ICP DAS USA tET-PD6 User manual

Technical support: servic[email protected] P1
tET-P(D)6/tPET-P(D)6
Quick Start
v1.2, Feb. 2018
What’s in the box?
Related Information
The package includes the following items:
tET/tPET-P(D)6 Module x 1
Quick Start x1 (This Document)
tET-P6/tPET-P6/tET-PD6/tPET-PD6 Series Product Page:
Documentation & Firmware:
NS-205/NS-205PSE/DP-665 Product Page (optional):

Technical support: servic[email protected] P2
1 Connecting the Power and Host PC
1) Make sure your PC has workable network settings.
Disable or well configure your Windows firewall andAnti-Virus firewall first,
else the “Search Servers” on Chapter 5 may not work. (Please contact
with your system Administrator)
2) Connect both the tET/tPET-P(D)6 and your PC to the same sub network
or the same Ethernet switch.
3) Supply power (PoE or +12~+48 VDC)to the tET/tPET-P(D)6.

Technical support: servic[email protected] P3
2 Pin Assignments & Wiring Note
Pin Assignments:
Digital Input Wiring of the tET/tPET-P6:
To other channels
10K
DI.COM
DIx
+-
10K
DI.COM
DIx
-+
To other channels
10K
DI.COM
DIx
-+
To other channels
10K
DI.COM
DIx
+-
To other
channels
...
Readback as 1 Readback as 0
+10 ~ +50 VDC OPEN or <4 VDC
+10 ~ +50 VDC OPEN or <4 VDC
Digital Input
Sink
Source
To other
channels
...
To other
channels
...
To other
channels
...
Digital Input Wiring of the tET/tPET-PD6:
DI.GND
DIx
Relay Close
DI.GND
DIx
Relay Open
Readback as 0 Readback as 1
Relay Off Relay On
Digital Input
Dry Contact

Technical support: servic[email protected] P4
3 Wire the DI for Self-test
tET/tPET-P6:
1) Supply the External Power +24Vto DI0. (External +10V connect to Pin06 )
2) Supply the External Power GND to DI.COM. (External GND connect to
Pin05)
tET/tPET-PD6:
1) Connect the DI0 and DI.COM. (Pin06 connect to Pin05)

Technical support: servic[email protected] P5
4 Modbus Address
(1xxxx) DI address:
Begin
address
Points
Description
Bits
Per
Point
Range
Access
Type
0
(0x0)
1~6
Digital Input
1
0:Off
1:On
R
32
(0x20)
1~6
Digital latched status (high)
1
0:no
1:latched
R
64
(0x40)
1~6
Digital latched status (low)
1
0:no
1:latched
R
(0xxxx) DO address:
Begin
address
Points
Description
Bits
Per
Point
Range
Access
Type
32
(0x20)
1
Clear all DI latched status
(high)
1
1: Clear
W
33
(0x21)
1
Clear all DI latched status
(low)
1
1: Clear
W
150
(0x96)
1
Enable All DI latched
status (high/low)
1
0:Disable
1:Enable
R/W/F
151
(0x97)
1~6
Enable high speed digital
counter
1
0:Disable
1:Enable
R/W/F
.
.
.
.
.
.
.
.
.
.
.
.
Note
For detail “DI/DO Modbus Address”information, refer to Section 6.3 Modbus Register Table
of user’s manual (http://ftp.icpdas.com/pub/cd/tinymodules/napdos/tpet/document/).

Technical support: servic[email protected] P6
5 Configuring Network Settings
1) Run the eSearch Utility.
The eSearch Utility is located at:
http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/esearch/
2) Click the “Search Servers”to search your tET/tPET-P(D)6.
3) Double-click your tET/tPET-P(D)6 to configure the settings
Factory Default Settings of tET/tPET-P(D)6:
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4) Contact your Network Administrator to obtain a correct network
configuration (such as IP/Mask/Gateway). Enter the network settings
and click “OK”. Note: The tET/tPET-P(D)6 will use the new settings 2
seconds later.





Technical support: servic[email protected] P7
6 Testing your tET/tPET Module
1) Wait 2 seconds and click “Search Servers”button again to ensure the
tET/tPET-P(D)6 is working well with new configuration.
2) Click the name of tET/tPET-P(D)6 to select it.
3) Click the “Web”button to log in to the web configuration pages.
(Or enter the URL address of the tET/tPET-P(D)6 in the address bar of
the browser.)




Technical support: servic[email protected] P8
4) Enter the password in the “login password”field and click “Submit”.
5) In the “Home”page, check that the “DI0”status should show current
status is ON (Green).
Use the default
password: Admin

