Smarteh LPC-2.A04 User manual

USER MANUAL
Longo programmable controller
LPC-2.A04
Analog Output module
Version 1
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: [phone] / e-mail: [e-mail] / www.smarteh.si

Longo programmable controller LPC-2.A04
Written by SMAR EH d.o.o.
Copyright © 2005, SMAR EH d.o.o.
User Manual
Document Version: 001
March 31, 2006
i

Longo programmable controller LPC-2.A04
S ANDARDS AND PROVISIONS: Standards, recommendations,
regulations and provisions of the country in which the devices will
operate, must be considered while planning and setting up electrical
devices. Work on 100 .. 240 V AC network is allowed for authorized
personnel only.
DANGER WARNINGS: Devices or modules must be protected from
moisture, dirt and damage during transport, storing and operation.
WARRAN Y CONDI IONS: For all modules LONGO LPC-2 – if no
modifications are performed upon and are correctly connected by
authorized personnel – in consideration of maximum allowed
connecting power, warranty of 24 months is valid from the date of
sale to the end buyer, but not more than 36 months after delivery
from Smarteh. In case of claims within warranty time, which are based
on material malfunctions the producer offers free replacement. he
method of return of malfunctioned module, together with description,
can be arranged with our authorized representative. Warranty does
not include damage due to transport or because of unconsidered
corresponding regulations of the country, where the module is
installed.
his device must be connected properly by the provided connection
scheme in this manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous voltage in the device can cause electric shock and may
result in personal injury or death.
NEVER SERVICE HIS PRODUC YOURSELF!
his device must not be installed in the systems critical for life (e.g.
medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer,
the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected
separately!
LONGO LPC-2 complies to the following standards:
•EMC: EN 61000-6-3:2007 + A1:2011, EN 61000-6-1:2007, EN 61000-
3-2:2006 + A1:2009 + A2: 2009, EN 61000-3-3:2013
•LVD: IEC 61010-1:2010 (3rd Ed.), IEC 61010-2-201:2013 (1st Ed.)
Smarteh d.o.o. operates a policy of continuous development.
herefore we reserve the right to make changes and improvements to
any of the products described in this manual without any prior notice.
MANUFAC URER:
SMAR EH d.o.o.
Poljubinj 114
5220 olmin
Slovenia
ii

Longo programmable controller LPC-2.A04
Longo programmable controller LPC-2.A0
1 DESCRIP ION...................................................................................1
2 FEA URES.......................................................................................2
3 INS ALLA ION..................................................................................3
3.1 Connection scheme example.........................................................3
3.2 Mounting instructions.................................................................5
3.3 Module labeling........................................................................6
4 ECHNICAL SPECIFICA IONS.................................................................7
5 CHANGES .......................................................................................8
6 NO ES...........................................................................................9
iii

Longo programmable controller LPC-2.A04
1 DESCRIPTION
LPC-2.A04 is an eight analog outputs module.
Outputs can be individually set as current or voltage mode with correspondent jumper. In current
output mode module generates 0 .. 20 mA, if configured as voltage output mode it generates 0 .. 10
V on the port.
he output is supplied to target system with a resolution of 16 bits.
NO E: For proper system configuration and data allocation please refer to LPC Composer software
help menu.
1

Longo programmable controller LPC-2.A04
2 FEATURES
Figure 1: LPC-2.A04 analog module.
Table 1: Technical data
8 analog outputs
Voltage / current output range: 0 .. 10 V / 0 .. 20 mA @ ±1 % / ±1 % accuracy of full scale value
Output can be set as current or voltage type (jumper configurable)
Standard DIN EN50022-35 rail mounting
2

Longo programmable controller LPC-2.A04
3 INSTALLATION
3.1 Connection scheme example
Figure 2: Connection scheme example
3
K1 K2
LED1

Longo programmable controller LPC-2.A04
Table 1: Outputs1
set as voltage set as current
OU 1.1 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 1.2 (┴) GND
OU 2.3 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 2.4 (┴) GND
OU 3.5 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 3.6 (┴) GND
OU 4.7 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 4.8 (┴) GND
OU 5.9 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 5.10 (┴) GND
OU 6.11 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 6.12 (┴) GND
OU 7.13 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 7.14 (┴) GND
OU 8.15 (Q) analog out 0 .. 10 V
DC analog out 0 .. 20 mA
OU 8.16 (┴) GND
Table 2: K1
Internal BUS Data & DC power supply Connection to I/O module
Table 3: K2
Internal BUS Data & DC power supply Connection to I/O module
Table : LED1
Status Green LED: indicates A04 state Off: No power supply
4

Longo programmable controller LPC-2.A04
3.2 Mounting instructions
Figure 3: Housing dimensions
Dimensions in milimeters.
All connections, module attachments and assembling must be done
while module is not connected to the main power supply.
Mounting instructions:
1. Switch OFF main power supply.
2. Mount LPC-2.A04 module to the provided place inside an electrical panel (DIN EN50022-35
rail mounting).
3. Mount other LPC-2 modules (if required). Mount each module to the DIN rail first, then
attach modules together through K1 and K2 connectors.
4. Connect devices and sensor wires according to the connection scheme in Figure 2.
5. Switch ON main power supply.
6. Green LED should turn on according to the able 4.
Dismount in reverse order. For mounting/dismounting modules to/from DIN rail a free space of at
least one module must be left on the DIN rail.
NO E: LPC-2 main module should be powered separately from other electrical appliance connected
to LPC-2 system. Signal wires must be installed separately from power and high voltage wires in
accordance with general industry electrical installation standard.
5
53
90
95
36
60

Longo programmable controller LPC-2.A04
3.3 Module labeling
Figure : Labels on housing
Label 1: Label 2:
Label 1 description:
1. LPC-2.MC3 is the full product name.
2. P/N:225MC30 0001001 is the part number.
•225 – general code for LPC-2 product family,
•MC3 – short product name,
•0 001 – sequence code,
•04 – year of code opening,
•001 – derivation code,
•001 – version code (reserved for future HW and/or SW firmware upgrades).
3. D/C:16/05 is the date code.
•16 – week and
•05 – year of production.
Label 2 description:
1. S/N:MC3-S9-0500000190 is the serial number.
•MC3 – short product name,
•S9 – user code (test procedure, e.g. Smarteh person xxx),
•0500000190 – year and current stack code,
•05 – year (last two cyphers),
•00000190 – current stack number; previous module would have the stack number
00000189 and the next one 00000191.
6

Longo programmable controller LPC-2.A04
TECHNICAL SPECIFICATIONS
Table 5: Technical specifications
Power supply from internal BUS
Number of analog outputs 8
Connection type screw type connector for stranded wire 0.75 to 2.5 mm2
Max. power consumption 5 W
Max. current consumption 20 mA per output
Analog output accuracy of the full
scale value < ±1 %
Load resistance R > 500 Ω voltage mode
R < 500 Ω current mode
Analog output range 0 .. 10 V / 0 .. 20 mA
Max. transition time per channel 1 s
DAC resolution 16 bit
Dimensions (L x W x H) 90 x 53 x 60 mm
Weight 100 g
Ambient temperature 0 to 50 °C
Ambient humidity max. 95 %, no condensation
Maximum altitude 2000 m
Mounting position vertical
ransport and storage temperature -20 to 60 °C
Pollution degree 2
Protection class IP 30
7

Longo programmable controller LPC-2.A04
5 CHANGES
he following table describes all the changes to the document.
Date V. Description
31.3.2006 1 he initial version, issued as LPC-2.A04 module UserManual.
8

Longo programmable controller LPC-2.A04
6 NOTES
9