television
has once it is put on the wall bracket.
Tilt Control Knob
x 2 x 2 x 2 x 2
M6 Bolts Lock Washer ABS Washer
Tilt Mount Assembly:

19
Post tilt Mount ManualnXG 3250 / nXG 4250 / nXG 4650 |
Lay television down, viewing side down on blanket.
Lay blanket down on at sturdy
surface. Run hand over sur-
face to make sure there are no
sharp object or protrusions,
when the television is laying
down.

20 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
Remove and set aside the 4 screws and washers as indicated with
the red circles.
Align holes of the mounting arms with the holes on the back of the
television. Reinsert the screws and washers from previous step and
tighten securely.
Align Holes Secure Screws
Note:
Both kNoBs Need
to face the sides of
the televisioN