Smarter Home Platform Storage Rack 4' x 8' User manual

Platform Storage Rack
4’ x 8’
INSTALLATION MANUAL
4’ x 8’

Safety Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MyLifter Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Platform Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1: Assemble Platform Overhead Storage Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 2: Install Smart Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 3: Install MyLifter Hoists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 4: Install Power Adapters and Cable Management Clips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 5: Attach Platform To MyLifters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table of Contents

1. This is a DO IT YOURSELF project. Read and follow the installation instructions carefully. Failure to follow instructions
could result in property damage, serious injury or death. If you have any questions or concerns about the quality of your
ceiling structure discontinue installation and consult a structural engineer.
2. Do not attempt to install any SmarterHome product or device without a basic understanding of these installation
instructions. If you are not confident locating and anchoring items to ceiling joists do not attempt this installation.
3. Do not exceed the stated weight limits noted on the platform overhead storage rack. Deflection of the storage rack can
happen as it reaches maximum weight load. The weight limit is based on a statically loaded storage rack that is anchored
to a wood framed garage. This system is not compatible if your house in constructed using metal studs.
4. Load the overhead storage rack evenly being sure to place heavier objects closer to the vertical uprights and the lighter
objects closer to the center.
5. Routinely inspect the storage rack to ensure rivets and wire decking are properly seated.
Safety Overview
2
WARNING

Lifting capacity (motorized) = 320 lbs | Weight Limit (non-motorized/static) = 600 lbs.

MyLifter Safety
3
When using the the MyLifter and related storage accessories:
• Do NOT use the MyLifter to lift people or animals.
• Do NOT climb or hang on the storage rack.
• Do NOT lift items while hands or other body parts are near the MyLifter device,
lifting cables, storage accessories, etc.
• Do NOT stand under the MyLifter or any items that have been lifted by the MyLifter.
• Do NOT use the MyLifter to lift or lower items over people or animals.
• Do NOT exceed the lifting capacity of the MyLifters.
• Do NOT attempt to install/secure lifters to angled ceilings or walls. MyLifter units
are designed to be secured to flat ceilings only.
• Do NOT install in any manner other than as specified in instructions.
• Do NOT attempt to lift unbalanced loads. Always balance items/loads before lifting.
Inspect the MyLifter Cable(s)
• Inspect the MyLifter cable(s) often/before each use to ensure it is properly seated on the pulley wheel. If the cable is
tangled, damaged, or bent, stop using your MyLifter device immediately.
Avoid Electric Shock
• To avoid risk of electric shock and/or other potential injury DO NOT disassemble or open any SmarterHome device. All
SmarterHome products are designed for indoor use only. Failure to follow these safety instructions could result in
property damage, serious personal injury, or death.

What’s in the Box (Drawings below are not shown to scale)
4
Center Supports
Riveted End Rails
Ceiling bracket (non-motorized install only)
Vertical Upright (3-Hole)
Wire Decking
MyLifters Power Adapters Smart Track & Hardware
Riveted Side Rails
M6 x 15mm Bolt
M6 Flange Nut
M6 Washer
Plastic Plug
Required Tools (not included)
• Drill
• Ratchet with ½” and
10mm Socket
• Stud Finder
• Ladder
• 10mm Wrench
• Rubber Mallet
• Safety Glasses
• Pencil
• Tape Measure
• Screwdriver (flat blade)

5
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform Overhead Storage Rack
1. Align the holes on two of the riveted side rails. NOTE: All four side rails are
the same so no need to worry about using the wrong ones.
2. Using the 10mm socket and wrench plus 4 bolts, 4 washers and 4 nuts,
fasten the two riveted side rails together using the outer holes only, as shown.
Place the washer on the bolt before inserting it into the hole on the side rail.
(fig 1.1). NOTE: The center holes will be used to attach the center support
later in the assembly process.
3. Repeat steps 1 and 2 for the remaining side rails. When finished with this
step, you should have two assembled side rails.
fig 1.1
Do not fasten using these holes
at this stage of assembly.

6
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform Overhead Storage Rack (cont.)
4. Join a side rail with an end rail using a vertical upright post. We suggest
using a rubber mallet and screwdriver (fig 1.2) to ensure the rivets are
properly seated.
5. Once the rivets are fully seated, insert a plastic plug as shown. (fig 1.3)
6. Repeat steps 4 and 5 for each of the four corners so all side and end rails are
fastened together.
NOTE
NOTE: Opposite ends of the side rails may come loose while hammering other side rails into place.
Be sure to check that all rivets are properly seated once you have attached all side and end rails.
Insert plastic plug to hold vertical
upright and rails in place.
fig 1.2
fig 1.3

7
fig 1.4
fig 1.4
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform
Overhead Storage Rack (cont.)
7. Fasten the center support to the
side rails as shown using the
remaining bolts, nuts and washers.
(fig 1.4)
8. Attach the remaining center
supports to the side rails by
inserting the rivets into the keyhole
openings. Make sure the rivets are
fully seated. (fig 1.5)
fig 1.5
fig 1.5

8
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform Overhead Storage Rack (cont.)
9. The frame of the platform is now fully assembled (fig 1.6) and ready to add the wire decking.
10. Place the wire decking on the platform frame. The edge of each section of the wire decking (except the outer edges)
should rest on a center support. (fig 1.7)
Edge of wire decking
resting on center supports.
fig 1.6 fig 1.7

9
Platform Installation | Smart Track Installation Overview
Step 2: Install Smart Track
• Lag bolts used to secure Smart Track must be centered in ceiling joists.
• If you are not confident locating and anchoring items to ceiling joists do not
attempt this installation.
• Smart Track is designed to be installed with two lag bolts. Load must only to
be applied between lag screws.
• Smart Track is designed to be secured to flat garage ceilings. DO NOT mount
the Smart Track to walls or angled ceilings. Failure to follow instructions
could result in property damage, serious injury, or death.
• If you have any questions or concerns about the quality of your ceiling
structure discontinue installation and consult a structural engineer.
STOP:
Read Before
Continuing

10
Platform Installation | Install Smart Track
Step 2: Install Smart Track (cont.)
1. Determine where to install your platform overhead storage rack. Be sure to
take into consideration garage doors, overhead lights etc. when choosing
your install location. Keep in mind you’ll also need access to at least one
power outlet for the MyLifters.
2. Determine where each Smart Track will need to be installed. (fig 2.1)
3. Use a stud finder to find the ceiling joist that is nearest to your desired
installation location.
4. Mark the left edge of the joist. (fig 2.2)
5. Mark the right edge of the joist. (fig 2.3)
6. Mark the center of the joist. (fig 2.4)
fig 2.2 fig 2.3 fig 2.4
fig 2.1
JOIST DIRECTION
JOIST DIRECTION
48”
48”
96”
96”

11
Platform Installation | Install Smart Track
Step 2: Install Smart Track (cont.)
7. Place the Smart Track over the center mark you made for the ceiling joist and
use a pencil to mark where the lag screws will be installed so you can drill
the pilot holes. Be sure the markings are along the center of the ceiling joist.
8. Using the included 6mm drill bit, drill the first vertical pilot hole at least three
inches into the center point of the mark you made.
9. Use a rachet with a 1/2 inch socket to attach the Smart Track to the ceiling
using one of the included lag screws and washers. Do not completely tighten
the lag bolt at this point. NOTE: If the lag screw turns freely, your pilot hole is
likely not hitting the ceiling joist. If this is the case, find the center of the stud
and drill a new pilot hole.
CAUTION

Do NOT use an impact driver to insert the lag screws into the stud. This could over tighten the screws causing
them to fail, which may result in property damage, serious personal injury, or death.

12
Platform Installation | Install Smart Track
Step 2: Install Smart Track (cont.)
11. Repeat steps 4-6 to find the center of the joist where you will secure the
other end of the Smart Track.
12. Tighten both lag screws so the Smart Track is flush and secure against the
ceiling.
13. Repeat the above steps for each remaining Smart Track that needs to be
installed.
CAUTION

Before moving to next step be sure that lag screws for all Smart Track is tightened, flush and secure against the ceiling.

13
Platform Installation | Install MyLifter Hoists
Step 3: Install MyLifter Hoists
1. Before installing the MyLifters onto Smart Track pair to each MyLifter. This is
important to ensure you can troubleshoot any potential issues before
installing them.
2. Download the MyLifter app from the App Store or Google Play (fig 3.1).
3. Open the app and tap “Add Devices” in the bottom right corner to open the
“Available Lifters” screen.
4. Firmly press the Pair button next to the Status light on the MyLifter. (fig 3.2)
5. When the Status light blinks green, the MyLifter is paired with the app. On
the “Available Lifters” screen, your newly paired MyLifter should be displayed
with its corresponding MAC address as the default name. You can edit the
MyLifter name by tapping “Edit” in the upper right corner. (fig 3.3)
6. Repeat steps 3-5 for all MyLifters that need to be paired.
7. Now Group all the MyLifters (up to 4 units) you’ll be using to lift the platform.
This ensures the MyLifters function together.
fig 3.1
fig 3.2
fig 3.3

14
Platform Installation | Install MyLifter Hoists
Step 3: Install MyLifter Hoists (cont.)
8. On the home page, click “Create Group” in the bottom left corner.
Choose “Locked Group”.
9. On the “Select Devices” screen, select the MyLifters you just paired to.
In the “Name The Group” text box. (fig 3.4)
10. Tap “Create Group” at the bottom of the screen and then “Got It” when
the please confirm dialog opens. The “Device Control” screen will open.
11. To level each MyLifter in the group, click each MyLifter one-by-one
(they’re listed at the bottom of the “Device Control” screen) and adjust
the cable length so each cable is the same length/distance from the
floor. NOTE: You may have to make additional adjustments once you’ve
attached the platform. (fig 3.5)
12. Once you’ve leveled each MyLifter, tap “Set Group Level”.
fig 3.5fig 3.4
NOTE

To make further adjust and ensure your item is level, tap the “Help”
button and select “Level Group”. Then tap on the MyLifter you’d like to
adjust and make the necessary adjustments.
DB
A
A
C
C
E
E
A. SET HIGH AND LOW POINTS
Program Smart High and Smart Low
points for safety and convenience.
B. LOAD GAUGE
Indicates the percentage of weight
MyLifter is lifting relative to its
lifting capacity.
C. SMART LIFT AND SMART LOWER
Lift and lower your items to preset
Smart High and Smart Low with
one tap.
D. VARIABLE SPEED CONTROLLER
Press and hold to activate variable
speed slider to lift/lower ensuring
perfect placement of your items.
E. MANUAL LIFT OR LOWER BUTTONS
Press and hold these buttons to
manually lift or lower your items at
full speed.
9. On the “Select Devices” screen, select the MyLifters you just paired to.
10. Tap “Create Group” at the bottom of the screen and then “Got It” when
the please confirm dialog opens. The “Device Control” screen will open.
fig 3.5
fig 3.4

15
Platform Installation | Install MyLifter Hoists
Step 3: Install MyLifter Hoists (cont.)
13. Now that you’ve paired to each MyLifter and created a group, they can be
installed on the Smart Track.
14. Each MyLifter must be placed on Smart Track between two lag screws to
ensure proper support.
15. To install MyLifter on Smart Track, align the holes in the MyLifter frame with
the holes on the Smart Track.
16. Insert the two included quick-release pins through the holes in the MyLifter
frame and the Smart Track. Make sure the pins go all the way through both
sides of the MyLifter frame and Smart Track. Repeat this for each MyLifter
that you are installing. (fig 3.6)
NOTE

NOTE: Each MyLifter must be installed between two lag screws and in the same orientation.
fig 3.6

16
Platform Installation | Install Power Adapters and Cable Management Clips
Step 4: Install Power Adapters and Cable Management Clips
1. For each MyLifter you’ve installed on the Smart Track, determine where the
Power Adapter should be installed. The preferred location, if possible, is
adjacent to the MyLifter.
2. Confirm the power cord will reach a power outlet and the DC cable will reach
your MyLifter. Remember each Power Adapter is equipped with our patented
power passthrough technology so you can power multiple MyLifters from one
power outlet.
3. Clip the universal mounting bracket, included with the Power Adapter, onto
the Smart Track. The nubs should snap into place. (fig 4.1)
4. Align the pins with the holes on the back for the Power Adapter. Press the
Power Adapter onto the pins and slide to lock it into place. (fig 4.2)
fig 4.1
fig 4.2

17
Platform Installation | Install Power Adapters and Cable Management Clips
Step 4: Install Power Adapters and
Cable Management Clips (cont.)
5. To secure and organize the cables,
determine where to place the cable
management clips.
6. Peel the adhesive backing off the
first cable management clip and
place it and created a group. Be
sure to press firmly to ensure it
sticks. (fig 4.3)
7. Secure the cable management
clip with a screw, place all wires into
the clip, and securely close the clip.
(fig 4.4)
8. Repeat steps 5-7 for additional cable
management clips to secure and
organize cables.
9. You can also organize cables by
winding the excess cable around the
power adapter housing. (fig 4.5)
10. Once you organized the cables you
can install the gray Smart Track
cable covers you removed before
installing the Smart Track. (fig 4.6)
fig 4.4fig 4.3
fig 4.6
fig 4.5

18
Platform Installation | Install Power Adapters and Cable Management Clips
Step 4: Install Power Adapters and Cable Management Clips (cont.)
10. Once all Power Adapters have been installed, connect them to the closest
outlet (this may be a wall outlet or the power pass through on another Power
Adapter).
11. The LED on the Power Adapter will glow when powered on.
12. Connect the DC cable from the Power Adapter to its corresponding MyLifter.
NOTE

Additional Garage Smart products with AC connections can be powered by connecting
their AC cable to the AC outlet on the Power Adapter.

19
Platform Installation | Attach Platform to MyLifters
Step 5: Attach Platform To MyLifters
1. On the “Device Control” screen, press and hold the Manual Lower arrow
to let out enough cable to run through the pulley block and back up to
the Smart Track. (fig 5.1)
2. Run each cable through the pulley block and attach it to the Smart
Track using the provided carabiners. (fig 5.2) NOTE: The carabiner must
be placed in the first hole next to the MyLifter on the end with the DC
power cable. (fig 5.3)
3. Using a carabiner, connect each pulley block to its corresponding 3-hole
upright on the platform. Pulleys should be parallel to the Smart Track.
When attaching the pulleys, ensure cables are not twisted. Be consistent
by attaching all pulleys to the same side of the 3-hole upright (e.g. Attach
pulleys to all “A” locations, or all “B” locations. Failure to do so can
damage the Mylifters). (fig 5.4)
fig 5.1
fig 5.2
fig 5.4
fig 5.3
DB
A
A
C
C
E
E
A. SET HIGH AND LOW POINTS
Program Smart High and Smart Low
points for safety and convenience.
B. LOAD GAUGE
Indicates the percentage of weight
MyLifter is lifting relative to its
lifting capacity.
C. SMART LIFT AND SMART LOWER
Lift and lower your items to preset
Smart High and Smart Low with
one tap.
D. VARIABLE SPEED CONTROLLER
Press and hold to activate variable
speed slider to lift/lower ensuring
perfect placement of your items.
E. MANUAL LIFT OR LOWER BUTTONS
Press and hold these buttons to
manually lift or lower your items at
full speed.
B
B
B
B
AA
A A
Attach pulleys to all “A” locations, or all “B” locations.
Failure to do so can damage the MyLifters.
TOP VIEW