smania POWERBITE User manual

INSTRUCTIONS
MINI ELECTRIC CHAINSAW
POWERBITE
PACKAGE CONTENTS
•Mini chainsaw
•2 × battery pack
•Battery charger
•Wrench
•Screwdriver
TECHNICAL SPECIFICATIONS
•Power: 550 W
•Battery voltage: 24 V
•Battery capacity: 2000 mAh
•Battery type: Li-ion
•Material: ABS, metal
•Weight (without battery): 0.7 kg
•Charger adapter input: 100–240 V
•Charging time: 1.5–3 hours
•Chain speed: 5 m/s
COMPONENTS
1. Chain guide blade
2. Side cover
3. Safety bumper
4. Cover nut
5. ON/OFF switch
6. Battery pack
CHAIN INSTALLATION
1. Loosen the nut counterclockwise and remove
the side cover.
2. Install the chain guide blade: first load the chain
onto the chain guide. Ensure that chain’s inner
teeth fall into the guide slot.
3. Pay attention to the direction of the cutting
teeth.
4. When installing the guide blade, ensure the
groove on it is positioned on the main bolt.
5. Pull the chain over the sprocket and align the
pin hole.
6. Install the side cover and tighten the bolt nut.
CHAIN MAINTENANCE
CALIBRATE THE TIGHTNESS OF THE CHAIN
Calibrating the tightness of the chain on the guide
blade can offer you the best using experience. If the
chain is too tight on the guide blade, then there will
be more friction so it will wear the guide blade and
consume the battery faster. If the chain is too loose
on the guide blade, then sometimes the chain can
fall off during use.

To calibrate the tightness of the chain, simply loosen
the cover nut with a wrench and use a screwdriver
to adjust the screw behind the guide blade (no need
to take off the guide blade cover). Clockwise for
tighter chain and anti-clockwise for looser chain.
The proper tightness should be when you are able to
pull the chain off the guide blade edge baseline by
3–4 mm. Tighten the cover nut with the wrench.
REMOVE ACCUMULATED WOOD DUST
The chain and guide blade does not require oil
maintenance normally as long as you keep the two
parts clean. It is advised to do a thorough cleaning
after a few uses. Use the wrench to open the guide
blade cover and remove the accumulated wood dust
etc.
REPLACE CHAIN
When the teeth on the chain become dull, it's time
to replace it with a new chain.
See the chapter about chain installation.
CHARGING THE BATTERY PACK
1. Plug the charger into the wall socket.
2. Plug the power connector of the charger into
the charge socket on top of the battery pack.
•Once the battery is completely charged, a
green light on the mains adapter lights up.
•The device cannot be operated during
charging.
•The charger and the battery heat up during
charging. This is due to operating conditions
and not a defect.
3. Once the battery pack has finished charging,
disconnect the charger from the battery charge
socket and the plug from the wall socket.
Charge state
Indicator light state
Charger plugged into
mains
Green on, red off
Charging
Green off, red on
After charging
Green on, red off
Battery abnormal
Green and red flicks
Battery temperature
below 10 °C or over 40 °C
Green off, red flick
INSTALLING A BATTERY PACK
CAUTION:
•Always switch off the tool before installing or
removing the battery pack.
•Hold the device and the battery pack firmly
when installing or removing the battery pack.
To install the battery pack, align the tongue on the
battery pack with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click.
To remove the battery pack, slide it from the tool
while pressing the red button on the front of the
battery pack.
CHAINSAW MAINTENANCE
•There are no user-serviceable parts in your
power tool.
•Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth.
•Always store your power tool in a dry place.
•Keep the motor ventilation slots clean. Keep all
working controls free of dust.
•Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.
WARNINGS
GENERAL SAFETY
•Keep your work area tidy and well lit.
•When the chainsaw is running, keep your hands
at least 15 cm away from the blade.
•Do not operate a power tool in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.

•Keep children and bystanders away while
operating a power tool.
•Do not expose power tools to rain or wet
conditions.
•Use personal protective equipment. Always
wear eye protection.
•Do not wear loose clothing or jewelry. Keep
your hair and clothing away from moving parts.
•Keep the power tool out of the reach of children
when not in use.
•Only charge the batteries using chargers
recommended by the manufacturer.
•Do not use a damaged or modified battery.
•Do not expose batteries to fire or excessive
temperatures.
•Never service damaged battery packs.
SAFETY NOTES FOR POWER TOOL
•Keep the device and its accessories away from
hot surfaces.
•Persons with physical or mental impairments
must not use the device and its accessories
unsupervised.
•Children must not play with, clean or service the
device and its accessories.
•Let the tool cool down after use before storing
it.
•Always wait until all moving parts come to a
standstill after working with the tool.
USING AND HANDLING THE CHARGER
•Always allow sufficient ventilation when
charging the battery; gases may develop.
•Keep the charger away from any type of
moisture.
•Never use the charger in environments where
there are explosive or flammable materials.
•Do not place objects on top of the charger and
do not cover the charger.
•Keep the charger away from heat sources.
•Regularly check the charger for damage.
•The charger must not be disassembled. Repairs
must only be undertaken by an approved
technical customer service department.
•Always unplug the charger from the power
supply after use.
WARRANTY
The warranty is valid for 24 months. You can claim it
from DFVU d.o.o., Liparjeva 6a, 1234 Mengeš,
Slovenia, for a replacement product or a refund.
Send us your order number and purchase date in the
email, which is available by clicking on our logo in the
bottom right corner. The product has a lifetime of 24
months from the date of collection.
WEEE disposal and recycling symbol. The
WEEE symbol is attached to the product in
compliance with the EU directive
2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE). It is intended
to deter the improper disposal of this
product and to promote reuse and recycling.