Snapper IMAGE 204094 User manual

OPERATING GUIDE
Wireless TV Speaker
Item No. 204094

Thank you for purchasing the Sharper Image Wireless TV Speaker. Please read this operating guide carefully
before use and keep it for future reference. If you have any questions, please feel free to contact our Customer
Service department at 1 [phone].
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions carefully before using the Wireless TV Speaker.
• Always keep the system dry. Do not immerse
in water.
• For your safety, do not attempt to open the unit or
battery compartment. Attempting to open or opening
the battery compartment violates your warranty.
• The Wireless TV Speaker uses a lithium ion
battery. Please observe the safety and handling
instructions for the lithium ion battery. Please
dispose of the unit/used batteries properly,
following any local regulations.
• Do not dispose of the unit/used batteries in
the household trash. Do not incinerate. Take the
equipment to a nearby recycle center.
• Do not unplug by pulling on the cord. To unplug,
grasp the plug, not the cord. Unplug from outlet when
not in use and before servicing or cleaning.
Do not operate any device with a damaged cord
or plug, or after the device malfunctions, or is
dropped or damaged in any manner. Return the
device to the nearest authorized service facility
for examination, repair or electrical or mechanical
adjustment.
• This device is intended for home and personal
use only.
2 • Wireless TV Speaker

PACKAGE CONTENTS FEATURES IDENTIFICATION
1 Wireless Receiver
(Speaker)
1 Transmitter Base
1 AC Adapter
1 Audio Cord
1 Operating Guide
OPERATING GUIDE
Wireless TV Speaker
Item No. 204094
2 RCA “Y-Adapter” Cables
(optional, for maximum
connection possibilities)
Tone control
Headset port
Pairing button
(underneath)
On/o & volume control
Receiver
Low battery/
charging indicator
Power indicator
Base
(back)
AC adapter jack Audio
input port
Pairing button
(for additional
Receivers)
Wireless TV Speaker • 3

CONNECTION AND SET UP
Select an Audio Connection
Locate the audio out connector on the back
of your TV or the headphone jack.
Analog Audio Output
For analog audio output, connectors use
the included audio cords.
Headphone Jack
You may also connect the Wireless TV Headphones
via your TV’s headphone jack. Use the provided audio
cable and connect the base of the Wireless TV Speaker
to your TV as shown below.
PLEASE NOTE: In most cases, the TV speaker volume
will be muted when using this type of connection.
4 • Wireless TV Speaker

For TVs with Audio-Out Ports (RCA type)
If your TV has audio output RCA type ports on the
back of your TV, it is an analog output. Use the provided
audio cable and connect the base of the Wireless TV
Speaker to your TV as shown below.
PLEASE NOTE: In most cases, TV speakers are NOT
muted with this type of connection.
Audio Connection Expansion (for Analog Outputs)
If your TV or satellite/cable box analog output ports
have been used with other audio devices, the Wireless
TV Speaker can be connected to your TV or satellite/
cable box by using the provided RCA Y-Adapter Cables.
(There are 2 cables with color-coded connector ends to
match the L/R audio output connectors.) Connect the
Wireless TV Speaker as shown below.
Wireless TV Speaker • 5

Placement of Transmitter Base
For best results, place the Transmitter Base on top of
your TV stand, or on top of your TV, as shown below.
Battery Charging
Place the receiver on the base (as shown) for charging
for 6+ hours before first use. During charging, the
Low Battery/Charge indicator blinks. When it is fully
charged, the indicator light will stop blinking and stay
steadily lit. A fully charged battery will give you up to
8 hours of listening time.
When the receiver is not in use or when the Low
Battery indicator blinks, place the receiver on the
base for recharging.
6 • Wireless TV Speaker

OPERATION
On/O, Volume and Tone Control
1. Rotate the knob to turn receiver On or O and to
adjust its volume.
2. You can turn your TV speaker to Low or to O.
On some TVs, you may need to use your remote
to go into the TV’s Menu to achieve an optimal
audio/speaker setting. Please refer to your TV user
manual for details.
3. To conserve battery power, the receiver will shift into
standby mode if no audio signal is received from the
base (after your TV is turned o) for a period longer
than three minutes. The volume ON/OFF indicator
will be o during this standby time. When audio
signal is received, the receiver will re-activate.
NOTE: If the receiver has hibernated too long and
missed the contacts with the base, rotate the knob,
turn o the receiver and then turn the receiver back
on again to re-sync with the base.
4. Set the Tone Control to a position that enables you to
hear and understand the dialog best.
Pairing Additional Receivers
You can add up to 50 receivers to work with your base.
Each added receiver, must be “paired” with the base
as follows:
• Make sure your new receiver is fully charged.
• Make sure your current base and receiver is working
properly and audio is playing on the receiver.
• Continue the audio playing to the base and receiver.
Volume
Tone Adjustment
Wireless TV Speaker • 7

Pairing Additional Receivers (continued)
1. Turn the new receiver ON.
2. Press and hold (about 5 seconds) the PAIRING
button on the bottom of the receiver until the ON/
OFF indicator starts blinking. Pairing period is
approximately 20 seconds.
3. Press and hold (about 3 seconds) the PAIRING button
on the back of the base until the power indicator
starts blinking. It will start pairing with the new
receiver.
4. As soon as pairing is successful (less than 2
seconds), the new receiver’s ON/OFF indicator will
stop blinking, and audio sounds will be played within
5 seconds.
5. Repeat these steps again if pairing is not successful.
Using Headphones
Plug your headphones into the headphone jack as
shown. No sound will be emitted from the speakers.
Adjust the headphone volume by rotating the
volume knob.
Back of
transmitter
(Base)
Bottom
of receiver
(Speaker)
8 • Wireless TV Speaker

TROUBLESHOOTING
• No sound from the receiver
Check all connections to ensure that all the cords
are firmly connected at the back of the base and TV.
Also, confirm that the receiver is not more than 100
feet away from the base.
• There is sound from the TV speaker, but no sound
from the receiver
Check your TV speaker setting by going into the
TV Menu, using your TV remote and ensuring the
TV is sending audio signals to the base.
• The Low Battery/Charging indicator keeps blinking
on the receiver
This indicates that the battery is low and needs to
be placed on the base for recharging. When fully
charged, the blinking will stop (in about 3 hours).
If the blinking does not stop, check to make sure
the receiver is firmly connected and properly aligned
to the base.
CLEANING AND MAINTENANCE
Unplug the AC Adapter from the wall. Then, use a dry,
soft cloth to clean and dust the outside surfaces and
the charging contacts on the Base. Do not immerse
the Receiver in water.
SPECIFICATIONS
Transmission: 2.4 GHz Radio Frequency
Speakers: 2x5W Class D
Speaker Battery: Built-in Lithium Ion Battery
Operating Range: Over 30m (100 feet)
in an open field
AC Adapter Power: 100-240VAC/50-60 Hz input;
9VDC 1.5A output
Listening Time: About 8 hours (at 50% volume)
Dimensions: 24cm x 17cm x 8cm
(9”x7”x3.25”)
Weight: 800g. (1.7 lbs.)
(Final product may vary)
Wireless TV Speaker • 9

WARRANTY INFORMATION
Your Wireless TV Speaker comes with a one year
limited warranty. We warrant during this warranty
period from the date of purchase to the original
consumer that the Wireless TV Speaker will be free
from defects in materials and workmanship under
intended home use. In the event that your Wireless
TV Speaker fails to function properly within one year
of original purchase due to defects in materials or
workmanship, please contact our Customer Service
department at 1 [phone] for instructions.
This warranty does not apply to any product that has
been accidentally damaged due to: abuse, misuse,
negligence, use on electrical frequency or voltage
other than marked on product and/or described in this
manual. Defects or errors caused by unauthorized
alterations, repairs and/or tampering are also not
covered by this warranty.
Incidental or Consequential Damages
Sharper Image is not responsible for any incidental or
consequential damages, including, without limitation,
commercial loss of profit or for any incidental
expenses, loss of time or inconvenience. Some states
do not allow exclusion or limitation of incidental or
consequential damage, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights. You may
have other legal rights that vary from state to state.
10 • Wireless TV Speaker