skyvoe NXG-55 User manual

Deck Post & Tilt Mount
Assembly Manual
NXG-55
*This deck post is shown with the tilt mount for NXG 5550*

3
Deck Post ManualnXG 5550 |
Table of Contents
DECK POST INSTALLATION ............................................... 5
PARTS FOR POST ASSEMBLY ........................................ 5
TILT MOUNTS .................................................................. 6
POST TO PLATE ASSEMBLY ........................................... 7
PLATE POSITION AND ANCHORING............................... 9
POST TILT MOUNT ASSEMBLY ....................................... 13
PARTS FOR POST TILT MOUNT .................................... 15
TILT MOUNTS ................................................................ 16
U-BOLTS AND MOUNTING PLATE ASSEMBLY............. 17

5
Deck Post ManualnXG 5550 |
Parts for Post Assembly:
1. 1- Post
2. 1- Base Plate
3. 1 - Post Lock - Handle
front
back
this item is found in parts box
Not Included: Anchoring hardwear for Base Plate
Gather the following:

6All Rights Reserved. 2014 SkyVue®
Assembly Manual- Deck Post
Tools Required for Post Assembly:
Tilt Mounts:
The tilt mount portion of the deck post is provided in a separate box
labeled “PTM” and is size specic. See below for the appropriate sizes.
55” Class
Televisions
Ratchet
with 9/16” Socket
9/16”

7
Deck Post ManualnXG 5550 |
Post to Plate Assembly:
Set Screw
Preinstalled
Post Lock - Handle Hole
Located on side
Bottom of Post
Brass Fitting for
Friction Reduction
Lower Cable Exit Hole
Upper Cable Entry Hole

8All Rights Reserved. 2014 SkyVue®
Assembly Manual- Deck Post
Slide bottom of post over the
sleeve that is found towards the
back of the mounting plate.
Locate the post lock handle
hole on the side of the post.
Thread the handle into
the hole.
Do not tighten completely
until post is in the preferred
viewing position.

9
Deck Post ManualnXG 5550 |
Plate Position and
Anchoring your Deck Post:
Base Plate with post
Position the base plate with post in the
spot where it is going to be mounted.
Using the four holes indicated with
the red ciricles, drill the holes for the
hardwear you purchased to secure the
base plate to the deck or patio.
After the holes are drilled insert your
hardwear and tighten securely.

You have now completed the assembly portion of your Deck Post Mount.
You have now completed the assembly portion of your
Deck Post Mount.

Notes:

Post Tilt Mount
Assembly Manual
NXG 5550

14 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount

15
Post tilt Mount ManualnXG 5550 |
Parts for Tilt Mount Assembly:
1. Previously assembled post:
Deck Post, In-ground Post, or
Portable Cart
2. 2- U-Bolts - (4) Flat Washers,
(4) Lock Washers,
(4) Powder Coated Nuts
3. 2- U-Bolt Saddles
4. 4 - Rubber Bolt Caps
5. Appropriately sized tilt mount
(Located in the box labeled “PTM”)
these items are found in parts box

16 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
Tools Required for PTM Assembly:
Tilt Mounts:
The tilt mount portion of the deck post is provided in a separate box
labeled “PTM” and is size specic.
Ratchet
with 9/16” Socket Crescent Wrench
and
9/16”
PTM Boxes will contain the following items:
2- Mounting Arms
1- Mounting Plate
1- Locking Bar
9/16”

17
Post tilt Mount ManualnXG 5550 |
U-Bolts and
Mounting Plate Assembly:
U-Bolts should be hooked around the post and through the holes on the
U-Bolt Saddles. These should be positioned near the upper cable entry
hole.
With U-Bolts and saddles in place,
slide mounting plate over the U-bolt
ends.
U-Bolt
Post
Saddle
Top View

18 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
1. With U-bolts threaded through the mounting plates, place
stainless steel at washers over the bolt ends.
2. Place stainless steel lock washers over bolt ends.
3. Thread black powder coated nuts over bolt ends and hand tighten.
See figure 3a for suggested mounting plate placement.
4. Once positioned, level and tighten all U-bolt nuts on mounting
plate.
5. Place rubber bolt caps over exposed bolt ends
U-Bolts and
Mounting Plate Assembly Cont.:

19
Post tilt Mount ManualnXG 5550 |

20 All Rights Reserved. 2014 SkyVue®
Assembly Manual- Post Tilt Mount
Warning: Do not plug speaker bar into A/C outlet until connections to the tele-
vision have been plugged in. This will severely damage the speaker bar if not
followed completely.
Lay television down, viewing side down on blanket.
Lay blanket down on at
sturdy surface. Run hand
over surface to make sure
there are no sharp object
or protrusions, when the
television is laying down.